Home - Blaupunkt
Installation Guide for MLAUPUNKT models including: 1 311 24 015 45 01, 1 311 24 016 45 01, TPMS 2.2 Tire Pressure Monitoring System, TPMS 2.2, Tire Pressure Monitoring System, Pressure Monitoring System, Monitoring System, System
0~8 Bar / 0~116 PSI.
File Info : application/pdf, 16 Pages, 2.37MB
DocumentDocumentTIRE PRESSURE MONITORING SYSTEM TPMS 2.2 Operating and Installation Instructions CAUTIONS Safety Notes This TPMS (Tire Pressure Monitoring System) has been manufactured according to established safety guidelines. Nevertheless, risks may arise if the safety instructions outlined in this manual are not adhered to. The purpose of this manual is to acquaint the user with the crucial functions of the TPMS. Prior to operating the appliance, carefully read through this manual and store it in a readily accessible location. Furthermore, ensure compliance with the instructions for any devices used in conjunction with this appliance. Road Safety Always adhere to the following guidelines for road safety: · Utilize the device in a manner that enhances the user's safety while operating the vehicle. It is advisable for the user to park at a suitable location when inspecting the tires in the event of an abnormal alert General Safety · The device is designed for installation and operation in a vehicle with a 12V system, and therefore, it should be installed at least 500mm away from the DVD or other high-power equipment to prevent signal disruption during a system outage. · It is crucial not to dismantle or modify the device. Installation or repair should be carried out by a specialist. Blaupunkt assumes no responsibility for any loss or damage resulting from unauthorized disassembly or modification of the device. · The device's primary function is to monitor tire pressure and temperature exclusively. The driver is responsible for maintaining the tires. Blaupunkt is not responsible for any loss of sensors. If sensors are lost, contact your Blaupunkt dealer to purchase new ones. · The package includes pre-set sensors for designated tires. If sensor replacement or a change in sensor location is necessary, ensure that the sensors are reprogrammed before operating the device. · Please refrain from operating the device under extreme temperature conditions (either extremely high or low). Ensure that the car's interior temperature falls within the range of -10°C to 60°C before beginning the installation process and during operation. Disclaimer · Blaupunkt is not liable for any loss or damage caused or resulting from unauthorized disassembly or modification to the product. · Under no circumstances shall Blaupunkt be held liable for any direct, indirect, punitive, incidental, or special consequential damages, whether related to property or life, arising out of or connected with the use or misuse of our products, including but not limited to issues of improper storage. · USA & CANADA: This product is not intended for sale in the United States and Canada. If acquired in the U.S. or Canada, it is obtained on an "as-is" basis. No warranty, whether express or implied, is provided in the U.S. and Canada. This manual may be updated from time to time without any notice. Visit www.blaupunkt.com for more info. 1 STRUCTURE & FUNCTIONS Display 34 2 1 7 8 10 9 11 External Sensor 56 1 2 3 4 5 6 Valve Sensor 1 2 3 4 Receiver 1. Pressure Alarn Icon 2. Tire Temperature Value 3. Pressure Unit 4. Temperature Unit 5. Set Button 6. Return Buttom 7. Sensor Batery Alarm icon 8. Tire Pressure Value 9. USB Power Supply Interface 10. Sticker 11. Fix Support External Sensor 1. Sensor Cover 2. Battery Holder 3. Battery 4. Sensor 5. Rubber Seal 6. Base 2 Valve Sensor 1. Dust Cap 2. Aluminium Alloy Nut 3. Aluminium Alloy Valve 4. Transmitter SPECIFICATIONS Sensor Operating frequency Battery voltage Operating temperature Pressure range Display Operating current Operating frequency Operating voltage Operating temperature Dimension (LxWxH) Default Value High pressure value Low pressure value High temperature value Precision Temperature Pressure Temperature unit Air pressure unit Accessories 433.92 +/- 0.03MHz DC2.1V ~ DC 3.3V -20°C ~ 85°C (External Sensor) -40°C ~ 125°C (Valve Sensor) 0~8 Bar / 0~116 PSI <40mA 433.92 +/- 0.05MHz 12V/5V -30°C ~ 85°C 45 x 38.8 x 16.5mm 3.1Bar/45Psi 1.8Bar/27Psi 85°C ±3 °C 0.15 Bar / 2.2 PSI 1 °C = 33.8 °F = 274.15 K 2 Bar = 14.5 PSI = 100 Kpa = 1.02Kgf/cm Display 1x Bracket TPMS 2.2E 3M Tape (20x20mm) Hardwire Kit (Optional) 4x External Sensor 4x Anti-theft Nut TPMS 2.2V 4x Rubber Seal 1x spanner (keep in car) 4x Built-in Battery 4x Valve Sensor 4x Warning Label 3 EXTERNAL SENSOR INSTALLATION 1. Remove the valve cap. 4. Tighten up the nut to the sensor by using the spanner. 2. Screw in the nut. 5. Spray soap water on the nozzle to check for leakage problem. 3. Screw on the sensor. 6. Clean the area before using it. 4 EXTERNAL SENSOR BATTERY REPLACEMENT 1. Unscrew the nut. 4. Replace new battery. 