Instruction Manual for SERVER models including: 07794 Server Express Pump, 07794, Server Express Pump, Express Pump, Pump
SERVER EXPRESS 07794 (01) PDF MANUAL - Manual-Hub.com
Server ExpressTM Pumps MODEL 07794 Used with pouches up to 1½ gallons with 16mm fitments. Thank You ...for purchasing our Server ExpressTM Pump. ExpressTM pouched condiment systems are sealed and sanitary, achieve excellent evacuation and have only a few parts for easy clean-up. SIMPLIFY CONDIMENT MANAGEMENT--GO POUCHED https://manual-hub.com/ ASSEMBLY WASH ALL PARTS PROPERLY BEFORE USE. See page 3. 1 INSERT PINCH VALVE into pump housing. TIP: Squeeze the pinch valve open before installation to ensure it isn't stuck shut. 2 INSTALL DOME Press dome into housing fully. Ensure valve flap covers bottom opening. Wrap loop around lower opening to secure dome. 3 INSTALL TUBE Lubricate with a small amount of clean water. Rotate and position until both pegs on housing fit into holes on tube. 4 INSERT CONNECTOR Lubricate with a small amount of clean water. Rotate and position until both pegs on connector fit into holes on tube. Connector must point away from end of discharge tube. 5 SELECT DISCHARGE FITTING CONSISTENCY OF WHAT YOU DISPENSE THIN (hot sauce) THICK (ketchup or mustard) PARTICULATES (relish or tartar sauce) SUGGESTED FITTING SIZE SMALL MEDIUM LARGE Fittings are marked small, medium or large on bottom. 6 INSERT DISCHARGE FITTING into pump housing discharge tube. Place loop of fitting around peg on end of discharge tube to secure. Page 2 https://manual-hub.com/ SAFETY According to food and safety regulations, most foods must be stored and/or served at certain temperatures or they could become hazardous. Check with local food and safety regulators for specific guidelines. Server Products, Inc. cannot be responsible for the serving of potentially hazardous product. IMPORTANT Clean, rinse, sanitize, and dry parts daily or regularly to comply with local sanitization requirements. NSF International (National Sanitation Foundation) lists this pump as: "Not acceptable for dispensing potentially hazardous foods." DISASSEMBLY CLEANING 1 FLUSH & RINSE all pump surfaces with hot water. Place lower end of pump into container of hot water and operate pump until all remaining product is expelled and only hot water is discharged. 2 DISASSEMBLE & CLEAN all washable parts with soap and hot water. Use brush to clean any confined areas. 3 RINSE fully with clear water. 4 SANITIZE all parts according to local sanitization requirements. All parts in contact with food must be sanitized. 5 AIR DRY all parts fully. YES! Use dishwashing soap, hot water and nylon brush · Dishwasher safe · Do not use abrasive, caustic or ammonia based cleansers. · Do not use cleansing agents with high concentrations of acid, alkaline or chlorine. · Do not use metal scrapers or cleaning pads that could scratch surfaces. Page 3 https://manual-hub.com/ MODEL 07794 PART QTY DESCRIPTION 07383 1 07798 1 07388 1 07089 1 07381 1 07795 1 07796 1 07797 1 PUMP DOME, BLACK LARGE PINCH VALVE PUMP HOUSING 7" TUBE CONNECTOR, 16MM DISCHARGE FITTING, .156, SM. DISCHARGE FITTING, .256, MED. DISCHARGE FITTING, .394, LG. DOME 07383 PINCH VALVE 07798 PUMP HOUSING 07388 TUBE 07089 CONNECTOR 07381 DISCHARGE FITTING 07795, 07796, or 07797 TROUBLESHOOTING TIP: Squeeze the pinch valve open before installation to ensure it isn't stuck shut. SERVER PRODUCTS LIMITED WARRANTY Server Products equipment is backed by a two-year limited warranty against defects in materials and workmanship. For complete warranty information go to: www.Server-Products.com DIFFICULT TO ATTACH PARTS? · Wet parts with clean water to help fit. PRODUCT DOESN'T PUMP? · Ensure pinch valve is inserted in housing. · Ensure connector is snapped fully in place to fitment in pouch. · Ensure pump is properly installed in unit. · Clean pump thoroughly. DOME POPS OFF? · Clean thoroughly. Food residue could prevent a tight seal between dome and housing. · Ensure dome edges are flush with housing. GENERAL SERVICE, REPAIR OR RETURNS Before sending any item to Server Products for service, repair, or return, contact Server Products customer service to request a Return Authorization Number. Merchandise must be sent to Server Products with this number. Service is extremely prompt. Typically, units are repaired and ship out within 48 hours of receipt. Merchandise being returned for credit must be in new and unused condition and not more than 90 days old and will be subject to a 20% restocking charge. HELP or ORDERING REPLACEMENT PARTS Server Products Inc. 3601 Pleasant Hill Road Richfield, WI 53076 USA 262.628.5600 | 800.558.8722 SPSALES@SERVER-PRODUCTS.COM Please be prepared with the Part Numbers for your items. Individual part numbers are listed above. Page 4 https://manual-hub.com/ Manual #01671-RevE 042815