2012-2015 Versa and Sentra; CVT Valve Body Replacement With Confirmed DTC
Previous preliminary number: 1502042
Technical, Communications
CHRISG2 Nissan
2012-2015 Versa and Sentra; CVT Valve Body Replacement ...
manual plate . CAUTION: To remove nut, fix manual plate with flat-blade screwdriver (B). 10. Press the CVT unit harness connector into the transaxle case. CAUTION: Never damage the CVT unit harness connector. NOTE: Clean around the CVT unit harness connector to prevent foreign materials from entering into the transaxle case. 11.
Classification:
AT15-003f
Reference:
NTB15-037f
Date:
August 10, 2018
VERSA SEDAN, VERSA NOTE, AND SENTRA; CVT VALVE BODY REPLACEMENT WITH CONFIRMED DTC
This bulletin has been amended. A TCM P/N was added to 2015 Sentra in Table A. No other changes were made. Discard all previous versions of this bulletin.
APPLIED VEHICLES:
2012 2017 Versa Sedan (N17) 2014 2017 Versa Note (E12) 2013 2017 Sentra (B17)
APPLIED TRANSMISSION: CVT (RE0F11A)
NOTE: Does not apply to 2017 Sentra equipped with MR16DDT turbo engine.
IF YOU CONFIRM
If one or more of the DTCs listed in the DTC Chart on page 2 are present in the Transmission Control Module (TCM).
And No other DTCs are present other than what are listed in the DTC Chart.
ACTION
1. Go to Repair Overview on page 3 to determine which repairs to perform to the applied vehicle being worked on.
IMPORTANT: The purpose of "ACTION" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service Procedure as it contains information that is essential to successfully completing the repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/40
DTC Chart
DTC CODE
P0711 P0712 P0713 P0740 P0743 P0846 P0847 P0848 P0962 P0963 P0998 P0999 P0966 P0967 P099B P099C
DTC/CIRCUIT DIAGNOSIS
TRANSMISSION FLUID TEMPERATURE SENSOR A TRANSMISSION FLUID TEMPERATURE SENSOR A TRANSMISSION FLUID TEMPERATURE SENSOR A TORQUE CONVERTER TORQUE CONVERTER TRANSMISSION FLUID PRESSURE SEN/SW B TRANSMISSION FLUID PRESSURE SEN/SW B TRANSMISSION FLUID PRESSURE SEN/SW B PRESSURE CONTROL SOLENOID A PRESSURE CONTROL SOLENOID A SHIFT SOLENOID F SHIFT SOLENOID F PRESSURE CONTROL SOLENOID B PRESSURE CONTROL SOLENOID B SHIFT SOLENOID G SHIFT SOLENOID G
2/40
NTB15-037f
Repair Overview
Applied Vehicle has one or more DTCs in
the DTC Chart
All Applied Vehicles: Replace the control valve
assembly (valve body)
Repairs in addition to valve body replacement:
2013-2017 Sentra 2014-2017 Versa NOTE 2013-2017 Versa Sedan
Reprogram the TCM
2012 Versa Sedan
Erase Memory Data Conform CVTF Deteriortn Auxiliary gearbox clutch
point learning
END
3/40
NTB15-037f
SERVICE PROCEDURE
OIL PAN, CONTROL VALVE (Valve Body)
Exploded View
1. Transaxle assembly 4. Manual plate
7. Strainer
10. Oil pan 13. Overflow tube
: Apply petroleum jelly
2. O-ring 5. Washer 8. Oil pan gasket 11. Drain plug gasket
: Always replace after every disassembly. : Apply CVT fluid
: Nm (kg-m, ft-lb)
: Nm (kg-m, in-lb.)
Valve Body: Removal and Installation
REMOVAL
1. Disconnect battery negative terminal. 2. Remove engine under cover.
4/40
JSDIA6707GB
3. Control valve 6. O-ring 9. Magnet 12. Drain plug
NTB15-037f
3. Disconnect the CVT unit harness connector. 4. Remove the drain plug and overflow tube, and then drain the CVT fluid.
CAUTION: Use caution when looking into the drain hole as there is the risk of fluid entering the eye. 5. Remove the drain plug gasket from the drain plug. 6. Remove the oil pan mounting bolts ( ), and then remove the oil pan and oil pan gasket.
: Vehicle front
7. Remove the magnets from the oil pan. Clean magnets. Clean CVT oil pan. Reinstall magnets to the oil pan.
8. Remove the strainer bolts , and then remove the strainer from the control valve.
Discard the strainer. A new one will be used during assembly.
