Whyte Technologies – Digital innovation made easy
Instruction Manual for Whyte models including: WSCR504, WSCR506, WSCR508, WSCR512, WSCR516, 4 Way dSCR Multiswitch
PRODUCT DESCRIPTION 1. Inputs Satellite 2. Input Terrestrial 3. Corner Mounting Brackets 4. LNB Selector Switch 5. Subscriber (REC) Outputs 6. Subscriber Output Status Indicator
File Info : application/pdf, 16 Pages, 1.52MB
DocumentDocumentdSCR Multiswitch INSTRUCTION MANUAL WSCR504 | WSCR506 | WSCR508 WSCR512 | WSCR516 www.whytetechnologies.com In the interest of continuous improvement, all specifications of products within this brochure are subject to change without notice. CONTENTS Safety 3 Precautions 3 Guarantee 3 General Description 4 Product Description 5 Technical Description 6 Installation Instructions 8 Commissioning the Multiswitch 11 Example Configuration 12 Specifications 14 2 SAFETY The Multiswitches are intended for indoor use only. Do not install the Multiswitch in damp, humid, hot or dusty areas. Switch off and remove the power supply when making connections to the Multiswitch to avoid damaging the unit. Always earth bond the Multiswitch using the Earth Bonding Lug and/or the Earth Terminal Bars to a suitable earth bonding point using minimum 4mm² diameter earth cable. PRECAUTIONS To ensure trouble free operation: Do not remove the cover of the Multiswitch or disassemble it as this will invalidate the guarantee. The female F connectors on this unit were designed for use with '100' type coaxial cable with a centre core diameter of 1mm². When using larger CT125 or CT167 cables, you must ensure that suitable F connectors with reducing pins are used otherwise damage to the unit will occur which will invalidate the guarantee. Do not over tighten the F connectors (finger tight only). GUARANTEE All Whyte products are guaranteed for a period of 4 years from the date of purchase against defects. Within this guarantee period, Whyte Technologies will repair or replace the faulty product. In the unlikely event, please return any faulty products to your dealer. The Guarantee will be deemed as void if the serial number on the product is removed, damaged or illegible. The Guarantee excludes defects caused by incorrect use, accidental damage, disassembly, water/fire/lightning damage or lack of ventilation. 3 GENERAL DESCRIPTION Whyte Series D is a range of advanced Cascadable Hybrid dSCR Multiswitches. Seamless integration with conventional IRS Systems due to extremely low power consumption, low loss passive trunks and high gain TERR, make the new Series D range from Whyte the most versatile and easy to install dSCR Multiswitch range available. The Series D range can be directly conjoined with Series 5 conventional Multiswitches using the supplied F type couplers to seamlessly create Hybrid IRS Systems. Use Series 5 Launch Amplifiers, Taps, Splitters and Power Supply Units to create large scale dSCR only or Hybrid IRS Systems. Each Subscriber Output provides Satellite (SkyQ, dSCR & Legacy), TV