User Manual for Optoma models including: DC455 Document Camera, DC455, Document Camera, Camera
OPTOMA DC455 (01) PDF MANUAL - Manual-Hub.com
DC455 Document Camera English User manual https://manual-hub.com/ · Welcome: Thanks for purchasing this product. Please read the instructions carefully before using this product. · FCC Compliance Statement (Class A): This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. · Federal Communications Commission (FCC) Statement : This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. · European Community Compliance Statement (Class A): This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. The symbol of the crossed out wheeled bin indicates this product should not be placed in municipal waste. Instead, you need to dispose of the waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. https://manual-hub.com/ Warning 1. Do not look directly at the LED light source,which may cause retinal damage. 2. Carry the product by holding the lower part of the main unit in both hands. Never hold the product by the arm or the camera head only. 3. The camera can be damaged if it hits a desk surface or any hard object. 4. Never turn the arm in the opposite direction. 1 https://manual-hub.com/ Preparing the Document Camera »»Knowing the Document Camera Parts Camera Head LED Lamp Lens Rotary Control Panel SD Card Slot Remote Control Signal Receiver Speaker Remote Control Signal Receiver 2 https://manual-hub.com/ Anti-theft Slot HDMI Input Port HDMI Output Port VGA Input Port VGA Output Port USB Port DC 5V Power Socket Microphone »»Control Panel HDMI OUTPUT VGA PC LAMP BRIGHT FLIP PLAY ZOOM - FREEZE RECORD MENU ZOOM+ AF SNAP Button Function Power on/off Invert image 180° "Freeze" the current image or "Pause" the clip while playing video Capture a still image Show or hide Menu Direction button Zoom out Zoom in One-time auto focus Button Function Pass the signal from PC Show/hide brightness adjustment bar. Turn on/off the LED lamp and adjust the brightness. Record a video clip Enter playback mode to display recorded still images and video clips OUTPUT HDMI/VGA output switch 3 https://manual-hub.com/ »»Remote Control Button Function Brightness hotkey Power on / off Freeze current image. * Pause the clip while playing videos Show or hide on-screen icons To show or hide OSD menu Playback mode to display recorded pictures and video clips Invert image 180° Select and adjust Record a video clip Capture a still image / Zoom out / Zoom in Button Function One-shot auto focus / Use the level bar to adjust the focus manually Not available (Only supported in optical zoom lens models) Highlight function on / off Adjust highlighted / masked area size Set color for highlighted / masked area Increase / decrease the sound volume. Mask function on / off Not available (Only applicable to optocal zoom models) Picture in Picture function on / off *For displaying a still image as an insert while displaying another image. Infrared remote control can only be used in proximity to the unit. Remove the battery cover and load the batteries into the battery compartment correctly according to the "+" and "-" symbols. Be sure to use two AAA batteries. Do not use new and old batteries or different battery types together. 4 https://manual-hub.com/ »»Setting up · Camera Head Roll the lens rotator to rotate image 90°. 90° 90° · Illumination Lamp If you are in a dark environment, please turn the LED lamp on to make better exposure. 1. Press the LED lamp button ( ) on the base to turn on/off the LED lamp. 2. Adjusting the brightness by pressing the lamp button ( ) 5 https://manual-hub.com/ »»Basic Operation · Menu options in Preview Mode Name Brightness Icon Option - Graphic Effect White Balance Text B&W Negative Sketch Auto Fluorescent Tungsten Custom Description Use the Right / Left buttons to make the image brighter / darker To improve the tint of color-based subjects such as pictures or figures. The function is designed especially for text-based documents to which can be enhanced white and black subjects such as characters and lines. To output a black & white camera image.To make the image easier to view,select this when shooting black & white documents etc. To output a negative image. To output a sketch image There are various modes (Auto, Flurescent, Tungsten and Custom) for user to choose and fit in different surroundings. Quick Zoom 2X / 4X Set the quick zoom to 2X or 4X. Image Size 0.8M / 2M / 5M / 13M Select the desired still image resolution. Video Mode High Quality High Frame Rate Select the desired video quality. 