9. Remove the nut and washer , and then remove manual plate . CAUTION: To remove nut, fix manual plate with flat-blade screwdriver (B).
10. Press the CVT unit harness connector into the transaxle case. CAUTION: Never damage the CVT unit harness connector. NOTE: Clean around the CVT unit harness connector to prevent foreign materials from entering into the transaxle case.
11. Remove the control valve bolts , and then remove the control valve from the transaxle case. CAUTION: · Never drop the control valve and manual valve.
5/40
NTB15-037f
INSTALLATION
1. Install the control valve, and then tighten control valve bolts to the specified torque.
CAUTION:
· Never pinch the harness between the control valve
and the transaxle case. · Never drop the control valve and manual valve.
2. Install the manual plate and washer , and then tighten nut to the specified torque. CAUTION: To tighten nut, fix manual plate with flat-blade screwdriver. Reassembly Torque: 22.1 N·m (2.3 kg-m, 16 ft-lb)
3. Install the new strainer , and then tighten the strainer bolts to the specified torque.
4. Install oil pan (with oil pan gasket) to transaxle case and temporarily tighten oil pan bolts ( ). CAUTION: Never reuse oil pan gasket.
: Vehicle front
5. Tighten the oil pan bolts to specification in the order shown.
: Vehicle front
6. Tighten the overflow tube to the specified torque. CAUTION: If it is not tightened to the specified torque, the tube may be damaged.
7. Connect the CVT unit harness connector. 8. Connect battery negative terminal. 9. Fill with CVT fluid from overflow tube to the specified level.
Refer to ESM for further information. 10. Install the drain plug and drain plug gasket to oil pan.
CAUTION: Never reuse drain plug gasket.
11. Reinstall engine under cover.
6/40
NTB15-037f
TCM Reprogramming IMPORTANT: Before starting the TCM reprogram procedure, make sure:
ASIST on the CONSULT PC has been synchronized (updated) to the current date.
All CONSULT-III plus (C-III plus) software updates (if any) have been installed. NOTE:
TCM reprogramming applies to 2014-2017 Versa NOTE, 2013-2017 Sentra, and 2013-2017 Versa Sedan only.
2012 Versa Sedan does NOT require reprogramming. For more information, see Repair Overview on page 3.
1. Connect the plus Vehicle Interface (plus VI) to the vehicle. CAUTION: Make sure the plus VI is securly connected. If the plus VI connection is loose during reprogramming, the process will be interrupted and the TCM may be damaged.
2. Connect the AC Adapter to the CONSULT PC. CAUTION: Be sure to connect the AC Adapter. If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted and the TCM may be damaged.
3. Connect the GR8, set to "Power Supply" mode, to the vehicle battery. CAUTION: Be sure the GR8 is connected securely to the battery. Make sure the battery voltage stays between 12.0V and 15.5V during reprogramming. If the battery voltage goes out of this range during reprogramming, the TCM may be damaged.
4. Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range of the CONSULT PC and the VI. CAUTION: Make sure to turn OFF all external Bluetooth® devices. If Bluetooth® signal waves are within range of the CONSULT PC and the VI during reprogramming, reprogramming may be interrupted and the TCM may be damaged.
5. Turn the ignition ON with the engine OFF.
The engine must not start or run during the reprogramming procedure.
6. Turn OFF all vehicle electrical loads such as exterior lights, interior lights, HVAC, blower, rear defogger, audio, NAVI, seat heater, steering wheel heater, etc.
IMPORTANT: Make sure to turn OFF all vehicle electrical loads. Make sure the battery voltage stays between 12.0V and 15.5V during reprogramming. If the battery voltage goes out of this range during reprogramming, the TCM may be damaged.
7. Turn ON the CONSULT PC.
8. Select/open C-III plus.
7/40
NTB15-037f
9. Wait for the plus VI to be recognized. Serial number will display when the plus VI is recognized.
Step 9: plus VI is recognized
Figure 1 10. Select Re/programming, Configuration.
Figure 2
8/40
Step 10
NTB15-037f
11. Use arrows (if needed) to view and read all precautions. 12. Check the box confirming the precautions have been read. 13. Select Next.
Step 12
Figure 3
Step 11
Step 13
14. If the screen in Figure 4 displays, select Automatic Selection(VIN). If the screen in Figure 4 does not display, skip to step 15.