and Radio. Satellite subscriber signal levels in both Legacy and dSCR mode are automatically set to 89dBV (self-commissioning/AGC). dSCR and Legacy mode is automatically detected and switched over on a per-subscriber port basis. Terrestrial signal levels are controlled via a manual Gain Control knob and a selectable Protean Tap which permits a wide range of TERR input signal levels ranging from 50 to 108dBV. The reception of 2 satellites can easily be achieved by utilising 2 Wideband LNB's and switching the unit to Wideband LNB mode. The unit can be powered directly via the DC input port or be remotely powered via the trunk lines. 4 PRODUCT DESCRIPTION 3 4 1 2 1 12 3 14 5 11 5 10 REC 1 VL HL V Sat A H WB LNB Q TERR VH HH Q V Sat B H WB ON DC 12V OFF WSCR508 8 Way dSCR Multiswitch REC 2 TERR Gain REC 3 REC 4 REC 5 SAT dSCR / Legacy Frequency 290 ~ 2340MHz Min/Max Input 64 ~ 104dBV Output (AGC) 89dBV Gain (AGC) -5dB ~ +25dB REC 7 Trunk Loss Max - 5dB Consumption Min / Max @ 18V Compatibility LED Status DC IN 18V VL HL TM TERR 0 dB -10dB REC 6 -20dB Terrestrial Frequency 87 ~ 790MHz Min/Max Input 52 ~ 102dBV Max Output 90dBV Gain 8dB ±2dB Trunk Loss Max - 5dB 0.1A / 0.15A Sky UK- EN50607 - EN50494 SCR Mode Legacy Mode Flashing Green Solid Green REC 8 TERR VH HH 14 5 6 5 13 3 12 7 8 7 3 1. Inputs Satellite 2. Input Terrestrial 3. Corner Mounting Brackets 4. LNB Selector Switch 5. Subscriber (REC) Outputs 6. Subscriber Output Status Indicator 7. Trunk Output SAT 8. Trunk Output TERR 9. TERR Protean Tap 10. Auxiliary DC Input 11. TERR Gain Control 12. TERR 12V DC Switch 13. Earth Terminal 14. Earth Terminal Bar 5 TECHNICAL DESCRIPTION DC POWERING The Whyte Series D range can be Line Powered via any of the SAT input and output Trunk Lines. All SAT Trunk Lines are DC passing, whilst the TERR Trunk Line is DC isolated. The Multiswitches have an Auxiliary DC Input which will power the Multiswitch as well as provide power to the SAT input and output Trunk Lines when fitted with a Whyte PSU. A 12V DC switch is available to power a Mast Head Amplifier connected to the TERR input. If a Mast Amplifier is not being used this must be left in the OFF position. SUBSCRIBER PORT MODE INDICATION Each Subscriber Port has an LED indicator to confirm the mode status. Legacy Mode: Solid Green dSCR Mode: Blinking Green Legacy Mode: This is the default mode of the Multiswitch. In this mode the Multiswitch functions like a conventional legacy Multiswitch. dSCR Mode: When a dSCR Set Top Box is connected, the corresponding port will acknowledge the dSCR DiSEqC commands and switch to dSCR mode. To revert back to legacy mode the power to the Subscriber Port needs to be interrupted momentarily. A reboot of the Multiswitch is NOT necessary to revert back to legacy mode. 6 STANDALONE MODE Series D Multiswitches can be used in stand alone mode when powered directly via the 18V Auxiliary Input by using a Whyte Power Supply Unit (sold separately). Any unused (open) SAT/TERR Trunk Outputs