Garmin Official Site
Installation Guide for GARMIN models including: MS-NRX300, MS-NRX300 Black Marine Wired Remote, Black Marine Wired Remote, Marine Wired Remote, Wired Remote, Remote
Nautasea Boatworks
Fusion MS-NRX300 Remote Control - NMEA 2000 Wired, 010-01628-02
File Info : application/pdf, 10 Pages, 1.19MB
DocumentDocumentMS-NRX300 INSTALLATION INSTRUCTIONS Important Safety Information WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. Failure to install this device according to these instructions could result in personal injury, damage to the vessel or device, or poor product performance. CAUTION To avoid possible personal injury, always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. NOTICE When drilling or cutting, always check what is on the opposite side of the surface to avoid damaging the vessel. Getting the Owner's Manuals To fully understand the features and operations of your stereo, you can get the latest stereo owner's manual and translations of manuals from the web. You can also download the full remote owner's manual for more information about using this remote. 1 Go to garmin.com/marine. 2 Select a manual. What's In the Box · Mounting gasket · Four 8-gauge, self-tapping screws · Two screw covers · 6 m (20 ft.) NMEA 2000® backbone cable · NMEA 2000 T-connector · Dust cover February 2024 GUID-56FDBE7F-D572-4ADD-87A0-7729C3FC4E84 v5 Tools Needed · Phillips screwdriver · Drill · 2.5 mm (3/32 in.) drill bit · 50 mm (2 in.) hole saw · Marine sealant (optional) Connection Considerations You can connect the MS-NRX300 remote control to a Fusion® stereo using one of two methods, depending on the stereo: · A new Fusion remote control network · An existing NMEA 2000 network The main difference between a Fusion remote control network and a NMEA 2000 network is how they receive power. A NMEA 2000 network receives power through a power cable connected to the backbone and a power source. A Fusion remote control network receives power from the stereo. The stereo can supply power to a Fusion remote control network if it has the NRX POWER option in the SETTINGS menu or if a red drop cable is included in the stereo box. The Fusion remote control network can support up to three remote controls. If the stereo cannot supply power to the Fusion remote control network, you must connect the MS-NRX300 remote control using the NMEA 2000 network. NMEA 2000 Connection Considerations You may connect the remote control to the stereo using an existing NMEA 2000 network. · You can connect more than three MS-NRX300 remote controls to one Fusion stereo. · You are connecting to a Fusion stereo that cannot provide power to the remote. · You can control a connected Fusion stereo from a FUSION-LinkTM compatible chartplotter. 2 Item Description Fusion stereo Compatible chartplotter MS-NRX300 remote control* 12 Vdc power source with an ignition or in-line switch NMEA 2000 drop cable and T-connector, dependant on stereo. See the following table. NMEA 2000 drop cable NMEA 2000 power cable, 2 m (6 ft.) NMEA 2000 terminator or backbone cable NMEA 2000 T-connector* *Components included with the MS-NRX300 remote control. NOTE: The NMEA 2000 network may include other NMEA 2000 devices. NMEA 2000 Cables and Software Settings The cables required to connect to the NMEA 2000 network vary depending on the stereo. See the table below to determine which cables and possible software settings are required for your stereo model. All stereos require a T-connector to connect the drop cable to the NMEA 2000 network. You can extend the drop cable to a maximum length of 6 m (20 ft.) using a standard NMEA 2000 cable. 3 Stereo NRX POWER option in software. Examples: · ApolloTM MS-RA770 · Apollo MS-RA670 Cables and software settings required · Included NMEA 2000 drop cable required. · Included NMEA 2000 T-connector required. NOTICE To avoid damaging other devices on the NMEA 2000 network, the NRX POWER option must be off. This is off by default. See the stereo owner's manual for more information. NRX POWER option in software, NMEA 2000 cable hardwired to stereo. · Use the cable on the stereo wiring harness. · Included NMEA 2000 T-connector required. NOTICE To avoid damaging other devices on the NMEA 2000 network, the NRX POWER option must be off. This is off by default. See the stereo owner's manual for more information. No NRX POWER option in software. · Included NMEA 2000 drop cable required. · Included NMEA 2000 T-connector required. No NRX POWER option in software, red cable included. · Drop cable required. · Included NMEA 2000 T-connector required. NOTICE To avoid damaging other devices on the NMEA 2000 network, do not use the red drop cable included with the stereo to connect to the NMEA 2000 network. 4 Fusion Remote Control Network Connection Considerations You may connect the remote control to the stereo using a standalone powered Fusion remote control network if you have the following conditions. · You do not have a full NMEA 2000 network on your boat. · You are connecting three or fewer MS-NRX300 remote controls to one Fusion stereo. · You are connecting to a Fusion stereo that can provide power to the remote. The stereo can supply power to the remote control if it has an NRX POWER option in the SETTINGS menu or if a red drop cable is included. Item Description Fusion stereo MS-NRX300 remote control* NMEA 2000 drop cable. See the following table. NMEA 2000 female terminator* NMEA 2000 T-connector* NMEA 2000 backbone cable, 6 m (20 ft.)