Step 14
Example
Figure 4
9/40
NTB15-037f
15. Make sure VIN or Chassis # matches the vehicle's VIN. 16. If the correct VIN is displayed, select Confirm.
Step 15: Verify here
17. Select Confirm.
Step 16
Figure 5
Figure 6
10/40
Step 17
NTB15-037f
18. Select TRANSMISSION.
Step 18
19. Select Reprogramming.
Figure 7
Step 19
Figure 8
11/40
NTB15-037f
20. Follow the on-screen instructions; maintain the following conditions: a. Ignition ON, with the engine OFF. b. Press the Brake. c. Press accelerator between ¼ and ½. d. Put shift selector in R.
21. Select Start.
Step 21
Figure 9 22. When COMPLETED is displayed, select Next.
Step 22
Figure 10
12/40
NTB15-037f
23. Operate the ignition per the on screen instructions.
Ignition status Timer Progress display
Figure 11 24. When OK is displayed, select Next.
Step 24
Figure 12
13/40
NTB15-037f
25. Move the shift selector to P, then select Next.
Step 25
Figure 13
26. Operate the shift selector per the on-screen instructions. a. Move the shift selector; P>R>N>D>P b. Confirm the center display meter indicates the correct selector position.
27. Select Next.
Step 26
Figure 14
14/40
Step 27
NTB15-037f
28. Find the TCM Part Number (see Figure 15) and write it on the repair order.
NOTE: This is the current Part Number (P/N).
Step
29. Compare the P/N you wrote
28
Step 31
down to the numbers in the
Current TCM Part Number
column in Table A below.
Figure 15
30. Comparison results:
If there is a match, continue with the reprogramming procedure.
If there is not a match, reprogramming is not needed. Skip to ERASE MEMORY DATA on page 29.
Table A
MODEL
MODEL YEAR
CURRENT TCM PART NUMBER: 31036 -
Sentra Versa Sedan Versa NOTE
2013
2014
2015
2016 2017 2013 2014 2015 2016 2017 2014 2015 2016 2017
3SG0A, 3SG0B, 3SG0C, 3SG9B, 3SG9C, 3SR0A, 3SR0B, 3SR0C, 3SR9B, 3SR9C 9AM2A, 9AM2B, 9AM2C, 9AM9B, 9AM9D, 9AM9E
4AT0A, 4AT0B, 4AT0C, 4AT0D, 4AT9A, 4AT9D, 4AT8E, 4AT9E
4AF6A, 4AF6B, 4AF9D 4FY0A, 4FY0B, 4FY0C 9KB1B, 9KB1C, 9KB1D, 9KB9E, 9KJ9E
3BE0A, 3BE0B, 3BE9A, 3BE9C 9KE0A, 9KE0B, 9KE0C, 9KE9C, 9KE9E 9KN0A, 9KN0B, 9KN0C, 9KN8D, 9KN8E
9KN2A, 9KN2B, 9KN2C 3VB2A, 3VB2B, 3VB2C, 3VB8C, 3VB9D 3VB6A, 3VB9A, 3VB9B, 3VB9C, 3VB9E, 3WC9D
3VB4A, 3VB4B, 3VB4C, 3VB4D, 3VB7A, 3WC9E 9ME0A, 9ME0B, 9ME0C
31. Select Save.
15/40
NTB15-037f
32. Use arrows (if needed) to view and read all precautions. 33. Check the box confirming the precautions have been read. 34. Select Next.
Step 33
Figure 16
Step 32
Step 34
NOTE: If you get the screen in Figure 17 and it is blank (no reprogramming listed), it means there is no reprogramming available for this vehicle. Close C-III plus and refer back to ASIST for further diagnosis.
TRANSMISSION
Figure 17
16/40
NTB15-037f
35. Read the Current Part Number and Part Number After Reprogramming. They should be different.
36. Select Next.
Step 35 These numbers
should be different
Step 36
Figure 17a
17/40
NTB15-037f
37. Make sure OK is highlighted green (battery voltage must be between 12.0 and 15.5 Volts).
38. Select Next. IMPORTANT: Battery voltage must stay between 12.0 and 15.5 Volts during reprogramming or TCM reprogramming may be interrupted and TCM may be damaged.
Monitor battery voltage here
Step 37
Figure 18
Step 38
39. Make sure OK is highlighted green for all Judgements then select Start.
Monitor battery voltage here
EXAMPLE
Figure 19
18/40
Step 39
NTB15-037f
40. Select USA/CANADA Dealers. 41. Select OK.
Step 40
Step 41
Figure 20 NOTE: The above screen may not display if the CONSULT PC has remained ON since the
last reprogramming. If the CONSULT PC is not connected to the Internet, the screen in Figure 21 will
display.