must be terminated using 75 DC Blocked F-Type Terminators. CASCADE MODE Multiple Whyte Series D Multiswitches can be connected in cascade using the supplied F Type Couplers. In Cascade Mode, the PSU can be connected to any Series D Multiswitch, Splitter, Tap or Amplifier within the system for ease of installation. Hence, all Series D Multiswitches will be remotely powered via the SAT Trunk Lines. Care must be taken to select the appropriate type and number of PSU's required depending on the current requirements of the system as a whole. Remember to calculate the total current consumption of all Multiswitches, Amplifiers and LNB's within the system. Always terminate the SAT/TERR Trunk Outputs of the last Multiswitch in a cascade using 75 DC Blocked F-Type Terminators. QUATTRO/WIDEBAND LNB SWITCH The Series D range is compatible with both Quattro and Wideband LNB's. To enable compatibility with a Quattro LNB (5 Wire Trunk) place the switch in the position marked "Q". To enable compatibility with a Wideband LNB (3 Wire Trunk) place the switch in the position marked "WB". Note: when using wideband mode ensure that any amplifiers, taps or splitters that form part of a system are wideband compatible. 2 SAT RECEPTION The reception of two satellites can be achieved via a 5 wire trunk by utilising 2 Wideband LNB's. The required satellite can then be selected by the STB using simple diseqc Satellite A and B commands. 7 INSTALLATION INSTRUCTIONS MOUNTING THE MULTISWITCH Select a suitable location to install the Multiswitch. Do not install the Multiswitch in damp, humid, hot or dusty areas. Using the screw slots on the Corner Brackets, secure the Multiswitch using the appropriate fixing screws and wall plugs to suit the relevant wall surface or cabinet. CONNECTING THE SAT & TERR INPUT AND OUTPUT TRUNK CABLES Use a suitably sized Satellite Dish to provide adequate signal levels from the satellite being received. Ensure that the Satellite Drop Cables are connected correctly to the LNB's. Ensure that the F Connectors are properly sealed against water ingress. If a Composite Cable (multi core coaxial cable) has been used, ensure that the outer jacket is not facing upwards and cannot collect rain water. Check the Terrestrial Drop Cable and ensure that this has also been sealed against water ingress. If a Triplexer has been used to combine FM and DAB aerials with the UHF Terrestrial Aerial, ensure that this is also water tight. Ensure that all drop cables have drip loops prior to their entering the building. Connect the SAT and TERR drop cables to the corresponding Satellite and TERR Inputs on the Multiswitch. Connect any additional Multiswitches or Trunk Cables to the Satellite & TERR Trunk Outputs as applies. Ensure that you terminate the last Multiswitch in a cascade using 75 DC Blocked F-type Terminators. 