Baoli Educational Remote Control Car

Design by our hearts, bring your baby joy and happiness

Model: NO. 2405C / 2405D

Applies to: #2405C #2405D

FUNCTION INTRODUCTION

Four channel remote control
Simulated driving condition
Direction recognition
Alarm recognition
Shifting Gear

PICTURE OF EACH PART

Remote sensitive control: High simulation design, used for remote control of the car. It helps babies develop hand-eye coordination and spatial perception, experiencing the charm of technology.

Components:

Steering handle
Forward/backward control
Turn left/right control
Steer control
ON/OFF switch
Volume +/-
Light button
Horn button
Speed gear
Power Indicator
Indicator lamp for turn-left
Indicator lamp for turn-right
Fire truck sound button
Ambulance sound button
Police car sound button

FUNCTIONAL EXPLANATION

正面 (Front View):

The cyclic rotary scene: Your baby can control the car to drive along the road using the steering wheel. The steering wheel controls the car's movement left or right.
ON/OFF: High-simulated key for the car. Rotate the knob to produce engine sound. Volume can be adjusted.
Sound Buttons: Pressing the buttons for fire truck, ambulance, or police car will play the corresponding alarm sound with flashing traffic lights.

背面 (Back View):

Turn-right: When the handle is toggled upward, the right steering light flashes.
Turn-left: When the handle is toggled downward, the left steering light flashes. When the handle is in the middle, the direction light is off.
Simulated operating by shifting the gear: The rotating speed of the scene slows down when shifting gears, providing a more realistic driving experience.
Gear 0: Neutral Gear, Stop driving.
Gear 1: Slow Speed.
Gear 2: Fast Speed.

Remote control Battery installation diagram

Open the battery cover on the Remote control back. Load 2PCS DC1.5V AA batteries into the battery compartment. Securely buckle the battery cover and then lock with screws.

Note: the positive and negative poles of the battery should not be misplaced!

Explanation of charging function

This toy uses a 3.7V lithium battery, which is non-replaceable. Connect the charging cable to the charging hole to charge. The red light shines through the small round hole when charging and goes out when full (charging time is about 150 minutes). Note: It cannot play normally during charging. It can be played normally only after the charging cable is removed from the power supply.

The toy shall only be used with a power supply for toys; the USB power supply is not a toy.

This toy contains battery that is non-replaceable.

USB charger used with the electric toy shall be regularly examined for damage to the supply cord, plug, enclosure or other parts, and in the event of damage, it shall not be used until the damage has been repaired.

This toy is only to be connected to equipment bearing either of the following symbols: ⏚ ⏚

Notes: After 90 seconds of inactivity, it will play music automatically, which means it switches to sleep mode. You can press any key to wake it up.

Safety Warnings

Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types).
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
And a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

FCC Compliance Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.