Figure 21
19/40
NTB15-037f
42. Enter Username and Password.
Before reprogramming will start, you will be required to enter your User Name and Password.
The CONSULT PC must be connected to the Internet (Wi-Fi or cable). If you do not know your User Name and Password, contact your Service Manager.
43. Select Submit. There will be a short pause while the username and password are authenticated. Once authentication completes, TCM reprogramming will automatically begin and the screen in Figure 23 on the next page will be displayed.
Step 43
Step 42
Figure 22
20/40
NTB15-037f
44. Wait for both progress bars to complete.
Step 44
Figure 23 45. When the screen in Figure 24 displays, the reprogramming is complete.
NOTE: If the screen in Figure 24 does not display (which indicates reprogramming did not complete), refer to the information on the next page. 46. Disconnect the battery charger (GR8) from the vehicle. 47. Select Next.
Step 47
Figure 24
NOTE: Additional steps/operations are required before C-III plus will provide the final reprogramming confirmation report. Continue with the reprogramming procedure on page 23.
21/40
NTB15-037f
If reprogramming does not complete and the "!?" symbol displays as shown in Figure 25:
Check battery voltage (12.0 15.5V).
Ignition ON, engine OFF.
External Bluetooth® devices are OFF.
All electrical loads are OFF.
Select Retry and follow the on screen instructions.
NOTE: Retry may not go through on first attempt and can be selected more than once.
Figure 25
If reprogramming does not complete and the "X" symbol displays as shown in
Figure 26:
Do not disconnect the plus VI or shut down C-III plus if reprogramming does not complete.
Check battery voltage (12.0 15.5V).
CONSULT A/C adapter is plugged in.
Ignition ON, engine OFF.
Transmission in Park.
All C-III plus / plus VI cables are securely connected.
All C-III plus updates are installed.
Select Home, and then restart the reprogram procedure from the beginning.
Figure 26
22/40
NTB15-037f
48. Confirm the Transmission Fluid temperature judgment is OK, then select Next.
If the judgment is NG, drive the vehicle to warm the transmission until the judgment changes to OK.
Step 48
Figure 27
23/40
NTB15-037f
49. Follow the on-screen instructions; maintain the following conditions:
a. Parking brake set. b. Ignition ON, with the
engine OFF. c. Press the Brake. d. Press accelerator
between ¼ and ½. e. Put shift selector in
R.
50. Select Erase DTC.
51. Follow the on-screen instructions; maintain the following conditions: a. Parking brake set. b. Ignition ON, with the engine OFF. c. Fully depress the accelerator. d. Put shift selector in R.
52. Select Start.
Step 50
Figure 28
Step 52
Figure 29
24/40
NTB15-037f
53. When COMPLETED is displayed, select Next.
Step 53
Figure 30
54. Operate the ignition per the on-screen instructions.
Ignition status Timer Progress display
Figure 31
25/40
NTB15-037f
55. When OK is displayed, select Next.
Step 55
Figure 32
56. Operate the shift selector per the on-screen instructions. a. Move the shift selector to P; then move P>R>N>D>P b. Confirm the center display meter indicates the correct selector position.
57. Select Next.
Step 56
Figure 33
Step 57
26/40
NTB15-037f
58. Erase all DTCs as follows: a. Turn the ignition OFF. b. Turn the Ignition ON. c. Wait for DTC erase to complete.
59. Select Next.
Turn ignition ON > OFF > ON ON
Step 59
Figure 34
27/40
NTB15-037f
60. Verify the before and after part numbers are different. 61. Print a copy of this screen (Figure 35) and attach it to the repair order. 62. Select Confirm.
Step 60
Step 61
Step 62
Figure 35
NOTE: If you cannot print the above screen: a. Select Screen Capture. b. Name the file. c. Save the file in My Documents. A copy of the screen is now saved in the CONSULT PC. It can be retrieved and printed at a later time.
28/40
NTB15-037f
ERASE MEMORY DATA NOTE: This procedure is for all Applied Vehicles. 63. Navigate C-III plus to the screen shown in Figure 36.
Diagnosis (All Systems) > TRANSMISSION > Work support
64. Select ERASE MEMORY DATA.
65. Select Start.
Step 64
Figure 36
Step 65
29/40
NTB15-037f
66. Follow the on-screen instructions; maintain the following conditions: a. Parking brake set. b. Ignition ON, with the engine OFF. c. Fully depress the accelerator. d. Put shift selector in R.