8 EARTH BONDING Earth bond the Multiswitch to the Earth Bonding Lug and/or the Earth Terminal Bars using minimum 4mm² Earth Bonding Cable. It is best practise to earth bond across all Multiswitches using a single unbroken Earth Bonding Wire. To achieve this, strip away 3cm of the insulation of a length of 4mm² Earth Bonding Wire. See Figure 1. Unscrew the Earth Bolt on the Earth Terminal Bar to provide enough clearance to wrap the Earth Bonding Wire around the Earth Bolt. See Figure 2. Tighten the Earth Bolt and route the Earth Bonding Wire to all other Earth Terminal Bars and terminate as detailed above. Make sure that the Earth Bonding Cable is connected directly to the building's PME. Figure 1 Figure 2 9 CONNECTING THE SUBSCRIBER CABLES Terminate the Subscriber Cables with good quality F Connectors and connect to the Subscriber Outputs. The F Connectors should be fitted to the coaxial cable correctly, ensuring that the centre core protrudes 3mm above the F Connector body. See figure 3. Ensure that you do not exceed the bending radius of the Coaxial Cable being used. Figure 3 3mm CONNECTING THE POWER SUPPLY UNIT (PSU) Calculate the total current consumption of the Multiswitch(es), LNB and any Launch Amplifiers that make up the complete IRS System. The current consumption of the Series D Multiswitch range can be found in the Specification section of this manual. If in doubt, assume the current consumption of each LNB to be 200mA max (0.2A). Connect a suitable Whyte PSU to the Auxiliary 18V DC Input. If more than one PSU is required, the additional PSU(s) may be connected to any other Multiswitch, Launch Amplifier, Tap or Splitter within the system. When all connections have been made, connect the PSU to a 240V supply to power up the IRS System. It is highly advisable to isolate and hence divide the system in to DC Groups containing only a single PSU per group, by using F-type DC blockers (not supplied). 10 USER BAND FREQUENCIES Sky UK UB FREQ 3 1680 9 1280 11 1380 14 1480 15 980 16 1030 17 1080 18 1130 19 1530 20 1580 21 1630 22 1730 23 1780 24 1830 25 1880 26 1930 EN50607 UB UB 5 985 6 1050 7 1115 8 1275 9 1340 10 1485 11 1550 12 1615 13 1745 14 1810 15 1875 16 1940 EN50494 UB UB 1 1210 2 1420 3 1680 4 2040 COMMISSIONING THE MULTISWITCH See Figure 4: 1. Connect a spectrum analyser to any Subscriber Output of the first Multiswitch 2. Set the TERR Pro-Tap to -20dB 3. Set the Spectrum Analyser to Terrestrial. Using the TERR Gain Control adjust the Terrestrial signal to the required digital channel power level. If the signal cannot reach the required level, set the TERR Pro-Tap to -10dB and readjust the TERR Gain Control. If required, set the Pro-Tap to -0dB and readjust the Gain Control. 4. Check the SAT signal levels in Legacy and dSCR mode. These will not require adjustment as they are self-commissioned using Automatic Gain Control. 5. Repeat the above for all other Multiswitches in the IRS System as applies. 