Follow the instructions on pages 5 & 6 for bottle preparation. Press selected insert into bottom of Measuring Wheel. Inserts are numbered 1, 3, 4 and 5. Do not use the Measuring Wheel without an insert. 4 With Powder Container assembled follow these steps to rinse internal parts. Assemble: Rinse internal parts: don’t add powder. 3 4
See separate Silicone Scraper instructions for more details. ... The Formula pro is now ready to use. Follow the instructions on pages 5 & 6 for bottle preparation.
Please visit www.babybrezza.com For tips, accessory products and more. Formula Pro® ® This product may be covered under one or more of the following including U.S. Patent No. 8,584,901 and pending patent application(s) in the U.S. and other countries. ©2014 Baby Brezza Enterprises LLC Instructions Important Safeguards When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions before using. 2. Do not touch hot surfaces. 3. To protect against electric shock and injury to persons do not immerse cord, plug, water tank or appliance in water or other liquid. 4. Close supervision is necessary when any appliance is used by or near children. 5. Unplug from outlet when not in use and before cleaning. Allow to cool before inserting or removing parts, and before cleaning the appliance. 6. Do not operate this appliance with a damaged cord or plug. If the appliance malfunctions or has been damaged in any manner, Return appliance to the nearest authorized service facility for examination, repair or adjustment. 7. The use of accessory attachments not recommended by the appliance manufacturer may cause re, electric shock or injury. 8. Use on level surface and be sure there is no debris under the unit and the rubber pads are touching the surface. 9. Household use only. Do not use outdoors. 10. Do not let cord hang over edge of table or counter, or touch hot surfaces. 11. Do not place on or near hot gas or electric burner, or in a heated oven. 12. Do not use appliance for other than intended use. 13. Do not attempt to use the machine without water in the water tank. 14. This appliance has a polarized plug (one blade wider than the other). To reduce risk of electric shock, this plug is intended to t into a polarized outlet only one way. If the plug does not t fully into the outlet, reverse the plug. If it still does not t, contact a quali ed electrician. Do not attempt to modify the plug in any way. 15. Make sure machine is turned o before unplugging. 16. A short power-supply cord is provided to reduce risks of becoming entangled in or tripping over a longer cord. Longer detachable power-supply cords or extension cords are available and may be used if care is exercised in their use. If using the machine with an extension cord, make sure the cord is the proper electrical rating for the machine. The extension cord should be arranged so that it does not drape over countertop or tabletop where it can be pulled on by children or tripped over unintentionally. 17. Before serving make sure formula mixture is at safe temperature for baby. 18. Avoid contact with moving parts. Never remove powder container, powder container lid, funnel or water tank while machine is in operation. 19. Do not disassemble. Warning: For infants less than 6 months old, always use bottled water suitable for infant formula preparation. Tap water and/or unsterilized baby bottles can potentially lead to adverse effects for the health of your baby. Only prepare one bottle at a time, feed immediately and follow all instructions carefully. Do not keep leftover formula mix. Always hold baby while feeding. Leaving baby unattended may cause choking. TECHNICAL DATA Supply voltage: 120V ~ 60Hz Model: FRP0045 Current: 2.5A Heater Power: 250W Motor Power: 20W Save these instructions 1 Components Silicone Scraper wash before rst use Water Tank Lid wash before rst use Water Tank wash before rst use Powder Container Parts wash all before rst use Powder Container Lid Stirring Wheel Locking Cover Measuring Wheel Measuring Inserts 1,3,4,5 Powder Container Funnel Cover wash before rst use Funnel wash before rst use Bottle Grate Drip Tray Control Panel Base Power Cord Funnel Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Controls & Indicator Lights Water ounce indicator LEDs No Water warning LED Water temperature indicator LEDs Water ounce selector button Funnel Out Warning LED Stop Button Start Button 2 Set up - Before First Use Wash: Funnel, Funnel Cover, Inside of Water Tank, and all Powder Container parts. (see page 2). Do not put the Powder Container or any of the Powder Container parts in the dishwasher. After washing, make sure all Powder Container parts are COMPLETELY DRY before assembly. Assemble: 1 Select measuring insert by powder type See next page for details Inserts are numbered 1, 3, 4 and 5. Do not use the Measuring Wheel without an insert. Press selected insert into bottom of Measuring Wheel. 