Pattern+Bee Eye Moving Head Light

Installation and operating instructions

After the power is plugged in and the switch is turned on, "rSt" is displayed. The moving headlights are being reset, please do not operate.

• Plugged into a grounded power outlet for indoor use only.
• Do not expose the device to rain or moisture, avoid the risk of fire or electric shock. Make sure that no flammable objects are near the device.
• Install the equipment in a well-ventilated place at least 50cm from any surface, and ensure that the ventilation slots are not blocked.
• Disconnect the equipment from the power supply before any operation.
• The ambient temperature should not exceed 40°C, and the maximum ambient temperature is 45°C. Do not operate the device at higher temperatures.
• The equipment should be stopped immediately if a fault occurs, and do not repair the equipment yourself. Improper maintenance can result in damage and malfunction. Contact technical support for repair approval. Only the same accessories can be used with the original parts, and make sure the power cord is not blocked or damaged.
• Do not expose your eyes to light sources, which can be a sign of a seizure in sensitive people.
• The lamps are only used for decoration and not suitable for ordinary household lighting.
• Replacing the fuse: Unplug the device from the power supply, remove the fuse holder from its original position with a screwdriver, take out the burnt fuse, replace the fuse with the same characteristics, then re-rotate the screw, and connect the device to the power supply superior.
• WARNING: Stop using it if the fuse is still blowing after being replaced. Please contact customer support for further instructions, continued use may cause serious damage.
• Fix the equipment with the screw holes on the bracket to ensure that the equipment is firmly fixed to prevent vibration and movement during operation, and always check whether the structure of the equipment is strong enough to withstand equipment that is at least ten times.
• The equipment must be fixed by professionals in places that elders and children cannot reach, and no one can pass under or over the pedestrian crossing. ⚠️ CAUTION: DO NOT OPEN THE HOUSING. SHOCK HAZARD ⚡. Please read this manual carefully before operating this product.
• End-of-life of the product: This sign indicates that this product should not be thrown into household waste in European Community countries and that waste should be recycled to support the sustainable recycling of resources in order to protect the environment and human health. Utilize. If you need to recycle used electrical appliances, please go to an electrical appliance collection center or contact the dealer where you purchased the product to ensure the ecological recycling of the product.

Startup steps for various modes

1. Automatic mode

Press "MENU" to find "SLnd", press "ENTER".

Press "Up" or "Down" to select "SoUd" and press "ENTER" key.

2. Sound Mode

Press "MENU" to find "Soud" and press "ENTER".

Press "Up" or "Down" to select "SoUd" and press "ENTER" key.

Technical Parameters

Voltage: AC100-240V 50/60 HZ

Light source 1: 6 Cree 4IN1 (RGBW) lamp beads

Light source 2: 1 pcs white light

Channel: 16CH/18CH

Control mode: DMX512, Sound, Auto, Master-slave

X axis: 540°

Y axis: 180°

Unpacking instructions

When you receive the device, open it and check whether the goods are complete. If not, please notify the carrier immediately and preserve the packaging, and if the damage is revealed, preserve the packaging and all packing materials for safe transportation of the device.

• 1 pcs lamps
• 1 instruction manual
• 1 power cord
• 1 bow bracket
• 2 screws (installed on the machine)

LED DISPLAY

Diagram of the LED display and control buttons:

• 1. Control buttons (MENU UP DOWN ENTER)
• 2. Display
• 3. Microphone
• 4. DMX IN
• 5. DMX OUT
• 6. POWER IN
• 7. Fan

Diagram showing dimensions: 28.5cm height, 10cm width.

Procedure for Installing support

1. Install the bow bracket and fix it with screws.
2. Install the bow bracket with the bow bracket.
3. Confirm that the bracket position is installed correctly.
4. Position is installed successfully. Confirm whether the bracket.

Hook brackets are not included in the package.

Console mode and master-slave mode

DMX OUT to the DMX IN of the No. 1 fixture; DMX OUT of the No. 1 fixture is connected to the DMX IN of the No. 2 fixture.

Press "MENU" to find "Addr", press "ENTER", display "A001" press "Up" or "Down" to select the value of the console; Master and slave settings: No. 1 light fixture is set to self-propelled or voice-activated function according to the startup mode; 2, 3, and 4**** are set to DMX512 mode: DMX address code is 001;

Diagram showing a DMX controller connected to four moving head lights in a series.

Menu description

System reset