11 EXAMPLE CONFIGURATION Figure 4 12 WPSU-2.5A WATS-517WB 4 X IF + TERR Launch Amp TERR 4G 5G SAT: Freq Range 290~2340MHz | Gain 30dB | Slope 12dB±1dB | Max Output 112dBµV TERR: Freq Range 87~790MHz | Gain 24dB | Slope 8dB±1dB | Max Output 112dBµV Quattro and WB compatible WATS-517WB REC 1 VL HL V Sat A H WB LNB Q TERR VH HH Q V Sat B H WB ON DC 12V OFF WSCR504 4 Way dSCR Multiswitch REC 2 SAT dSCR / Legacy Frequency 290 ~ 2340MHz Min/Max Input 64 ~ 104dBV Output (AGC) 89dBV Gain (AGC) -5dB ~ +25dB REC 3 Trunk Loss Max - 5dB Consumption Min / Max @ 18V Compatibility LED Status DC IN 18V VL HL Terrestrial TERR Gain Frequency Min/Max Input 87 ~ 790MHz 52 ~ 102dBV TM TERR Max Output Gain 101dBV 8dB ±2dB 0 dB -10dB -20dB Trunk Loss Max - 5dB 0.1A / 0.15A Sky UK- EN50607 - EN50494 SCR Mode Flashing Green Legacy Mode Solid Green REC 4 TERR VH HH REC 1 VL HL V Sat A H WB LNB Q TERR VH HH Q V Sat B H WB ON DC 12V OFF WSCR508 8 Way dSCR Multiswitch REC 2 TERR Gain REC 3 REC 4 REC 5 SAT dSCR / Legacy Frequency 290 ~ 2340MHz Min/Max Input 64 ~ 104dBV Output (AGC) 89dBV Gain (AGC) -5dB ~ +25dB REC 7 Trunk Loss Max - 5dB Consumption Min / Max @ 18V Compatibility LED Status DC IN 18V VL HL TM TERR 0 dB -10dB REC 6 -20dB Terrestrial Frequency 87 ~ 790MHz Min/Max Input 52 ~ 102dBV Max Output 90dBV Gain 8dB ±2dB Trunk Loss Max - 5dB 0.1A / 0.15A Sky UK- EN50607 - EN50494 SCR Mode Legacy Mode Flashing Green Solid Green REC 8 TERR VH HH WSCR504 WSCR508 Quick Fit Couplers REC 1 VL HL V Sat A H WB LNB Q TERR VH HH Q V Sat B H WB ON DC 12V OFF WSCR504 4 Way dSCR Multiswitch REC 2 SAT dSCR / Legacy Frequency 290 ~ 2340MHz Min/Max Input 64 ~ 104dBV Output (AGC) 89dBV Gain (AGC) -5dB ~ +25dB REC 3 Trunk Loss Max - 5dB Consumption Min / Max @ 18V Compatibility LED Status DC IN 18V VL HL Terrestrial TERR Gain Frequency Min/Max Input 87 ~ 790MHz 52 ~ 102dBV TM TERR Max Output Gain 101dBV 8dB ±2dB 0 dB -10dB Trunk Loss Max - 5dB 0.1A / 0.15A Sky UK- EN50607 - EN50494 -20dB SCR Mode Flashing Green Legacy Mode Solid Green REC 4 TERR VH HH REC 1 VL HL V Sat A H WB LNB Q TERR VH HH Q V Sat B H WB ON DC 12V OFF WSCR508 8 Way dSCR Multiswitch REC 2 TERR Gain REC 3 REC 4 REC 5 SAT dSCR / Legacy Frequency 290 ~ 2340MHz Min/Max Input 64 ~ 104dBV Output (AGC) 89dBV Gain (AGC) -5dB ~ +25dB REC 7 Trunk Loss Max - 5dB Consumption Min / Max @ 18V Compatibility LED Status DC IN 18V VL HL TM TERR 0 dB -10dB REC 6 -20dB Terrestrial Frequency 87 ~ 790MHz Min/Max Input 52 ~ 102dBV Max Output 90dBV Gain 8dB ±2dB Trunk Loss Max - 5dB 0.1A / 0.15A Sky UK- EN50607 - EN50494 SCR Mode Legacy Mode Flashing Green Solid Green REC 8 TERR VH HH WSCR504 WSCR508 13 REC 1 VL HL V Sat A H WB LNB Q TERR VH HH Q V Sat B H WB ON DC 12V OFF WSCR508 8 Way dSCR Multiswitch REC 2 TERR Gain REC 3 REC 4 REC 5 SAT dSCR / Legacy Frequency 290 ~ 2340MHz Min/Max Input 64 ~ 104dBV Output (AGC) 89dBV Gain (AGC) -5dB ~ +25dB REC 7 Trunk Loss Max - 5dB Consumption Min / Max @ 18V Compatibility LED Status DC IN 18V VL HL TM TERR 0 dB -10dB REC 6 -20dB Terrestrial Frequency 87 ~ 790MHz Min/Max Input 52 ~ 102dBV Max Output 90dBV Gain 8dB ±2dB Trunk Loss Max - 5dB 0.1A / 0.15A Sky UK- EN50607 - EN50494 SCR Mode Legacy Mode Flashing Green