Hikvision Gigabit Unmanaged PoE Switch

Packing List

Interfaces

Front Panel

DS-3E0505HP

Features: PWR Indicator, PoE-MAX Indicator, Hi-PoE Port, Gigabit PoE Ports, Gigabit RJ45 Port.

DS-3E0510HP

Features: PoE-MAX Indicator, Gigabit Hi-PoE Port, Gigabit PoE Ports, UPLINK, Gigabit RJ45 Ports, Gigabit SFP Fiber Optical Port (Port 10), LINK/ACT Indicator (Port 10), PWR Indicator.

DS-3E0520HP

Features: LINK/ACT PoE Indicator, PoE Indicator, DIP Switch, Gigabit Hi-PoE Ports, Gigabit PoE Ports, Gigabit RJ45 Ports, Gigabit SFP Fiber Optical Ports (Port 19/10), PoE-MAX Indicator, PWR Indicator.

Note: The front panel of DS-3E0528HP switch is similar to DS-3E0520HP, with differences in the number of ports and indicators.

Port Descriptions:

• Gigabit Hi-PoE Port: Used for Hi-PoE PTZ cameras connection, max power is 90 W.
• Gigabit PoE Port: Used for other PoE devices connection via network cables.
• Gigabit RJ45 Port: Used for devices connection via network cables.
• Gigabit SFP Fiber Optical Port: Used for devices connection via optical fiber when plugged into an optical module.

DIP Switch Modes:

• Extend: The last 2 PoE ports of DS-3E0505/10HP and the last 4 of DS-3E0520/28HP support network transmission up to 300 meters.
• Isolation: Data transmission of each port is isolated to improve network security.
• PoE Watchdog: Auto-detects and restarts unresponsive cameras.

Device Connection

Connect your devices according to your networking requirements. The diagram illustrates a typical connection for the DS-3E0510HP series switch.

Connection Types:

• Data (Blue line)
• Power+Data (PoE) (Purple line)
• Optical Fiber (Grey line with arrows)

Example Scenario: A switch connected to an NVR, a Control Center via the Internet, an 802.3bt Hi-PoE PTZ camera, a Wireless AP, and a PoE VoIP Phone. The connection supports up to 300 meters for Hi-PoE devices and features 6 KV Surge Protection.

Note: DS-3E0505HP series switches do not have fiber optical ports.

Device Installation

Prerequisites:

• Ensure the rack or desktop is stable and firm.
• The room must be well-ventilated with at least 10 cm clearance on all sides for cooling.
• Maintain at least 1.5 cm vertical distance between switches when installing in a rack.

DS-3E0505/10HP Installation:

These switches support desktop and wall-mounted installation. For wall mounting, follow the provided illustration.

DS-3E0520/28HP Installation:

These switches support rack installation only.

1. Check the grounding and stability of the rack.
2. Attach the two L-shaped brackets to the sides of the switch using the provided screws.
3. Place the switch in the rack and secure it with self-prepared screws, ensuring stable installation.

Grounding

Purpose: Grounding protects the switch from overvoltage and overcurrent induced by lightning and ensures personal safety.

Methods:

• With Grounding Bar: Connect the grounding cable to the grounding terminal and the grounding bar.
• Without Grounding Bar: Connect the grounding cable to the grounding terminal and an angle steel buried at least 0.5m deep.

Port Connection

PoE Port Connection:

Connect the switch to the PoE ports of opposite end devices such as network cameras, IP cameras, NVRs, or other switches. The switch supports auto MDI/MDIX, allowing the use of straight-through or crossover cables.

Fiber Optical Port Connection:

• Avoid bending fiber optic cables with a curvature radius less than 10 cm.
• Do not look directly at the fiber optic connector, as the laser can be harmful to eyes.

1. Connect the two paired SFP optical modules with an optical fiber.
2. Smoothly plug the SFP optical module into the switch's SFP port slot until it is securely attached.
3. After powering on the switch, check the Link/Act indicator. A lit indicator signifies a connected link; an unlit indicator means the link is disconnected. Verify the cable connection and ensure the opposite device is powered on.

Power-On Checking

Before powering on your switch, ensure:

• The operating power supply complies with the rated input standard.
• Port cables and grounding cables are correctly connected.
• If outdoor cabling is used, a lightning rod and lightning arrester are connected to the cable.

Use the attached power cord to power up the switch.

Indicator Status:

Regulatory Information

FCC Information:

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

EU Conformity Statement:

This product and its accessories are marked with "CE" and comply with applicable harmonized European standards under the EMC Directive 2014/30/EU, LVD Directive 2014/35/EU, and RoHS Directive 2011/65/EU.

WEEE Directive (2012/19/EU): Products marked with this symbol should not be disposed of as unsorted municipal waste. Return to your local supplier or designated collection points for recycling.

Battery Directive (2006/66/EC): Contains batteries that cannot be disposed of as unsorted municipal waste. Refer to product documentation for battery information. Batteries may be marked with symbols indicating Cadmium (Cd), Lead (Pb), or Mercury (Hg).

Industry Canada ICES-003 Compliance:

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.