Joy-IT Helpdesk
For Makers and Professionals | Joy-IT
Instruction Manual for Joy-IT models including: SEN-MMA5482Q, 3 Axsis Digital Acceleration Sensor Module, SEN-MMA5482Q 3 Axsis Digital Acceleration Sensor Module, Digital Acceleration Sensor Module, Acceleration Sensor Module, Sensor Module, Module
7 lug 2022 — MMA8452Q address, 0x1D(28). # Select Control register, 0x2A(42). #. 0x00(00) StandBy mode bus.write byte data(0x1D, 0x2A, 0x00). # MMA8452Q address, 0x1D(28).
Beschleunigungssensor MMA8452Q | Joy-IT
3-akse accelerometer sensor modul til Arduino (MMA8452)
File Info : application/pdf, 6 Pages, 752.00KB
DocumentDocument3-AXSIS DIGITAL ACCELERATION SENSOR MODULE SEN-MMA5482Q 1. GENERAL INFORMATION Dear customer, Thank you very much for choosing our product. In the following, we will show you what you need to consider during commissioning and use. Should you unexpectedly encounter problems during use, please do not hesitate to contact us. www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn 3. COMMISSIONING WITH THE RASPBERRY PI Wiring: Raspberry Pi MMA8452Q GND (Pin 6) GND 3v3 (Pin 1) VCC SDA (Pin 3) SDA SCL (Pin 5) SCL Installation: To be able to use the ADC, you have to enable I2C. Enter the following command: sudo raspi-config Now navigate to the point Interfacing Options -> I2C and enable the I2C interface. www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn Now create a file with the extension ".py" and copy the code example into it. Then execute this file with the console command shown below: sudo python file-name.py You should now see the values of the three axes as a console output. Code example: # Distributed with a free-will license. # Use it any way you want, profit or free, provided it fits in the licenses of its # associated works. import smbus import time # Get I2C bus bus = smbus.SMBus(1) # MMA8452Q address, 0x1D(28) # Select Control register, 0x2A(42) # 0x00(00) StandBy mode bus.write_byte_data(0x1D, 0x2A, 0x00) # MMA8452Q address, 0x1D(28) # Select Control register, 0x2A(42) # 0x01(01) Active mode bus.write_byte_data(0x1D, 0x2A, 0x01) # MMA8452Q address, 0x1D(28) # Select Configuration register, 0x0E(14) # 0x00(00) Set range to +/- 2g bus.write_byte_data(0x1D, 0x0E, 0x00) time.sleep(0.5) # MMA8452Q address, 0x1D(28) # Read data back from 0x00(0), 7 bytes # Status register, X-Axis MSB, X-Axis LSB, Y-Axis MSB, Y-Axis LSB, Z-Axis MSB, Z-Axis LSB data = bus.read_i2c_block_data(0x1D, 0x00, 7) # Convert the data xAccl = (data[1] * 256 + data[2]) / 16 if xAccl > 2047 : xAccl -= 4096 yAccl = (data[3] * 256 + data[4]) / 16 if yAccl > 2047 : yAccl -= 4096 zAccl = (data[5] * 256 + data[6]) / 16 if zAccl > 2047 : zAccl -= 4096 # Output data to screen print "Acceleration in X-Axis : %d" %xAccl print "Acceleration in Y-Axis : %d" %yAccl print "Acceleration in Z-Axis : %d" %zAccl www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn 3. COMMISSIONING WITH THE ARDUINO Wiring: ARD-Uno 3.3V GND A4 (SDA) A5 (SCL) MMA8452Q VCC GND SDA SCL To use the sensor with the Arduino, you must first install a library. Go to Tools -> Manage libraries... www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn Now enter mma8452q in the search box above and install the library SparkFun MMA8452Q Accelerometer. You can now select one of the example files under File -> Examples -> SparkFun MMA8452Q Accelerometer and upload it to your Arduino. Go to Tools and make sure you selected the correct board and port . www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn 4. ADDITIONAL INFORMATION Our information and take-back obligations according to the PR Electrical and Electronic Equipment Act (ElektroG) Symbol on electrical and electronic equipment: This crossed-out dustbin means that electrical and electronic appliances do not belong in the household waste. You must return the old appliances to a collection point. Before handing over waste batteries and accumulators that are not enclosed by waste equipment must be separated from it. Return options: As an end user, you can return your old device (which essentially fulfils the same function as the new device purchased from us) free of charge for disposal when you purchase a new device. Small appliances with no external dimensions greater than 25 cm can be disposed of in normal household quantities independently of the purchase of a new appliance. Possibility of return at our company location during opening hours: SIMAC Electronics GmbH, Pascalstr. 8, D-47506 Neukirchen-Vluyn, Germany Possibility of return in your area: We will send you a parcel stamp with which you can return the device to us free of charge. Please contact us by e-mail at Service@joy-it.net or by telephone. 5. SUPPORT If there are still any issues pending or problems arising after your purchase, we will support you by e-mail, telephone and with our ticket support system. E-Mail: service@joy-it.net Ticket system: http://support.joy-it.net Telephone: +49 (0)2845 9360--50 (9:30-17:30 o`clock) Veröffentlicht: 07.07.2022 SIMAwC wwElwwec.wjtor.oyjo-niytic.-nsiteG.tnmebt H PPaascsacalsltsrt.r8.,8474570560N6eNuekiurckhirecnh-eVnlu-yVnluyn