Solid Green REC 8 TERR VH HH REC 1 VL HL V Sat A H WB LNB Q TERR VH HH Q V Sat B H WB ON DC 12V OFF WSCR504 4 Way dSCR Multiswitch REC 2 SAT dSCR / Legacy Frequency 290 ~ 2340MHz Min/Max Input 64 ~ 104dBV Output (AGC) 89dBV Gain (AGC) -5dB ~ +25dB REC 3 Trunk Loss Max - 5dB Consumption Min / Max @ 18V Compatibility LED Status DC IN 18V Terrestrial TERR Gain Frequency Min/Max Input 87 ~ 790MHz 52 ~ 102dBV TM TERR Max Output Gain 101dBV 8dB ±2dB 0 dB -10dB -20dB Trunk Loss Max - 5dB 0.1A / 0.15A Sky UK- EN50607 - EN50494 SCR Mode Legacy Mode Flashing Green Solid Green REC 4 VL HL TERR VH HH WM512 WSCR504 WSCR508 WT52-05WB WM512 REC 1 VL HL V Sat A H WB LNB Q TERR VH HH Q V Sat B H WB ON DC 12V OFF WSCR508 8 Way dSCR Multiswitch REC 2 TERR Gain REC 3 REC 4 REC 5 SAT dSCR / Legacy Frequency 290 ~ 2340MHz Min/Max Input 64 ~ 104dBV Output (AGC) 89dBV Gain (AGC) -5dB ~ +25dB REC 7 Trunk Loss Max - 5dB Consumption Min / Max @ 18V Compatibility LED Status DC IN 18V VL HL TM TERR 0 dB -10dB REC 6 -20dB Terrestrial Frequency 87 ~ 790MHz Min/Max Input 52 ~ 102dBV Max Output 90dBV Gain 8dB ±2dB Trunk Loss Max - 5dB 0.1A / 0.15A Sky UK- EN50607 - EN50494 SCR Mode Legacy Mode Flashing Green Solid Green REC 8 TERR VH HH REC 1 VL HL V Sat A H WB LNB Q TERR VH HH Q V Sat B H WB ON DC 12V OFF WSCR504 4 Way dSCR Multiswitch REC 2 SAT dSCR / Legacy Frequency 290 ~ 2340MHz Min/Max Input 64 ~ 104dBV Output (AGC) 89dBV Gain (AGC) -5dB ~ +25dB REC 3 Trunk Loss Max - 5dB Consumption Min / Max @ 18V Compatibility LED Status DC IN 18V Terrestrial TERR Gain Frequency Min/Max Input 87 ~ 790MHz 52 ~ 102dBV TM TERR Max Output Gain 101dBV 8dB ±2dB 0 dB -10dB -20dB Trunk Loss Max - 5dB 0.1A / 0.15A Sky UK- EN50607 - EN50494 SCR Mode Legacy Mode Flashing Green Solid Green REC 4 VL HL TERR VH HH WSCR504 WSCR508 REC 1 VL HL V Sat A H WB LNB Q TERR VH HH Q V Sat B H WB ON DC 12V OFF WSCR508 8 Way dSCR Multiswitch REC 2 TERR Gain REC 3 REC 4 REC 5 SAT dSCR / Legacy Frequency 290 ~ 2340MHz Min/Max Input 64 ~ 104dBV Output (AGC) 89dBV Gain (AGC) -5dB ~ +25dB REC 7 Trunk Loss Max - 5dB Consumption Min / Max @ 18V Compatibility LED Status DC IN 18V VL HL TM TERR 0 dB -10dB REC 6 -20dB Terrestrial Frequency 87 ~ 790MHz Min/Max Input 52 ~ 102dBV Max Output 90dBV Gain 8dB ±2dB Trunk Loss Max - 5dB 0.1A / 0.15A Sky UK- EN50607 - EN50494 SCR Mode Legacy Mode Flashing Green Solid Green REC 8 TERR VH HH REC 1 VL HL V Sat A H WB LNB Q TERR VH HH Q V Sat B H WB ON DC 12V OFF WSCR504 4 Way dSCR Multiswitch REC 2 SAT dSCR / Legacy Frequency 290 ~ 2340MHz Min/Max Input 64 ~ 104dBV Output (AGC) 89dBV Gain (AGC) -5dB ~ +25dB REC 3 Trunk Loss Max - 5dB Consumption Min / Max @ 18V Compatibility LED Status DC IN 18V Terrestrial TERR Gain Frequency Min/Max Input 87 ~ 790MHz 52 ~ 102dBV TM TERR Max Output Gain 101dBV 8dB ±2dB 0 dB -10dB -20dB Trunk Loss Max - 5dB 0.1A / 0.15A Sky UK- EN50607 - EN50494 SCR Mode Legacy Mode Flashing Green Solid Green REC 4 VL HL TERR VH HH Quick Fit Couplers WPSU-2.5A WT51-10WB