6 https://manual-hub.com/ Beep Flicker USB Connection HDMI Out VGA Out Language Clock Format Reset default On / Off Setting 50Hz / 60Hz Disk PC cam Off Enable beep sound on / off Set flicker frequency to 50Hz or 60Hz. The flicker setting is based on the frequency standard of your local power supply. Select "Disk" to enter Mass storage Mode Select "PC Cam" to enter PC Cam Mode Disable USB function 720p / 1080i Select output resolution XGA / UXGA / 720P / WXGA - Select output resolution Allows you select the language used for OSD - Set date and time No / Yes No / Yes Format the storage medium. Note that all files stored in the medium will be gone. Restore factory defaults. Note that your current settings will disappear. · Menu options in Playback Mode Function Icon Option File Info - Slide show On / Off Volume - Delete one Yes / No Delete all Yes / No Camera - Description View the file's title , saved date and time , size and the length of recording. Start a slide show with selected interval time. Use the Right / Left buttons to adjust volume Delete current file. Delete all images of the same type stored in the memory. Exit playback mode and back to preview mode. 7 https://manual-hub.com/ Adjusting the brightness 1. Press BRIGHTNESS button on the control panel ( ) or remote control ( ). 2. Use ( or ) buttons to increase or decrease the brighness level. · Zoom Function 1. Use the Zoom button ( / ) to zoom in or zoom out the screen. · Adjusting the focus · Automatic focus Press AF button ( ) to do an one-time auto focus. This function provides a one-shot auto focus. · Manual focus Use the manual focus buttons ( / ) on remote control to finetune the focus. · Anti-glare Anti-glare sheet is a transparent plastic that is overlaid on top of shiny object or glossy surface to reduce the glare. To use, simply place the anti-glare sheet on top of shiny object to glossy surface such as magazine to reduce light reflection. 8 https://manual-hub.com/ · Inserting and Ejecting a SD / SDHC card (Not supplied) 1.Insert a memory card (SD/SDHC/MMC/MMC 2.0) with the label facing up until it reaches the end of the slot. 2.When the card is inserted successfully, the icon ( ) will appear on screen and the internal memory will become inaccessible. 3.To remove the card, push the card to release it and then pull it out gently. When using a new memory card, you are recommended to format the card with the device. Do not turn off the device while formatting the SD card. Even if your card has been formatted on other devices, you may have to reformat the card with the device. If no external storage devices are connected, all files will be saved in the built-in memory. · Recording a video clip / Taking a still picture 1. Set the capture or record resolution. 2. Press the Recording button ( ) to start recording and press it again to stop recording Output Switch Resolution Setting Recording resolution VGA HDMI XGA UXGA 720P WXGA 720P 1080i 1024 x 768 1280 x 720 1280 x 800 1280 x 720 1920 x 1080 3. Press the Snap button ( ) to take a still picture. · Playback 1. Press PLAYBACK button ( ) 2. The last recorded picture or video clip will play. 3. Use Up /Down button to choose files. 9 https://manual-hub.com/ Making the Connections System Diagram DC IN VGA OUT VGA IN HD OUT HD IN Step 1 / Plugging in the Power Outlet Use power adapter to connect DC IN connector on the product to a standard 100V~240V AC power outlet. The type of power adapter is depending on your countries / regions. Step 2 / Output Resolution and Aspect Ratio. Various output resolutions are available depending on the output and aspect ratio setting. Please refer to the table listed below : Out put VGA HDMI Aspect-Ratio 4:3 16:9 16:9 Resolution 1024 x 768 1600 x 1200 1280 x 720 1280 x 800 1280 x 720 1920 x 1080 Vertical Frequency 50 / 60 Hz 50 / 60 Hz 50 / 60 Hz *Document camera will downgrade the output resolution automatically when the connected display device doesn't support highest resolution. 