2 Place Powder Container on top of Base and Insert Measuring Wheel. 3 Insert Locking Cover and turn to lock under tabs in Powder Container. Make sure Silicone Scraper is installed correctly and does not protrude through the hole in the powder container after assembly. See separate Silicone Scraper instructions for more details. 4 Top View Front After steps 2 & 3 Turn the Measuring Wheel to the position shown at left, with the small arrows on the Measuring Wheel & Powder Container aligned. 5 Insert Stirring Wheel. don't add powder. 6 Place Lid as shown below. turn to lock. make sure tab on lid is on the back corner of machine. Rinse 1 Fill Water Tank to MAX internal parts: line with room temp. Purified Water. With Powder Container assembled follow these steps to rinse internal parts. don't add powder. 2 3 Choose 10 oz. size by pressing ounce button 4 times. Plug in machine and turn power switch to on position. 4 Place 10 ounce or larger container to catch water. Press start to begin rinsing. The machine will stop after dispensing 10oz of water. Dispose of the water captured in the container. The Formula pro is now ready to use. Follow the instructions on pages 5 & 6 for bottle preparation. 3 Measuring Insert Selection Find your formula type below and place indicated insert in measuring wheel. Formula Brand/Type Similac® Advance® Advance® Organic Alimentum® Go & Grow® Go & Grow® Soy NeoSure® Soy Sensitive® for fussiness & gas Sensitive® for Spit-up Supplementation Total ComfortTM PM 60/40 Low Iron Abbott Elecare® Gerber® Good Start® Gentle Good Start® Nourish Good Start® Protect Good Start® Soy Good Start® Soothe Graduates® Gentle Graduates® Protect Graduates® Soy EnfamilTM A.R.® EnfaCare® Gentlease® NutrimigenTM Premium Infant Premium Newborn Prosobee® Enfagrow® Gentlease® Enfagrow® Premium Enfagrow® Soy Insert # 4 4 4 4 5 3 5 4 4 4 4 4 4 5 3 5 5 3 5 5 4 4 3 5 1 5 5 3 3 4 4 Formula Brand/Type Earth's Best Organic® Infant Sensitivity® Soy Baby's Only Organic® Dairy Dairy DHA & ARA Soy LactoRelief TM Store Brand Formula Insert # *3 *4 *3 4 4 4 4 For the following store brands, use the insert indicated for the type of formula in the chart below. America's ChoiceTM, BabiesRUs®, Baby basics®, Bear Essentials, Berkley & Jensen® Baby, ComfortsTM, CVS®, Giant®, Giant Eagle Baby, H-E-B BabyTM, Home 360º TM Baby, Kuddles®, Little OnesTM, MeijerTM, Mom to MomTM, Mother's Choice, Parent's ChoiceTM, Rite Aid®, Simply RightTM, Top Care®, Up & Up®, Wegmans, Walgreens Well BeginningsTM Formula Type Advantage Added Rice Gentle Newborn Organic Premium Sensitivity Soy Tender Toddler & Older infant Kirkland SignatureTM - infant Insert # 5 3 5 5 3 5 4 1 4 4 5 If you do not see your formula brand or type on this list, check www.babybrezza.com for updates or contact customer service at 1-888-396-6552 for assistance. Occasional clumping may occur due to the nature and composition of powdered formula. Always check for clumps and shake or stir the bottle if necessary. 4 Bottle Preparation Before preparing a bottle with the Formula Pro: s!LWAYSUSEACLEANANDSTERILIZEDBOTTLE NIPPLEOROTHERFEEDINGEQUIPMENT s7ASHANDDRYHANDSBEFOREHANDLINGSTERILIZEDBOTTLES s-AKEEACHBOTTLEASNEEDED ANDDONOTSTOREMIXEDFORMULAFORLATERUSE 1 Fill Water Tank to MAX line with room temperature purified water. 2 Fill Powder Container to MAX line with formula powder. PuHr2e0 MAX forbmaulbya Bottle Preparation Continued 3 Select correct height for Drip Tray based on bottle height. Lift up and pull out to remove. Push in and down to install. 4 Tall Bottle Short Bottle Adjust the drip tray so the bottle is as close to the Funnel outlet as possible. This will make sure no formula spills outside of the bottle. 5 Pour powder loosely and evenly into Powder Container. Do not pack powder inside or overfill Powder Container. Powder can be spread evenly with the 3 arms on the Powder Container Lid before closing. About water temperature The heater in the Water Tank will warm the water and keep it warm as long as the machine is powered on. If you refill the Water Tank with cool or room temperature water and need to use the machine right away, the machine can be used while water is heating (flashing yellow light). If you run the machine with cool or room temperature water, before the water is warm and ready, always make sure formula is mixed properly and check for clumps. Temperature Indicator Lights Solid Green = Water warm and ready. Flashing Yellow = Water heating. Flashing Yellow & Green = Water poured into tank is too hot or too