PERLESMITH FULL-MOTION TV WALL MOUNT

1. Compatible VESA Patterns

Ensure your TV's VESA mounting pattern is compatible. The mount supports the following patterns:

If your TV is not compatible, please contact product support.

2. Check Max Load

Max Load Capacity: 150 lbs (68kg)

⚠️ WARNING: Do not exceed the Max Load. Exceeding the Max Load can cause the mount to fail, leading to personal injury and/or property damage.

If your TV weighs more than 150 lbs, this mount is NOT compatible.

3. Verify Wall Type

This mount is designed for installation on:

• Wood Studs (with Drywall): Max stud width 24" (610mm). ✔️ Perfect
• Solid Concrete: ✔️ Perfect

⚠️ WARNING: DO NOT install on drywall alone.

❓ Unsure? Contact us.

4. Tools Needed (Not Included)

For Wood Stud Walls:

• ? Electric Drill
• ✏️ Pencil
• ? Phillips Screwdriver
• ? Tape Measure
• ? Stud Finder
• ? Awl
• ?️ 7/32" (5.5mm) Wood Drill Bit
• ? 1/2" (13mm) Socket Wrench

For Solid Concrete:

• ? Electric Drill
• ✏️ Pencil
• ? Tape Measure
• ? Hammer
• ?️ 3/8" (10mm) Concrete Drill Bit
• ? 1/2" (13mm) Socket Wrench

5. Important Safety Information

⚠️ CAUTION: Avoid the risk of personal injury or property damage!

• This product is designed for installation on wood studs and solid concrete. DO NOT install on drywall alone.
• The wall must be capable of supporting four times the weight of the TV and mount combined.
• This product contains small parts that may pose a choking hazard.
• Do not use this product for any purpose that is NOT explicitly specified in this manual.
• Do not exceed the maximum weight capacity. PERLESMITH is not liable for damage or injury caused by incorrect assembly, improper mounting, or inappropriate use.
• Before starting assembly, verify that all parts are included and undamaged. Do not use damaged or defective parts. If you require replacement parts, please call technical support or email customer service.

⚠️ WARNING: All fasteners must be firmly tightened!

Step 1: Hardware for Attaching Brackets to TV

Not all hardware included in this package will be used.

For M6 TVs:

• TV Bracket (01) x 2
• M6/M8 Washer (B1) x 4
• L2.5mm Spacer (E1) x 8
• L10mm Spacer (E2) x 4
• L22mm Spacer (E3) x 4
• M6 x 15mm TV Bolt (C1) x 4
• M6 x 35mm TV Bolt (C2) x 4

For M8 TVs:

• M8 x 15mm TV Bolt (D1) x 4
• M8 x 35mm TV Bolt (D2) x 4
• M8 x 50mm TV Bolt (D3) x 4

Step 2: Hardware for Mounting Wall Plate

• Arm Assembly / Wall Plate (02) x 1
• Wall Plate Template (05) x 1
• Level (06) x 1
• ST8 x 90mm Lag Screw (A) x 6
• φ8 Washer (B) x 6
• Wall Anchor (C) x 6

⚠️ CAUTION: Wall Anchors (C) are for solid concrete ONLY. DO NOT use them in drywall or wood studs.

Step 4: Hardware for Front Support

• Front Support (03) x 1
• End Cap (04) x 2
• Screws (S1) x 4 (for attaching front support)

Step 6: Hardware for Adjustments

• Socket Wrench (07) x 1

STEP 1: Attach the TV Brackets to Your TV

1-1 Select TV Bolts

Choose the correct bolt diameter (M6 or M8) that threads smoothly into your TV's mounting holes. The depth of the top and bottom holes may differ.

Tip: Save the bolts that fit (M6 or M8) for Step 1-3.

1-2 Position the TV Brackets

Place the TV brackets (01) onto the back of your TV. Ensure the round holes are oriented upwards (⬆️).

1-3 Secure the TV Brackets

⚠️ WARNING:

• DO NOT turn the bolt past the bottom of the hole.
• If the bolt is too short, it may not adequately support the TV.
• If the bolt is too long, it could damage the TV.
• At least 4-5 turns into the threading is required.
• The depth of the bottom holes may be different from the top holes.
• DO NOT overtighten.