10 https://manual-hub.com/ Step 3 / Connecting with Components Product Port Cable Display Device Port PC Port VGA RGB OUTPUT RGB INPUT HDMI HDMI OUT HDMI IN USB Micro USB RGB INPUT RGB OUTPUT HDMI-INPUT HDMIOUTPUT TYPE A Port · Connecting the Output Display Turn on projector or any display device Connect a VGA Cable to VGA OUT Port (or HDMI Cable to HDMI OUT Port) Connect the other end of VGA Cable to VGA In Port (or other end of HDMI Cable to HDMI In Port) of your projector or display device. DC IN VGA OUTV TVGA IN HD OUT HD IN RGB HDMI HDMI 11 https://manual-hub.com/ · Connect via USB Press MENU ( ) button select "USB Connect". Choose "Disk" to connect mass storage. Choose "PC Cam" to use as a PC-Cam. · Copying files to your computer Please notice that the video clips are recorded in AVI format and are compiled as CLIPxxxx.avi (xxxx are four serial numbers). Before viewing these videos on your PC, you may need to install some media programs. 1.Turn on the document camera. 2.Connect the product to your computer with USB cable. 3.Press MENU ( ) select "USB Connect" choose "Disk". The built-in memory or external memory will be detected. Then, You can view the image data on a SD card on the PC's viewer software or simply cut/copy and paste the file to your PC. · Using product as a PC cam 1. Connect the product to your computer. Turn on your computer, then connect the accessory USB cable to the USB port of your computer. Make sure the connector and the port are aligned correctly. Switch to PC Cam mode. Connect the other end of the USB cable to the main unit. Power on press MENU ( ) Setting select USB Connect select PC Cam ( ) and press OK button to confirm. 2. Launch PC Camera After the product is correctly connected to and detected by your PC, you are ready to use PC Camera function. 12 https://manual-hub.com/ · Passthrough Function To display computer image, press PASSTHROUGH button ( ) on the control panel. For laptop to output display mode, use the keyboard command ( Fn + ) to swtich between the display modes. For different command, please refer to your laptop manual. The signal is only pass through from VGA IN port to VGA OUT port or HDMI In port to HDMI Out port on document camera. Please connect an output device to display the image on computer. DC IN HD OUT HD IN RGB For laptop to output display mode, use the keyboard command ( Fn + ) to switch between the display modes. For different command, please refer to your laptop manual. 13 https://manual-hub.com/ »»Advanced operation · Highlight function 1. Use the Highlight display to draw attention to a particular section of the output image. 2. Press the Highlight button ( ) on the remote control, and use the direction buttons to move the nighinght area. · Mask function 1. You can mask a section of the output image. 2. Press the Mask button ( ) on the remote control, and use the direction buttons to move the masked area. Press the Size button ( ) on the remote control, and use the direction buttons to adjust the highlighted / masked size. Press the Color button ( ) on the remote control, and use the direction buttons to adjust the color of highlighted / masked area. · PIP (Picture in Picture) function 1. Press the PIP button ( ) to display an around quarter-size still image on a live display. 2. Use the up / down button to move the still image to the top left and bottom left. 3. Use the left or right button to change the shift between still images. 14 https://manual-hub.com/ · Connect to a microscope Connect to a microscope enables you to examine microscopic objects on a big screen. 1. Adjust the microscope and focus objects. 2. Choose an appropriate microscope adapter. 3. Microscope adapter accessories are applicable to Ø28mm,Ø31mm, Ø33mm, and Ø34mm eyepieces. For eyepieces of about Ø33mm and Ø34mm, only a microscope adaptor with Ø33 or Ø34mm label should be installed. For a Ø28mm eyepiece, insert the Ø28mm adapter into the microscope adapter. For a Ø31mm eyepiece, insert the Ø31mm adapter into the microscope adapter. Ø33 Ø34 mm Ø28 mm Ø33 Ø34 mm Ø31 mm Ø33 Ø34 mm 4. Mount the microscope adapter onto the Lens. 5. Switch the focus mode to Macro. Press MENU ( ( ) -->select Macro or press Macro button ( )--> select Focus )( ) on remote controller. 6. Connect the lens with microscope adapter to the microscope. If the image is not clear. Please adjust the focus of microcope. Press the AF button ( fine-tune the focus. ) or use the manual focus button on remote control to 15 https://manual-hub.com/ »»Storing 1. Power off the product. OUTPUT 2. Unplug the AC adapter from the wall outlet. Disconnect the AC Adapter and all cables. 3. Fold the camera head and arms in the way shown in the figure. 