Instruction Manual for ContentSpeed models including: 35FVX003 Smart Charging Pile AC EV Charge, 35FVX003, Smart Charging Pile AC EV Charge, AC EV Charge, EV Charge, Charge, Smart Charging Pile, Charging Pile, Pile
Read this manual completely and master the safety matters related to operation. caveat. If the charging gun or charging cable is damaged:.
Oct 10, 2022 — caveat. In case of emergency: • Press the emergency stop button. • Contact the charging operation staff immediately. • Take action according to the ...
Smart charging pile Operating instructions BSEC - AC EV charge Display or no screen · Read this manual completely and master the safety matters related to operation. caveat If the charging gun or charging cable is damaged: · Do not use, stop using immediately · Contact the charging operation staff immediately caveat In case of emergency: · Press the emergency stop button · Contact the charging operation staff immediately · Take action according to the emergency measures of the owner or charging operator caveat If operating after injury, accident, typhoon, accident or disaster, please observe: · Are there any flames or smoke inside and outside the charger? · Whether the charger has been soaked in water, whether there are other liquids and traces · Whether the charger is damaged due to other reasons If any of the above conditions occur, please stop charging immediately and contact the charging operator caveat Charge gun lock During the charging process, the charging gun will be locked to the socket of the charging vehicle. It cannot be pulled out before charging is stopped. Strong pulling is prohibited. Strong pulling with more than 1000N may damage the locking mechanism and risk arcing. Note Gun insertion and drawing: · Take the gun carefully and insert the gun, do not drop and bump · Pull out the gun carefully and put the charging cable and the charging gun back in place · Only applicable to national standard interface electric vehicles 1 AC Charging Pile Incoming Current (Circuit Breaker )and CABLE specification Number Charger Specification(KW) 1 Single phase AC One Gun 3.5 2 Single phase AC One Gun 7 3 Three phase AC One Gun 11 4 Three phase AC One Gun 22 5 Three phase AC One Gun 43 6 Single phase AC Two Gun 3.5+3.5 7 Single phase AC Two Gun 7+7 8 Three phase AC Two Gun 11+11 9 Three phase AC Two Gun 22+22 10 Three phase AC Two Gun 43+43 Incoming Current (Circuit Breaker) Type 20A/2P 40A/2P 20A/4P 40A/4P 80A/4P 40A/2P 80A/2P 40A/4P 80A/4P 160A/4P Cable Specification 3×4mm² 3×6mm² 5×4mm² 5×6mm² 5×16mm² 3×6mm² 3×16mm² 5×6mm² 5×16mm² 3×35mm²+2×16mm² 2 Charging process steps Step 1 Remove the charging gun from the charging pile and connect it to the car charging port. Step 2 After the charging pile is powered on, there is a waiting time of 10 seconds. After 10 seconds, it enters the main charging page. The UI is as follows Display internal temperature Gun status: no gun inserted (not ready for charging) Gun status: plug in the gun (ready for charging) The network is not connected Program Version 1 gun 3 Step 3 Move the charging card to an area closer to the card. After successfully swiping the card, the charging indicator will light up. Wait for the vehicle communication to complete and start charging. The UI interface is as follows: Step 4 End charging When the battery is fully charged, the charging lamp goes out and the charging is finished, pull the charging gun out of the vehicle and insert it into the charging pile gun seat. Stop charging by swiping the card, the charging light goes out, and the charging is finished. Pull the charging gun out of the car and insert it into the charging pile gun seat. The interface is as follows: Transaction Charged Power Total Charging Time finished charging Transaction number KWH Charging time 4 Report an error If there is a fault alarm during charging, the fault indicator will always be on. The UI interface is as follows: An error occurred Please refer to common exception handling methods (The error light is always on when an error occurs) Charger failure out of service Display the error code, you can check the error code table Common exception handling NO unusual phenomenon . Defective power 1 light 2 The fault light is always on. 3 No response when swiping 4 Charging failed possible reason Solution The power cord is not connected The light cable is not connected Open trip Emergency stop switch is pressed The charging card is not near the swiping position Magnetic card failure or damage The charging gun is not plugged in Check the power line again by the installer Check the lamp line again by the installer Reset MCB Reset the emergency stop button by turning it clockwise Remove the card first, and then close to the swipe area again, do not move the card up, down, left, or right Please contact the customer service center to replace the card (man-made damage requires paid replacement card) Reconnect the charging gun to ensure that the gun head is in place; check whether there is an error light on the charging pile; check whether the buttons on the upper part of the charging gun are in a natural state; try to restart the charging pile after power off. 5 Vehicle itself Go to the 4S shop to investigate the vehicle's own problems. error code 0X4 0X5 0X6 0X7 0X8 0X9 0XA 0X20 0X21 0X22 0X23 0X24 Error alarm information Memory error shutdown Screen communication timeout and shutdown Leakage shutdown Main board temperature shutdown Overtime shutdown in the background Charging timeout 99h59m59 timeout Door switch Emergency stop Meter timeout CP communication Grid fluctuation Relay failure solution Power off and restart, if the fault cannot be recovered, please contact the operator or equipment manufacturer customer service Power off and restart, if the fault cannot be recovered, please contact the operator or equipment manufacturer customer service Please check the charging pile, if in the normal range, contact the operator or equipment manufacturer customer service Please check the internal temperature of the charging pile, if it is within the normal range, contact the operator or equipment manufacturer customer service Please check the charging pile and network, if in the normal range, contact the operator or equipment manufacturer customer service Power off and restart, if the fault cannot be recovered, please contact the operator or equipment manufacturer customer service Please check whether the rear door of the charging pile is closed, if in the normal range, contact the operator or equipment manufacturer customer service. When the emergency stop is pressed, turn the emergency stop switch to the right to recover. 18 If the emergency stop is restored, it will report the fault and contact the operator or equipment manufacturer customer service. Power off and restart, if the fault cannot be recovered, please contact the operator or equipment manufacturer customer service Please check whether the on-board charger is faulty. If the on-board charger is in the normal range, contact the operator or equipment manufacturer's customer service. If the AC voltage is lower or higher than 230V ±10% (or 15%), check the input voltage range, and contact the operator or equipment manufacturer customer service if it is within the normal range. Power off and restart. If the fault cannot be 6 0X25 0X26 0X27 0X28 Temperature failure shutdown overcurrent Gun temperature is too high Ground Fault recovered, please contact the operator or the equipment manufacturer's customer service. Please check the internal temperature of the charging pile, if it is within the normal range, contact the operator or equipment manufacturer customer service. Check whether the on-board charger is faulty. If the on-board charger is in the normal range, contact the operator or equipment manufacturer's customer service. Please check the internal temperature of the charging pile, if it is within the normal range, contact the operator or equipment manufacturer customer service. Please check the ground connection, if in the normal range, contact the operator or equipment manufacturer customer service. 7WPS 文字