Automate Push 15 Programming Guide

Safety Information

WARNING: Read all safety instructions before installation and use. Improper installation or use may cause serious injury and void the warranty. Follow all instructions for user safety. Keep this guide for future reference.

• Avoid exposure to water, moisture, humid environments, or extreme temperatures.
• This product is not intended for use by persons with reduced physical, sensory, or mental capabilities, or those lacking experience, unless supervised.
• Modifications outside the scope of this manual will void the warranty.
• Installation and programming should be performed by a qualified installer.
• Use only with motorized shading devices.
• Inspect regularly for proper operation; do not use if repair or adjustment is needed.
• Keep clear of the operating area.
• Use only the specified battery type.

Battery Hazard Warning: Do not ingest batteries. This product contains a coin/button cell battery which, if swallowed, can cause severe internal burns within 2 hours, potentially leading to death. Keep new and used batteries away from children. Discontinue use and keep away from children if the battery compartment is not secure. Seek immediate medical attention if batteries are suspected to have been swallowed or ingested.

Dispose of batteries responsibly; do not mix with general waste.

Technical Specifications:

FCC ID: 2AGGZMT020101008
IC: 21769-MT020101008
Operating Temperature: -10°C to +50°C
Ratings: 3VDC, 15mA

FCC & ISED Compliance: This device complies with FCC Part 15 and ISED Canada's licence-exempt RSS standards. Operation is subject to the conditions that it does not cause harmful interference.

Installation and Setup

Wall Mounting

Attach the remote's base plate to the wall using the provided fasteners and anchors.

Battery Management

For battery-powered motors, avoid complete discharge for extended periods; recharge promptly when the battery is low.

Charging Instructions

Charge motors for 6-8 hours as per specific motor instructions. A low battery is indicated by 10 beeps from the motor.

Charging a Li-ion Zero Wire-Free Motor

Step 1: Rotate the cover cap to access the motor head.

Step 2: Connect the charger to a power source (use an extension cord if necessary).

Step 3: Plug the micro USB end into the motor. A flashing green light indicates charging; a solid green light signifies a full charge. Charging time may vary up to eight hours. Mobile phone chargers can also be used.

Step 4: Disconnect the charger and replace the cover cap.

Battery Replacement

Use a coin or tool to twist the battery cover to unlock it. Replace the CR2450 battery with the negative side facing up. Secure the cover by twisting it back to the locked position.

Installer Functions

Remote Button Overview

The Push 15 remote features a display screen and control buttons:

• Display: Shows status, channel, and group information.
• P2 Button: Used for programming and setting favorite positions.
• Lock Button: Locks or unlocks remote settings.
• (+) / (-) Buttons: Navigate channels/groups or adjust settings.
• Stop Button: Halts shade movement; also used in programming sequences.
• Up Arrow: Opens the shade.
• Down Arrow: Closes the shade.

Check Motor Direction

Step 1: Press the motor's P1 button for 2 seconds until it responds (e.g., Jog and Beep). This is part of the initial setup.

Step 2: Use the remote's Up/Down arrows to verify motor direction. If incorrect, proceed to "Change Direction"; otherwise, skip to "Set Top Limit".

Change Motor Direction

To reverse motor direction during initial setup, press and hold the Up and Down arrow buttons simultaneously for 5 seconds until the motor Jogs.

Set Top Limit

Move the shade to the desired upper limit using the Up arrow. Press and hold the Up arrow and Stop buttons together for 5 seconds to save the position. The motor will confirm with a Jog and Beep.

Set Bottom Limit

Move the shade to the desired lower limit using the Down arrow. Press and hold the Down arrow and Stop buttons together for 5 seconds to save the position. The motor will confirm with a Jog and Beep.

Factory Reset

To reset all motor settings, press and hold the P1 button for 14 seconds. The motor will perform 4 Jogs followed by 4 Beeps.

Remote State (Lock/Unlock)

Pressing the Lock button shows the remote's current state. Holding the Lock button for 6 seconds toggles between locked ('L' displayed) and unlocked ('U' displayed) modes.

User Guide Functions

Group Programming

Create custom groups (A-E) by adding individual channels (1-15).

Steps:

1. Select a group (A-E) to program.
2. Hold (-) and STOP for 4 seconds; the display shows "G" (Group Programming Mode).
3. Use (+) to select channels (1-15) to add.
4. Use (-) to toggle channel inclusion in the group. A Group Channel Indicator confirms addition.
5. Press STOP to save changes. The remote returns to Normal Mode.

Group Channel View

View channels included within a selected group.

Steps:

1. Select a group channel (A-E) to view.
2. Hold (+) and STOP for 2 seconds; the display shows a Linked Symbol and individual channels.
3. Use (+) and (-) to scroll through included channels.
4. Press STOP to confirm. The remote returns to Normal Mode.

Channel or Group Selection

Use (+) or (-) to cycle through channels or groups. Use Up/Down arrows to control the shade's position.

Leveling Control

Double-tap the Stop button to enter level control mode. Use Up/Down arrows to set the shade to a specific percentage.

Hide Groups/Channels

Select a group or channel using (+) or (-). Hold STOP to confirm hiding. This action hides the selected item and all subsequent items.

Set a Favorite Position

Move the shade to the desired position using Up/Down arrows. Press STOP (motor responds: Jog x1, Beep x1), press STOP again (motor responds: Jog x2, Beep x2), then press P2 on the controller (motor responds: Jog x3, Beep x3).

Disable Limit Setting (Lock Remote)

Ensure all programming is complete before locking. To lock, hold the Lock button for 6 seconds ('L' displayed). To unlock, hold the Lock button again for 6 seconds ('U' displayed).

Add or Delete Controller/Channel

Use the P2 button on the respective controller (A or B) to add or delete controllers/channels. Motor response indicates the action.