Option A: For Flat-Back TV

Use short TV bolts (C1 or D1) with washers (B1).

Option B: For Bump, Curved TV, Recessed Holes and Cables

Use long TV bolts (C2, D2, or D3) with washers (B1) and spacers (E1, E2, E3) to create extra space between the TV and brackets. You can use a tape measure to measure protruding bolts or hold spacers next to them to choose the right spacer combination. Note: There are many possible spacer combinations.

STEP 2: Mount the Arm Assembly / Wall Plate on the Wall

For mounting on wood stud walls, go to Option A (Pages 9-10).

For mounting on solid concrete, go to Option B (Pages 11-12).

Option A: For Wood Stud Installation

Tools Needed (Not Included): Electric Drill, Pencil, Tape Measure, Stud Finder, Awl, 7/32" (5.5mm) Wood Drill Bit, 1/2" (13mm) Socket Wrench.

⚠️ WARNING:

• Avoid the risk of personal injury or property damage! Tighten the lag screws (A) and washers (B) only until they are pulled firmly against the wall plate (DO NOT overtighten).
• Do not use a drill; only use a socket wrench.
• Do not use wall anchors (C) for this mounting option.

1. Find Studs and Mark Holes: Locate wood studs (max 24" / 610mm apart). Mark the center of the studs. Use the Wall Plate Template (05) and Level (06) to mark 4 hole positions on the wall.
2. Drill 4 Holes: Drill 4 holes using a 7/32" (5.5mm) drill bit to a depth of 3 1/2" (90mm).
3. Secure the Wall Plate: Attach the Arm Assembly / Wall Plate (02) to the wall using Lag Screws (A) and Washers (B). HEAVY! You may need assistance with this step. Ensure the UP arrow on the plate points upwards.

Option B: For Solid Concrete Installation

Tools Needed (Not Included): Electric Drill, Pencil, Tape Measure, Hammer, 3/8" (10mm) Concrete Drill Bit, 1/2" (13mm) Socket Wrench.

⚠️ WARNING:

• Avoid the risk of personal injury or property damage! Tighten the lag screws (A) and washers (B) only until they are pulled firmly against the wall plate (DO NOT overtighten).
• Use wall anchors (C) for this mounting option.
• Mount the arm assembly / wall plate directly on the concrete surface.

1. Mark 6 Hole Positions: Ensure the wall is at least 8" (203mm) thick. Use the Wall Plate Template (05) and Level (06) to mark 6 hole positions on the concrete wall. Note: Mark 2 upper holes near the outside of the template and 2 closest to the middle.
2. Drill 6 Holes: Drill 6 holes using a 3/8" (10mm) drill bit to a depth of 3 3/4" (95mm).
3. Tap Wall Anchors In: Insert the Wall Anchors (C) into the drilled holes.
4. Secure the Wall Plate: Attach the Arm Assembly / Wall Plate (02) to the wall using Lag Screws (A) and Washers (B) through the Wall Anchors (C). HEAVY! You may need assistance with this step. Ensure the UP arrow on the plate points upwards.

STEP 3: Verify Wall Plate is Firmly Mounted

Gently pull down on the mounted wall plate. It should feel secure and not move. If it shifts or feels loose, re-check the mounting hardware and wall type.

STEP 4: Attach the Front Support to the Arm Assembly

Attach the Front Support (03) to the Arm Assembly using four S1 screws. Then, attach the End Caps (04) to the ends of the Front Support using two S1 screws on each side.

STEP 5: Hang TV on the Front Support

HEAVY! You may need assistance with this step.

Hang the TV, with the brackets (01) attached, onto the hooks of the Front Support (03). Close the safety locks and secure them with two S4 bolts on each side.

STEP 6: Tilt Adjustment

Slightly loosen the tilt nuts (T) using the Socket Wrench (07). Tilt your TV to the desired angle. Retighten the tilt nuts (T) to hold the TV in position. NOTE: Please DO NOT overtighten or overloosen the nuts (T).

STEP 7: Level Adjustment

If it is difficult to level your TV, slightly loosen the two leveling bolts (S2) using the Socket Wrench (06). Level your TV. Retighten the leveling bolts (S2) to hold the TV in place. NOTE: Please DO NOT overtighten or overloosen the bolts (S2).