cold. &ORQUICKESTWARMINGTIME ALWAYSFILLTHEWATERTANKWITH room temperature or cool water . Flashing green & yellow lights mean the water poured into in the Water Tank is too hot or too cold. The machine will not work while the green & yellow lights flash. If you don't want to wait long for the water to heat, do not fill with water stored in the refrigerator. Never fill Water Tank with hot water. If you boil water before using it in the machine, let the water cool to body or room temperature before pouring it into the Water Tank. 5 Bottle Preparation continued on next page Select bottle size by pressing the ounce button. With each push, the amount will increase 2 ounces. When desired ounce size is selected, press start to dispense formula. 6 Machine will dispense formula into bottle and stop automatically when done. 7 8oz 6oz 4oz 2oz Check level of mixed formula. Level will appear higher due to added powder volume. 8 Check temperature of formula... ...and feed baby. Never remove Water Tank, Funnel or Powder Container while machine is in operation. After baby stops feeding from bottle, discard any leftover formula mixture. Always hold the bottle when feeding baby. Never prop the bottle up and leave your baby to feed unsupervised. 6 Cleaning . . . .U.n.p.lu.g.t.h.e.a.p.pl.ia.n.c.e.b.e.fo.r.e.c.le.a.ni.n.g.. .D.o. n. o. t.u.s.e.a.b.ra.s.iv.e.p.a.d.s.to. .cl.ea. n. .th.e. m. .ac.h.in. e. .. . . . We recommend cleaning The Funnel, Funnel Cover and underside of Powder Container once per day (if machine is used daily). Follow these steps to clean the machine parts. 1 2 3 User Tips Do not remove the Water Tank from the base to refill. Simply lift the Water Tank Lid at the front and pour water in. Make sure to keep water above "MIN" line. Refill Water Tank regularly with room temperature water and keep machine powered on. This way, the water will always be warm and ready to serve. Remove Funnel and Funnel Cover by pulling out and down. 4 Remove Funnel Cover from Funnel by lifting up on Funnel Cover. Wash and rinse Funnel & Funnel Cover thoroughly. Funnel and Funnel Cover are top rack dishwasher safe and are also safe for steam sterilization. With the Funnel removed and Powder Container attached to machine, wipe any dry formula powder from the underside of the Powder Container & Funnel Compartment in a circular motion with a DRY paper towel or DRY soft cloth. Never use a wet or damp cloth to clean the Funnel Compartment or underside of Powder Container. Always make sure the Funnel and Funnel Cover Wipe underside of powder are completely DRY before placing in machine. . . . .co. n.t.ai.n.e.r .w.it.h.c.le.a.n.,.d.ry. c. l.o.th... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . s The inside of the Water Tank should be cleaned once a month with mild detergent and soft cloth or sponge. Rinse inside of Water Tank thoroughly before refilling with clean, purified water. Wipe the outside of the Water Tank with a damp clean cloth. Never immerse Water Tank or get the electronics in the base of the Water Tank wet. If the electronics in the base of the Water Tank get wet, allow to air dry thoroughly before placing back on base. Never place Water Tank in dishwasher. s4HE0OWDER#ONTAINERAND0OWDER#ONTAINER0ARTSSHOULDBECLEANEDONCEAMONTH by emptying any remaining powder (powder can be saved for refill) and cleaned with mild detergent and soft cloth or sponge. Make sure Powder Container and all Powder Container Parts are completely dry before reassembly and refilling the Powder Container with powder. Never place Powder Container in dishwasher. s4HEMACHINE"ASESHOULDBEWIPEDWITHADAMP SOFTCLOTHORSPONGEANDDRIEDIMMEDIATELY .EVERSUBMERGETHEBASEORPLUGINWATEROROTHERLIQUIDS$RYMACHINE"ASEAFTERCLEANING 7 ALWAYS FOLLOW INSTRUCTIONS AND NOTE EXPIRY DATE ON POWDER MANUFACTURER LABEL Always make sure powder level is above the top of the Stirring Wheel. You will know it's time to refill the Powder Container when any of the four horizontal arms of the Stirring Wheel are visible through the powder. Do not use the machine when the powder level is below the MIN line marked on the Powder Container. Refill when arms of stirring wheel are visible When setting up the Powder Container Parts, always make sure the Measuring Wheel and Locking Cover are set up with the arrows aligned as shown in the illustration at right. If the Measuring Wheel rotates when installing the Locking Cover, rotate the Measuring Wheel to the position shown at right. Top View If the powder forms a cone shape mound when refilling the Powder Container, use the 3 arms on the bottom of the Powder Container Lid to gently level the powder. Adjust the Drip Tray so the bottle is as close to the funnel outlet as possible. This will make sure no formula spills on the outside of the bottle. The Formula Pro can be used at any time during the water heating cycle, but not all powders mix well with cool or room temperature water. Always check for clumps & shake or stir the closed bottle gently to mix the powder completely with the water. 