User Manual for Merlin models including: E8003 3 Channel Universal Receiver, E8003, 3 Channel Universal Receiver, Universal Receiver, Receiver
Merlin E8003 Receiver - Secure Entry
INSTALLATION The receiver and antenna use TV Type F coaxial connectors. The antenna can be connected directly to the receiver or it can be installed remotely using a coaxial cable extension kit (Model
File Info : application/pdf, 2 Pages, 1.04MB
DocumentDocument3-CHANNEL UNIVERSAL RECEIVER MODEL E8003 with Security+ 2.0 APPLICATION The receiver can be used as a single or three channel receiver to control up to 3 gates, commercial operators or residential door openers. The receiver can also be used with a 3-button remote control to operate the OPEN, CLOSE and STOP feature on a commercial door operator. Each channel is compatible with a specified number of remote controls and keypads. Refer to the list below: · CH1: 50 remote controls and 2 seperate keypads · CH2: 20 remote controls and 2 seperate keypads · CH3: 20 remote controls and 2 seperate keypads Normally Open dry contact outputs. CH3 has both Normally Open & Normally Closed dry contact outputs. When the channel has reached full capacity for remote controls, all LEDs will blink 3 times. When the channel has reached full capacity for keypads, all LEDs will blink 4 times. Additional accessories can be programmed, however, the newly programmed accessory will replace the first programmed accessory. NOTE: The receiver will only allow you to program a button on the remote control to one channel at a time. For example, if the button on the remote control or keypad is already programmed to channel 1 and then is programmed to channel 3, the button will be erased from channel 1 and will only work on channel 3. Momentary Closure: The outputs are automatically programmed for a momentary closure of 0.4 seconds when using hand held remote controls E970M, etc. Constant Closure Output: The outputs are automatically programmed to remain closed when receiving a constant signal (press & hold) only when using Keypads and Wireless Wall Controls, E840M, E148M, E138M etc To prevent possible SERIOUS INJURY or DEATH from electrocution: · Be sure power is NOT connected BEFORE installing the receiver. To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: · ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. · Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. · ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. To prevent possible SERIOUS INJURY or DEATH, the use of CONSTANT OPERATION on residential openers is PROHIBITED. When a receiver is used to activate a commercial door opener, a reversing edge MUST be installed on the bottom of the door. Failure to install a reversing edge under these circumstances may result in SERIOUS INJURY or DEATH to persons trapped beneath the door. WIRING Refer to your commercial door operator or gate operator owner manual or wiring diagrams for specific wiring information. SINGLE CHANNEL Receiver Single Operator(s) LEDs + with Security+ 2.0 INSTALLATION CH3 CH1 CH2 The receiver and antenna use TV Type F coaxial connectors. The antenna can be connected directly to the receiver or it can be installed remotely using a coaxial cable extension kit (Model G86LMT, 7.6m). 1 Select a location for the receiver which allows access to the terminals and space for the antenna. Ensure antenna does not touch metal surfaces. DO NOT bend or fold the antenna. 2 Fasten the receiver securely with the hook and loop fasteners (provided) or screws (not provided). 3 After installation is complete, connect power. You may use a wired-in transformer, or power provided from your operator (9-30 V AC,12-40 Vdc). THREE CHANNEL Receiver Operator 3 Operator 2 Operator 1 WIRING CONTINUED OPEN, CLOSE, STOP Receiver Single Operator 3-Button Control Device Refer to your door operator or gate operator wiring diagrams for instructions on connecting two or more 3-Button control devices. PROGRAMMING PROGRAM A SINGLE BUTTON REMOTE CONTROL 1 Press and release the Learn button for the selected channel on the receiver. The corresponding LED will glow steadily for 30 seconds. 2 Within 30 seconds press and hold the button on the remote control that you wish to program to the receiver. 3 Release the remote control button when the LED on the receiver blinks, then turns off. Programming is complete. Repeat the steps above for each remote control you would like to program. PROGRAM A 3-BUTTON REMOTE CONTROL AS OPEN, CLOSE, AND STOP 1 Press and release the CH1 Learn button on the receiver. 2 Within 30 seconds press the desired OPEN button on the remote control. 3 Press and release the CH2 Learn button on the receiver. 4 Within 30 seconds press the desired CLOSE button on the remote control. 5 Press and release the CH3 Learn button on the receiver. 6 Within 30 seconds press the desired STOP button on the remote control. NOTE: If a remote control button is not pressed within 30 seconds, the LED next to the selected Learn button will turn OFF. In that case, repeat the programming. TO ERASE THE MEMORY 1 Press and hold the Learn button for the channel you want to erase. Release the button when the corresponding LED turns off; the memory has been erased. FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER: 1800 638 234 CH1 Learn Button CH2 Learn Button CH3 Learn Button SPECIFICATIONS Contact Rating. . . . . . . . . . . . . . . . 5 Amps 28 Vac or dc Max. Power . . . . . . . . . . . . . . . . . . . .9-30V AC or 9-34V DC, 50mA RF Frequency:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433MHz NOTE: If your operator does not meet the power specifications you will need a low voltage power supply. For indoor installation only. COMPATIBLE ACCESSORIES Remote Controls . . . E970M, E980M, E945M, E940M, E943M, Keypads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E840M Wireless Wall Controls . . . . . . . . . . . . E148M, E138M, E128M Antenna Extension Kits . . . . . . . . . . . . . . . . . . . . . . . . G86LMT, Antenna Only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K77-36541 CHAMBERLAIN AUSTRALIA PTY LTD PO BOX 1446 LANE COVE NSW 1595 PHONE TOLL FREE: 1800 638 234 CHAMBERLAIN NEW ZEALAND LTD PO BOX 100-221 NORTH SHORE 0745 PHONE TOLL FREE: 0800 653 667 gomerlin.com.au gomerlin.co.nz 114-5882-000