16 https://manual-hub.com/ »»Troubleshooting Problem Cannot power on normally. Cause The AC adapter is not correctly connected to the wall outlet or the document camera. Solution Re-connect one end of the AC adapter to the document camera and the other end to a wall outlet. Cannot take pictures Out of memory. and video clips. Free some space from the SD / MMC card or the internal memory. Using a "protected" SD card. Set the SD card to be written in. No image output after The document camera is not Re-connect all related cables with the connecting. correctly connected to the external device correctly. external device. Incorrect input type of display Set up correct input type of display output device. output device. Incorrect output switch setting Switch output switch to correct mode. for display device. PC pass through button indicator is on. Press [ ] pass through button to turn off the function. The image is fuzzy. Probably the distance of Press AF button to auto focus or adjust object is too close to the lens. by Manual Focus. The image is reverse. The document is not put in Press [ ] button to adjust the the recommend working area. direction. The image dose not Camera image is set to move. Freeze [ ]. Press the [ ] button on the control panel again toun-pause. Remote control cannot work. No power. Replace the AAA batteries in the remote control. Object is blocking the remote Remove obstruction in front of the control signal receiver of the product. product. The distance of usage is too Stand closer to the product to use the far. remote control. 17 https://manual-hub.com/ Problem Cause Solution The LCD screen The format of the memory displays "MEMORY card is not compatible with ERROR" or "CARD the document camera. ERROR" message or The memory card is memory card cannot corrupted. be read. Format the card. Replace the memory card with a new one. Cannot delete the The lost recordings are saved The lost recordings are saved in the pictures and video in the internal memory. internal memory. clips, and also cannot find them in the memory card. Cannot view the video clips on my computer. Software is not installed on Software is not installed on the the computer. computer. TV screen does notdisplay after connecting the product to TV. The product is not correctly Reconnect the product to TV correctly. connected to the TV. Noises occur when The flicker setting does not viewing images on match the standard of the the LCD screen or on country you are staying. the computer. Adjust the flicker setting .For more information, please refer to the "Flicker Settings" table. 18 https://manual-hub.com/ ADDITIONAL INFORMATION USA 47697 Westinghouse Drive, Fremont, CA 94539, USA www.optomausa.com Japan 888-289-6786 510-897-8601 services@optoma.com 3-25-18 :0120-380-495 info@os-worldwide.cmo www.os-worldwide.com Canada 47697 Westinghouse Drive, Fremont, CA 94539, USA www.optomausa.com Latin America 47697 Westinghouse Drive, Fremont, CA 94539, USA www.optomausa.com Europe Unit 1, Network 41, Bourne End Mills, Hemel Hempstead, Herts, HP1 2UJ, United Kingdom www.optoma.eu Service Tel : +44 (0)1923 691865 Benelux BV Randstad 22-123 1316 BW Almere The Netherlands www.optoma.nl 888-289-6786 Taiwan 510-897-8601 12F., No.213, Sec. 3, Beixin Rd., services@optoma.com Xindian Dist., New Taipei City 231, Taiwan, R.O.C. www.optoma.com.tw a 888-289-6786 510-897-8601 Hong Kong services@optoma.com Unit A, 27/F Dragon Centre, 79 Wing Hong Street, Cheung Sha Wan, Kowloon, Hong Kong w +44 (0) 1923 691 800 +44 (0) 1923 691 888 service@tsc-europe.cmo China 5F, No. 1205, Kaixuan Rd., Changning District Shanghai, 200052, China w +31 (0) 36 820 0252 +31 (0) 36 548 9052 +886-2-8911-8600 +886-2-8911-6550 services@optoma.com.tw sia.optoma.com +852-2396-8968 +852-2370-1222 ww.optoma.com.hk +86-21-62947376 +86-21-62947375 ww.optoma.com.cn France Bâtiment E 81-83 avenue Edouard Vaillant 92100 Boulogne Billancourt, France +33 1 41 46 12 20 +33 1 41 46 94 35 savoptoma@optoma.fr Spain C/ José Hierro,36 Of. 1C 28522 Rivas VaciaMadrid, Spain +34 91 499 06 06 +34 91 670 08 32 Deutschland Wiesenstrasse 21 W D40549 Düsseldorf, Germany +49 (0) 211 506 6670 +49 (0) 211 506 66799 info@optoma.de Scandinavia Lerpeveien 25 3040 Drammen Norway PO.BOX 9515 3038 Drammen Norway +47 32 98 89 90 +47 32 98 89 99 info@optoma.no Korea WOOMI TECH.CO.,LTD. 4F, Minu Bldg.33-14, Kangnam-Ku, Seoul,135-815, KOREA korea.optoma.com +82+2+34430004 +82+2+34430005 19 https://manual-hub.com/ www.op2to0ma.com https://manual-hub.com/ TS-82-925-90021