8 Troubleshooting Condition Machine will not start. Possible Cause Unit is unplugged. Unit is not turned on. Funnel is removed or not fully inserted. Water Tank is removed or not fully seated. Water level is below "MIN" line. Powder container is removed or not fully seated. Powder container lid is not completely closed. Remedy Make sure the plug is securely inserted into the power outlet. Turn switch on lower back of unit from off to on. Insert funnel or push front of funnel until flush with machine. Place water tank on base or push down all the way. Add more water to water tank. Place powder container on base or push down all the way. Turn Powder container lid clockwise to close completely. Temperature of dispensed formula is too cold. Powder container lid is on backwards. Water in Water Tank is too cold. ( Green & Yellow Temp LEDs Flashing) Make sure tab on outer edge of Powder Container Lid is facing the back of the machine and engaged with safety switch. See page 3, step 6 for diagram. Allow water to warm up or pour warmer water in Water Tank to raise temperature faster. Water in Water Tank is too hot. ( Green & Yellow Temp LEDs Flashing) Allow water to cool down or pour cool water in Water Tank to lower temperature faster. Water has not been heated to correct temperature. Wait for heater to warm water in tank. Green LED in "temp" section of control panel will illuminate when water reaches correct temperature. Not enough powder dispensed. 9 Powder level in powder container is too low. Powder is stuck in powder measuring wheel. Incorrect insert for powder type. Refill Powder Container with more powder. Make sure silicone scraper is installed correctly. Make sure to use the correct insert for powder type. See page 4. Troubleshooting Condition Possible Cause Remedy Too much Incorrect insert for powder powder dispensed. type. Make sure to use the correct insert for powder type. See page 4. Scaling on water tank heater plate. Mineral rich water used persistently. Clean heater plate and use purified/distilled water. Powder build-up on funnel cover and underside of powder container. Frequent use in high humidity. Clean funnel cover and powder container bottom frequently and use machine away from humid areas. Water Tank is full, red no water light is on. Water Tank not fully seated. Push Water Tank down all the way on Base. Funnel will not fit Funnel Cover is not straight all the way in Funnel on funnel or not pushed down Compartment. completely. Align tab on front of Funnel Cover with notch in Funnel and push down Funnel Cover completely. If you can not remedy problems with the machine by using the troubleshooting chart above, please contact Customer Service at 1-888-396-6552. Any other servicing should be performed by an authorized service representative. Customer Service and Warranty If you are experiencing problems with your Baby Brezza Formula Pro, please call our Customer Service department at 1-888-396-6552 before returning the product so that we can offer you our best service customized to your particular situation. Limited 1-Year Warranty The limited warranty is valid only on products bought through authorized resellers and used in the United States and Canada. Buying through an unauthorized reseller or using this product outside of the United States and Canada automatically voids this warranty. This warranty is available to consumers only. You are a consumer if you own a Baby Brezza Formula pro that was purchased at retail for personal, family or household use. Except as otherwise required under applicable state law, this warranty is not available to retailers or other commercial purchasers or owners. We warrant that your Baby Brezza Formula Pro will be free of defects in material or workmanship under normal home use for one year from the date of original purchase. Customer will be required to present original proof of purchase in order to obtain the warranty benefits. In the event that you do not have proof of purchase date, the purchase date for purposes of this warranty will be the date of manufacture. If your Baby Brezza Formula Pro should prove to be defective within the warranty period, we will repair it or, if we consider it necessary, replace it. To obtain warranty services, please call Customer Service at 1-888-396-6552 or write to: Baby Brezza, 250 Passaic Street, Newark, NJ 07104 Attn: Customer Service. 10Mac OS X 10.8.5 Quartz PDFContext