User Manual for Shinex Electronic Industries models including: CTL1128A, 2AXW8-CTL1128A, 2AXW8CTL1128A, DCPC03 Device, DCPC03 Device
Shinex Electronic Industries Inc. CTL1128A SHINEX ACDK 2AXW8-CTL1128A 2AXW8CTL1128A ctl1128a
User's Manual Product Name: __ SHINEX ACDK ______ Model Name: DCPC03 Please refer the following information for setting up. Product Spec.: __ACDK_____ Control, Operation, Settings 1) Login settings 2) Individual control 3) Collective starting/stopping and settings for control group 4) Schedule control 5) Interlocking control 6) Emergency stop control for fires 7) Power failure and recovery processing control 8) Centralized control of air conditioners Type C D D G D D G 1 1N22N USB 1 USB 2 Micro SD Parameter USB2 USB1 Micro SD LAN RS485 Type C Description USB_ACDK USB_ACDK Micro SD Solt Network RS485 D1+D1-D2+D2Power In 5V3A CPU Memory Storage Input Power Range M/B Form Factor Other Components Display Interface Interface Other Other Jumper OS Support Temperature Weight Size Dual-Core RAM System Emmc Type C Battery Panel LVDS Backlight LAN USB 2.0 RS485 I2C SD Card M.2 2230 Test port USB OTG Thermal sensor Auto power on Dip switch OS Support Store Operating Host bady i.MX6 DualLITE,1GHz,MCIMX6U5DVM10AC,NXP Single Channel DDR3L,up to 1GB 16GB eMMC 5VDC power input, +-5% tolerance Use USB type C as power connector on rear I/O PCB dimension 168 x 82mm CR2032 coin cell,by on board socket Screen Size 10.1 inches (diagonal) Display Format 1024(H) x (R,G,B) x 600(V) dots Back-light LED LCD Active Area 222.72(H) × 125.28(V) mm 1 x LVDS: resolution up to 1024*600@60Hz LVDS header follows panel spec Panel Power default 3.3V,5V can be optional 1 Pin wafer for backlight with 5V, 1A current. Signal includes PWM brightness control,power on/off signal 1 GbE speed LAN on rear I/O,by AR8033 Ethernet transceiver. CPU has Iimitation note on full speed throughput 2 x USB 2.0 Type A on rear I/O 2 x RS485 on rear I/O 6 pin terminal block connector One I2C header for touch control 1 x Micro SD card on rear I/O M.2 socket E key,support type 2230 With Wi-Fi M.2 2230 Moudule Card RTL8822CE(ENLI) on M.2 socket Debug UART USB2 OTG,micro USB,for service purpose One thermal sensor Auto power on Dip switch for system setting Support Linux NXP i.MX6 Yocto 2.5 0 to 60 °C 0 to 40 °C 1098.65g ± 50g (W)272.2 ± 0.7mm (D)181.6 ± 0.7mm (H)36.1 ± 0.7mm Federal Communication Commission Interference Statement Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note, Supplier's Declaration of Conformity §2.1077(a)(3) Name: __SHINEX ACDK _______ Address: @USA Telephone number or Internet contactIrene Hou (侯姿名) Adobe PDF Library 15.0