* NMEA 2000 inline terminator* *Components included with the MS-NRX300 remote control. 5 Fusion Remote Control Network Cables and Software Settings The cables required to connect to the Fusion remote control network vary depending on the stereo. See the table below to determine which cables and possible software settings are required for your stereo model. The stereo can supply power to the remote control if it has an NRX POWER option in the SETTINGS menu or if a red drop cable is included. Stereo characteristics Cables and software settings required · Included NMEA 2000 drop cable required. NRX POWER option in software. · You must enable the NRX POWER setting to provide power to the remote control. Select > SETTINGS > POWER OPTIONS > NRX POWER. NRX POWER option in software, NMEA 2000 cable hardwired to stereo. · Use the cable on the stereo wiring harness. No additional cables needed. · You must enable the NRX POWER setting to provide power to the remote control. Select > SETTINGS > NRX POWER. No NRX POWER option in software. Not supported. Connect to a NMEA 2000 network. Mounting Considerations When selecting a mounting location, observe these considerations. · The device must be mounted in a location where there is at least 75 mm (3 in.) of clearance behind the mounting surface and you can access the controls after it is mounted. · If you want to mount the device outside the boat, it must be mounted in a location well above the waterline, where it is not submerged. · If you want to mount the device outside the boat, it should be mounted in a location where it will not be damaged by a docks, pilings, or other pieces of equipment. Mounting the Remote Control 1 At the mounting location, use a 50 mm (2 in.) hole saw to cut through the mounting surface. 2 Place the remote control in the cutout and mark the pilot holes. 3 Remove the remote control from the cutout, and using a 2.5 mm (3/32 in.) drill bit, drill the pilot holes. 4 Apply marine sealant around the cutout (optional). 5 Place the gasket on the back of the remote control. 6 Feed the attached NMEA 2000 cable through the cutout. 7 Place the remote control in the cutout. 8 Secure the remote control to the mounting surface using the included screws. 9 Install the decorative bezel around the edges of the remote control. 10 Route the NMEA 2000 cable away from sources of interference and connect it to the NMEA 2000 network or the Fusion remote control network. 6 More Information Specifications Specification Operating voltage Electrical input current NMEA 2000 Load Equivalency Number (LEN) Operating temperature Storage temperature Water rating Top Dimensions Measurement From 10.8 to 16 Vdc negative ground 110 mA at 12 Vdc 3 (150 mA) From 0 to 50°C (from 32 to 122°F) From -20 to 70°C (from -4 to 158°F) IEC 60529 IPX7 Item Measurement 110 mm (45/16 in.) 42 mm (15/8 in.) 28 mm (13/32 in.) 16.5 mm (41/64 in.) 7 Front Dimensions 110 mm (4.33 in.) 70 mm (2.76 in.) Supported NMEA 2000 PGN Information NOTE: You must connect the device to a NMEA 2000 network for NMEA 2000 support. 8 PGN Number 127250 128259 128267 129025 129026 129029 129284 130306 130310 130311 130312 130314 130577 Data Field Heading sensor reference: · 0: True · 1: Magnetic Water speed reference: · 00: Paddle wheel · 01: Pitot tube · 02: Doppler log · 03: Correlation log (ultrasound) · 04: Electromagnetic (EM) log Water depth: · Offset add or subtract Position: · Latitude and longitude Course Over Ground (COG) and Speed Over Ground (SOG) COG reference: · 0: True · 1: Magnetic Global Navigation Satellite System (GNSS) position data Navigation data: · ETA date Wind data reference: · 0x02 : Apparent wind (relative to the vessel centerline) Water temperature and air pressure Water temperature and air pressure Temperature and temperature source: · 00 : Sea temperature Actual pressure and pressure source: · 00 : Atmospheric pressure Direction data and COG reference: · 0: True · 1: Magnetic Registering Your MS-NRX300 Help us better support you by registering the product online. · Go to garmin.com. · Keep the sales receipt, or a copy, in a safe place. 9 Software Updates You must update the software for this device using a connected compatible stereo or using the Fusion-LinkTM app. To make sure the device functions correctly with all compatible stereos on the network, you should update the software in all devices after you install this device. For software update instructions, see the online owner's manual for this device or for a connected compatible stereo. / SJ/T11364 : (GB/T26572) : , (GB/T26572) * © 2016 Garmin Ltd. or its subsidiaries Garmin®, the Garmin logo, Fusion®, and the Fusion logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. FUSION-LinkTM is a trademark of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. NMEA®, NMEA 2000®, and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association. All rights reserved. Other trademarks and trade names are those of their respective owners. © 2016 Garmin Ltd. or its subsidiaries support.garmin.com