67. Select Start.
68. When the Current status changes to COMPLETED, select End.
Step 67
Figure 37
Step 68
Figure 38
69. Move the shift selector to P, and then turn the ignition OFF. 70. Turn the ignition ON, and then confirm P and N display by moving the shift selector in
those positions.
30/40
NTB15-037f
CONFORM CVTF DETERIORTN NOTE: This procedure is for all Applied Vehicles.
71. Navigate C-III plus to the screen shown in Figure 39. Diagnosis (All Systems) > TRANSMISSION > Work support
72. Select CONFORM CVTF DETERIORTN. 73. Select Start.
74. Select Start.
Step 72
Figure 39
Step 73
Figure 40
31/40
Step 74
NTB15-037f
75. Select Clear.
Step 75
76. Select Yes.
Figure 41
Step 76
Figure 42
32/40
NTB15-037f
77. When CVFT DETERIORATION DATE changes to "0", select End.
0
Step 77
Figure 43 78. Start the engine. 79. Set the parking brake. 80. Turn OFF the A/C. 81. Bring the engine to normal operating temperature range. 82. Confirm the CVT fluid temperature is over 122°F (50°C).
33/40
NTB15-037f
Auxiliary gearbox clutch point learning NOTE: This procedure is for all Applied Vehicles.
83. Navigate C-III plus to the screen shown in Figure 44. Diagnosis (All Systems) > TRANSMISSION > Work support
84. Select Auxiliary gearbox clutch point learning. Or If this feature is not available in the vehicle that is being repaired, skip to Manual Auxiliary gearbox clutch point learning on page 38.
85. Select Start.
Step 84
Figure 44
Step 85
34/40
NTB15-037f
86. Follow the on-screen instructions in Figure 45, and then select Start.
Step 86
Figure 45 87. With the brake pedal still applied, shift the CVT selector lever into the D position.
Figure 46 (below) will be displayed after shifting into D position. NOTE: The Current status will show EXECUTING (Figure 46), but until the vehicle is shifted into the D position, Auxiliary gearbox clutch point learning will not begin.
Step 87
Figure 46
35/40
NTB15-037f
88. Continue to depress the brake pedal until the Current status shows "Completed" as shown in Figure 48 at the bottom of this page.
NOTE: This may take several minutes to complete.
Figure 47 89. When Completed is displayed, select End.
Step 89
Figure 48
90. Shift the vehicle into "P", turn ignition OFF and release the brake pedal. 91. Perform Auxiliary Gearbox Clutch Point Learning (steps 83 to 89) one additional time
(a total of two times).
36/40
NTB15-037f
Erase DTCs NOTE: This procedure is for all Applied Vehicles. 92. Use C-III plus to erase any transmission DTCs that may have stored. 93. Turn OFF C-III plus. 94. Disconnect C-III plus and the plus VI from the vehicle. 95. Verify the CVT operates normally and no abnormal noises are heard during a test drive.
37/40
NTB15-037f
MANUAL AUXILIARY GEARBOX CLUTCH POINT LEARNING
CAUTION: If clutch touch point learning is not performed, you may feel shift shock when the auxiliary transmission shifts.
NOTE: This manual procedure is only needed if the auto procedure is not available in C-III plus.
a. Start the engine and warm up the CVT fluid to 50°C (122°F). NOTE: Confirm the CVT fluid temperature by "FLUID TEMP" in "Data Monitor".
b. Turn the air conditioner OFF. c. Shift the CVT selector lever to the P position, turn the ignition OFF and then wait for
5 seconds. d. Start the engine and allow it to idle for 5 seconds. e. Turn the ignition OFF and then wait for 30 seconds. f. Perform Step "e" to Step "f" two more times (Total: Three times). g. Start the engine. h. Allow engine to idle for 30 seconds. i. Shift the CVT selector lever to D position. j. Accelerate the vehicle from 0 km/h (0 MPH) to 65 km/h (40 MPH) at low throttle
(0.5/8 1/8). k. Decelerate the vehicle to 30 km/h (18 MPH) or less without using brakes. l. Stop the vehicle and shift the selector lever to P position. m. Turn the ignition OFF and wait for 5 seconds or more. n. Restart the engine. o. Perform Step "j" to Step "o" four times (Total: Five times). p. Shift the selector lever to D position. q. Accelerate the vehicle from 0 km/h (0 MPH) to 45 km/h (28 MPH) at low throttle
(0.5/8 1/8). r. Stop the vehicle and shift the selector lever to P position. s. Turn the ignition OFF for 5 seconds or more and then restart the engine. t. Perform Steps "q" to Step "t" four times (Total: Five times). u. Drive the vehicle and check that no shock occurs while shifting gears.
