Instruction Manual for USX MOUNT models including: XML030-K Full Motion TV Wall Mount, XML030-K, Full Motion TV Wall Mount, Motion TV Wall Mount, TV Wall Mount, Mount
USX MOUNT Full Motion TV Wall Mount for 42"-82" TVs, Swivel and Tilt TV Mount, Wall Mount TV Bracket with Articulating 6 Arms, Max VESA 600x400mm, 120 lbs, 16" Wood Studs with Wall Drilling Template : Electronics
This product is designed for use in wood stud, solid concrete walls - DO NOT install into drywall alone. ○ The wall must be capable of supporting five times ...
R XML030-K INSTRUCTION MANUAL For 42-82" TV If you have any questions along the way, just message to us. We're ready to help! USA-C0 ! CAUTION: PLEASE READ ENTIRE MANUAL PRIOR TO USE AND SAVE THESE INSTRUCTIONS Before getting started, let's check below lists to make sure it is just right for you! 1 Check your TV VESA is within Min and Max size MAX:600mm/23.62" (MIN:200mm/7.87") MAX:400mm/15.74" (MIN:100mm/3.94") No? This mount is NOT compatible. Yes? Perfect ! 2 Does your TV (including accessories) weigh MORE than 120 lbs. (54.5 kg)? Max: 120 LBS (54.5 kg) No? Perfect you may continue. Yes? This mount is NOT compatible. 3 What is your wall made of? Drywall with wood studs? Per fect ! ! CAUTION: DO NOT install into drywall alone Per fect ! ! CAUTION: DO NOT exceed the maximum weight indicated. This mounting system is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in collapse of the mount and its accessories, causing possible injury. Solid concrete ? Unsure? Mail to us via Amazon. Wood Stud Install Concrete Install Do you have all the tools 4 needed? (NOT INCLUDE) CAUTION 5 Tape Measure Pencil Screw driver Electric Drill 1/2 in. (13 mm) Socket Wrench Stud Finder 7/32 in. (5.5 mm) Wood Drill Bit 3/8 in. (10 mm) Masonry Drill Bit Hammer This product is designed for use in wood stud, solid concrete walls - DO NOT install into drywall alone The wall must be capable of supporting five times the weight of the TV and mount itself Do not use this product for any purpose not explicitly specified by manufacturer Manufacturer is not responsible for damage or injury caused by incorrect assembly or use 2 Dimensions TV INTERFACE 200mm [7.87in] 3-D 400mm [15.74in] 100mm [3.94in] WALL PLATE 600mm [23.62in] 144mm [5.67in] 406mm [16.00in] 9mm [0.35in] TOP VIEW - EXTENDED SIDE VIEW - EXTENDED 388mm [15.26in] +5° -15° FULLY ASSEMBLED MOUNT 685mm [26.97in] TOP VIEW - RETRACTED SIDE VIEW - EXTENDED 178mm [7.01in] 420mm [16.54in] 73mm [2.86in] 435mm [17.13in] +45° 3 Parts and Hardware ! WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! NOTE: Not all hardware included will be used. Parts and Hardware for STEP 1 TV Brackets TV Screws M4x12mm M4x30mm a x4 d x4 M6x12mm M6x35mm Spacers M8x22mm 10mm g x4 2.5mm h x4 M6x17mm b x4 M8x25mm e x4 M8x45mm i x8 j x4 M4 Washers M6 06 x2 4 c x4 f x4 k x4 l x4 Parts and Hardware for STEP 2 Wall Plate Unit Velcro x3 05 x1 Mounting template R 8 "(20 3.2mm) 1 6"(4 06 .4mm) Level Lag Bolt 01 x4 Concrete wall anchor (NOT INCLUDED) Concrete Wall Anchor Ø10x50mm 4pcs Contact us and message to us to have these additional pieces shipped directly to you. Parts and Hardware for STEP 3 M6x8mm Bolt 02 x4 Extension Arm 07 x2 M6x16mm Bolt 03 x2 Extension Arm 08 x2 Allen Key 04 x1 5 STEP 1 Attach Brackets to TV 1-1 Select TV Screws M4 M6 M8 6 1-2 Figure out the suitable position of brackets LOW MOUNTING HOLES 06 HIGH MOUNTING HOLES INSTALL UP/DOWN IF NEEDED ! TV BRACKETS MUST BE LEVEL ! 7 1-3 Need Spacer? No, choose suitable screws and washers. abc kl 1-4 Attach the TV Plate No! Yes, choose suitable screws, washers and spacers. de f kl gh i j Tips: If you need to combine M6/M8(c/e/f) screws with 2.5mm spacers( i ), you have to remove the inner circle. 8 STEP 2A Attach Wall Plate to Wall Wood Stud Option ! CAUTION: Avoid potential personal injury or property damage! Drywall covering the wall, must not exceed 5/8 in. (16 mm) Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm) Maximum horizontal space between fasteners: 16 in. (406 mm) Stud center must be verified 1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using a thin nail, or an edge to edge stud finder. 2. Position the mounting template at your desired height and line up the holes with your stud center line. Level the wall plate and mark the hole locations. 1 Again, find another wood stud 2 16" Centre line Mounting template 9 3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit. ! IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). Be sure to drill into the center of the studs. 4. Install wall plate 05 using four lag bolts 01 . Tighten the lag bolts only until they are pulled firmly against the wall plate. ! CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts. Go to STEP 3 on PAGE 13. 3 2.5"(64mm) 4 7/32" (5.5mm) 10 UP No! 01 05 STEP 2B Attach Wall Plate to Solid Concrete Wall ! CAUTION: Avoid potential personal injury or property damage! Mount the wall plate assembly 05 directly onto the concrete surface Minimum solid concrete thickness: 8 in. (203 mm) 1. Position the mounting template on the wall at your desired height. Level the wall plate and mark the hole locations. 2. Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit. ! IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). 1 2 Mounting template 3/8" (10mm) 2.5"(64mm) 11 3. Insert four anchors. ! CAUTION: Be sure the anchors are seated flush with the concrete surface. 4. Insert wall plate 05 using four lag bolts 01 . Tighten the lag bolts only until they are pulled firmly against the wall plate. ! CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts. 3 4 UP Concrete Wall Anchor (Not included) 01 05 No! Please contact us and message to us to have these additional pieces shipped directly to you. 12 STEP 3 Extension Arms and end support Assembly Please make sure you install these extension arms in right direction. Outside 07 Inside Inside 08 Outside 02 04 13 STEP 4 Wall Plate Installation Integrity Test Before hanging TV, please try to pull the mount to make sure that it has been assembled on the wall tightly. 120 LBS (54.5 kg) 14 STEP 5 Hang and Secure TV to Wall Plate Hang TV/bracket assembly onto wall plate, wrap clips on bracket around extension arms and tighten them using bolts 03 . 1 TV 2 03 04 15 STEP 6 Adjustments 6-1 TV leveling adjustment (±4°): Loosen 4 leveling bolts on the rear of TV plate by maximum 2 turns, adjust to level, and retighten to secure. ±4° Loosen Tighten 04 16 6-2 Tilting angle adjustment (+5°/-15°) Pull TV to your desired angle then fasten 2 tilting bolts with Allen key 04 . +5° Tighten Loosen -15° +5° Tighten -15° Loosen 17 6-3 Cables manage: Manage TV cables orderly and guide them through the velcros. Velcro 18福昕阅读器PDF打印机 版本 10.0.122.3451