2. Unscrew the sensor. 5. Refer to "Sensor Installation" steps. 3. Unscrew the sensor cover by using spanner. 5 VALVE SENSOR INSTALLATION 1. Remove the original air valve from the wheel barrel. 4. Rebalance the wheel to ensure radial uniformity. 2. Install & adjust the valve sensor onto the wheel barrel. Screw & tighten the nut & valve. 5. Reinstall the balanced wheel onto the vehicle. 3. Inflate the tire after installation. 6 DISPLAY INSTALLATION 1. Remove the protective film from the 3M tape and place it on the bracket. Sticking area 3. Place the bracket and affix it to the center of the back of the display. Sticking area 2. Remove the protective film from the other side of the 3M tape as well. 4. Attach the display with the bracket to the blades of car's air conditioning vent, then adjust it to the desired position and angle. TROUBLESHOOTING If any of the following problems occur, please refer to the Troubleshooting section for potential solutions. If the problem persists, seek assistance from an authorized Blaupunkt dealer. Problems Air leakage after sensor installation No tire data are displayed after completing installation Missing or lost sensor External sensor battery low Change of tire location Solutions The tire valves may not be universal standard, please check with the local dealer Ensure ACC is turned on If external sensor, check rubber seal condition New installation requires user to drive above 2 km/h for about 5min Please purchase new sensor Please replace with battery CR1632 Please reprogram the corresponding sensors Refer to Tire Position Exchange Setting (P2) 7 DIFFERENT SCENARIO 3. Low Pressure · Emits beeping alarm sound 1. Normal · Displays real time tire pressure & temperature of 4 tires. 4. High Pressure · Emits beeping alarm sound 2. Sensor Failure · Emits beeping alarm sound 5. Air Leakage · Emits beeping alarm sound 8 DIFFERENT SCENARIO 6. High Temperature · Emits beeping alarm sound OPERATION INSTRUCTION 1. First Start-up Interface a) Booting-up Process interface 7. Sensor Low Voltage · Emits beeping alarm sound b) Standby Interface · First use · After first used 9 OPERATION INSTRUCTION 2. Sensor Pairing a) Press & hold button "SET" to enter Menu interface. b) After hearing beeping sound, P1 will appear. c) Press & hold button "SET" to enter the Sensor Pairing mode stored in display. e) When the new Sensor ID left front wheel is detected, it is stored automatically. Then, it will continue to next order. Press button " " to exit setting interface. (Pairing order : Front Left > Front Right > Rear Right > Rear Left) f ) · External sensor - Disassemble the external sensor from the front left tire & reinstalled, for sensor ID pairing activation. · Valve sensor - Releasing the air from tire continously instead of intermittently, ensure that the releasing process is not less than 8 second. - Do not exceed the maximum pressure of tire during inflating. d) Short press "SET" to switch the preferred position & entering the Sensor ID (the tire symbol will move and the original sensor ID will display). · Ensure that there is only one of the tire with sensor is activated during pairing, otherwise there is no guarantee that the sensor ID that really needs to be paired will be paired into the receiver. · To cancel the current pairing process by pressing return key, however pairing process cannot be canceled 10 OPERATION INSTRUCTION 3. Tire Position Exchange Setting (It is required only when the tires has switched location) a) Press & hold button "SET" to enter Menu interface. e) Press and hold button "SET" to confirm front wheel ID adjustment and tire replacement. Once the tire replacement is successful, the system will beeps twice. Press button " " to exit setting interface. b) After hearing beeping sound, P2 will appear. 4. Thresold Value Setting a) Press & hold button "SET" to enter Menu interface. c) Press & hold button "SET" to enter the Sensor change interface. d) The left and right front wheel interfaces wait for exchange confirmation. Air pressure display flashes until confirmed. b) After hearing beeping sound, P3 will appear. 11 OPERATION INSTRUCTION c) Press & hold button "SET" , then Short press button "SET" again to switch between thresold value interface (High Pressure Value, Low Pressure Value & High Temperature Value) · High Pressure Value Setting Interface d) Select the preferred interface by press and hold button "SET ". The digit wil flash then press the button " SET" again to set the value & long press "SET" to confirm. e) Press button " " to exit setting interface. · Low Pressure Value Setting Interface · High Temperature Value Setting Interface 12 WIRING DIAGRAM Method 1 : USB Charger 5V USB Output Car USB Port or Cigarette Charger 5V USB Output Method 2 : Hardwire Kit (Optional) IN 12V OUT 12V + Fuse DC12-USB5V - ACC Ground 13 Blaupunkt Car Entertainment - Asia Pacific Competence Centre R0 TPMS 2.2 E 1 311 24 015 45 01 TPMS 2.2 V 1 311 24 016 45 01