38/40
NTB15-037f
PARTS INFORMATION
All Vehicles
DESCRIPTION
PART #
QUANTITY
GASKET (CVT drain plug)
NS-3 CVT Fluid (All vehicles listed below except
2012 MY Versa Sedan)
11026-JA00A 999MP-NS300P (1)
1 as needed
NS-2 CVT Fluid (2012 MY Versa Sedan only) 999MP-NS200P (1) as needed
(1) NS-2 and NS-3 CVT Fluids can be ordered through the Nissan Maintenance Advantage program: Phone: 877-NIS-NMA1 (877-647-6621). Website order via link on dealer portal www.NNAnet.com and click on the "Maintenance Advantage" link.
Versa Sedan MY 2013-2017 and Versa NOTE MY 2014-2017
DESCRIPTION
PART #
KIT-CONTROL VALVE
3170E-X428B
Kit Includes
VALVE ASSY - CONTROL
- -
GASKET - OIL PAN
- -
STRAINER ASSY-OIL
- -
Versa Sedan MY 2012
DESCRIPTION VALVE ASSY - CONTROL
STRAINER ASSY-OIL GASKET - OIL PAN
PART # 31705-3JX8A 31728-3JX0B 31397-3JX0A
Sentra MY 2013-2017 DESCRIPTION
KIT-CONTROL VALVE Kit Includes
VALVE ASSY - CONTROL GASKET - OIL PAN
STRAINER ASSY-OIL
PART # 3170E-X428C
--- -
QUANTITY 1
1 1 1
QUANTITY 1 1 1
QUANTITY 1
1 1 1
39/40
NTB15-037f
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
OPERATION
PFP
OP CODE SYM DIAG FRT
Replace Control Valve
(1)
JD48AA HC 32 (2)
(1) Refer to the Electronic Parts Catalog (FAST) and use the applicable Control Valve Assembly Part Number (31705-*****) as the Primary Failed Part.
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated flat rate time.
And if needed on the same line
OPERATION
OP CODE
FRT
Reprogram TCM
JE99AA
(1)
(1) Reference the current Nissan Warranty Flat Rate Manual and use the indicated flat rate time.
40/40
NTB15-037f
Nissan CVT Judder Repair Guide: Sentra & Versa Models Comprehensive technical bulletin for diagnosing and repairing CVT judder issues in 2013-2017 Nissan Sentra and 2014-2017 Versa Sedan/Note vehicles. Covers diagnostic trouble codes (DTCs), fluid checks, debris inspection, and component replacement procedures.
2025 Nissan Versa Owner's Manual and Maintenance Information Comprehensive owner's manual for the 2025 Nissan Versa, covering operation, maintenance, safety features, and technical information. Includes details on safety systems, controls, driving, emergency procedures, and care.
Nissan CVT Service Bulletin: Control Valve and Transaxle Replacement Procedures This Nissan Service Bulletin (NTB17-041) provides detailed instructions for technicians on the additional service required after replacing a Continuously Variable Transmission (CVT) control valve or transaxle assembly for 2013-2017 Sentra, Versa Note, and Versa models. It covers procedures using CONSULT-III plus, including erasing calibration data, learning values, and performing clutch point learning.
Nissan Technical Bulletin NTB18-077: MIL ON with DTC P0776, P1715 - Hesitation and Lack of Power Nissan technical bulletin NTB18-077 addressing MIL ON with DTC P0776, P1715, causing hesitation and lack of power in specific Sentra, Rogue Sport, NV200, and Taxi models equipped with CVT (RE0F10D) transmission. Details diagnosis, repair flow, valve body inspection, CVT belt inspection, TCM reprogramming, and additional service procedures.
Nissan Infotainment Software Update Guide for Technicians This Nissan Technical Service Bulletin (NTB23-018B) provides essential instructions for qualified technicians to update the infotainment software in various Nissan vehicle models, addressing stability improvements and bug fixes.
Nissan Infotainment Software Update Technical Service Bulletin This Nissan Technical Service Bulletin provides instructions for technicians on updating infotainment system software for various Nissan vehicle models to improve stability and fix bugs.
