Aftermarket ATV-UTV Parts and Accessories
Instruction Manual for SUPERATV models including: IN-ROOF-P-RAN1KXP Polaris Ranger 1000 Aluminum Roof, IN-ROOF-P-RAN1KXP, Polaris Ranger 1000 Aluminum Roof, 1000 Aluminum Roof, Aluminum Roof, Roof
Polaris Ranger 1000 Aluminum Roof
File Info : application/pdf, 6 Pages, 618.44KB
DocumentDocument2753 Michigan Road · Madison, Indiana 47250 · 855-743-3427 INSTALLATION INSTRUCTIONS Roof: for Polaris Ranger® XP 1000 - Do not discard packaging until product has been successfully installed. - SuperATV does not recommend keeping Roof installed while transporting on an open air trailer. Remove or secure with straps. Roof Rear Foam Flat When installing components, do not tighten any hardware completely unless noted. Liability Statement SuperATV's® products are designed to best fit user's ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV's® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact SuperATV® to verify that they will work together. Although SuperATV® has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product's ability to protect user from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing SuperATV® products, user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers' products will not be covered by SuperATV®. SuperATV® parts and products are not warrantied if item was not installed properly, misused, or modified. Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you. The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof. Need help with your installation? sales@superatv.com www.superatv.com 1-855-743-3427 © 2022 SuperATV.com®. All Rights Reserved. 8:00am - 8:00pm EST M-Th 8:00am - 7:00pm EST Friday 9:00am - 2:00pm EST Saturday Read instructions and view illustrations before beginning. Thank You For Choosing IN-ROOF-P-RAN1KXP 4/8/2022 - Install provided Foam to Frame. Foam Foam (driver side) IN-ROOF-P-RAN1KXP 2 - Install Flat to inside of Roof along back edge. IN-ROOF-P-RAN1KXP Flat 3 - Place Short Spacers in line with holes in Frame. 3x - Short Spacer IN-ROOF-P-RAN1KXP (driver side) 4 - Secure Rear and Roof to machine with hardware shown. 4 each M8 x 60mm M8 Nut 2 each M8 x 30mm M8 Nut 4x - Long Spacer 2 each M5 x 20mm M5 Nut - Secure Roof to machine with hardware shown. 3 each M6 x 25mm M6 Nut - Align Roof to machine and tighten all hardware. IN-ROOF-P-RAN1KXP 6