WM512 WSCR504 WSCR508 SAT: Freq Range 290~2340MHz | Gain 30dB | Slope 12dB±1dB | Max Output 112dBµV TERR: Freq Range 87~790MHz | Gain 24dB | Slope 8dB±1dB | Max Output 112dBµV Quattro and WB compatible TERR 4G 5G WATS-530WB WATS-530WB 4 X IF + TERR Launch Amp EXAMPLE CONFIGURATION Hybrid IRS SPECIFICATIONS Pro-Tap MODEL Frequency Range Dual Satellite Reception Trunk Inputs (F-Type Female) Trunk Outputs (F-Type Female) Tap Outputs (F-Type Female) Gain Gain Control Input Levels Min / Max Trunk Through Loss Return Loss Max Output Level Protean TapTM (Attenuation Switch) Isolation Trunk DC Pass Impedance Compatibility (Auto Switching) SAT Wideband SAT Quattro TERR SAT Wideband (2x WB LNB) SAT TERR SAT TERR SAT TERR SAT TERR SAT Trunk Input / Output TERR Trunk Input / Output Tap Output SAT TERR TERR Trunk Port to Port Tap Port to Port SAT (per trunk) TERR Switching Commands dSCR/Legacy Mode Indication (per port) Power Supply Voltage Powering Power Consumption Min / Max @ 18V Power Indication Masthead Supply (switchable) Earth Terminal Bars (Tap Outputs) Earth Lug Dimensions including Earth Bars W x L x H (mm) Weight Legacy dSCR Via DC In Via SAT Trunks Via Apartment TERR Input Only WSCR504 290-2340MHz 950-2150MHz 87-790MHz YES 4 SAT + 1 TERR 4 SAT + 1 TERR 4 -5dB ~ +25dB (AGC) 8dB±2dB AGC 15dB 64 ~ 104dBV 52 ~ 102dBV <-5dB <-5dB >10dB / >10dB >8dB / >8dB >8dB 89dBV (AGC) 101dBV 0 / -10 / -20dB >36dB >43dB YES (2A Max) NO 75 Legacy SKY UK dSCR EN50607 EN50494 13/18V / 22kHz / DiSEqC DiSEqC LED (dSCR Flash) 18V DC YES YES NO 0.1A / 0.15A LED 12V DC 100mA Fitted Up to 6mm² core 190 x 126 x 43 540g The EU Declaration of Conformity can be viewed at www.whytetechnologies.com. 14 WSCR504 | WSCR506 | WSCR508 | WSCR512 | WSCR516 WSCR506 290-2340MHz 950-2150MHz 87-790MHz YES 4 SAT + 1 TERR 4 SAT + 1 TERR 6 -5dB ~ +25dB (AGC) 8dB±2dB AGC 15dB 64 ~ 104dBV 52 ~ 102dBV <-5dB <-5dB >10dB / >10dB >8dB / >8dB >8dB 89dBV (AGC) 90dBV 0 / -10 / -20dB >36dB >43dB YES (2A Max) NO 75 Legacy SKY UK dSCR EN50607 EN50494 13/18V / 22kHz / DiSEqC DiSEqC LED (dSCR Flash) 18V DC YES YES NO 0.1A / 0.15A LED 12V DC 100mA Fitted Up to 6mm² core 190 x 190 x 43 660g WSCR508 290-2340MHz 950-2150MHz 87-790MHz YES 4 SAT + 1 TERR 4 SAT + 1 TERR 8 -5dB ~ +25dB (AGC) 8dB±2dB AGC 15dB 64 ~ 104dBV 52 ~ 102dBV <-5dB <-5dB >10dB / >10dB >8dB / >8dB >8dB 89dBV (AGC) 90dBV 0 / -10 / -20dB >36dB >43dB YES (2A Max) NO 75 Legacy SKY UK dSCR EN50607 EN50494 13/18V / 22kHz / DiSEqC DiSEqC LED (dSCR Flash) 18V DC YES YES NO 0.1A / 0.15A LED 12V DC 100mA Fitted Up to 6mm² core 190 x 190 x 43 710g WSCR512 290-2340MHz 950-2150MHz 87-790MHz YES 4 SAT + 1 TERR 4 SAT + 1 TERR 12 -5dB ~ +25dB (AGC) 8dB±2dB AGC 15dB 64 ~ 104dBV 52 ~ 102dBV <-5dB <-5dB >10dB / >10dB >8dB / >8dB >8dB 89dBV (AGC) 90dBV 0 / -10 / -20dB >36dB >43dB YES (2A Max) NO 75 Legacy SKY UK dSCR EN50607 EN50494 13/18V / 22kHz / DiSEqC DiSEqC LED (dSCR Flash) 18V DC YES YES NO 0.1A / 0.15A LED 12V DC 100mA Fitted Up to 6mm² core 190 x 255 x 43 880g WSCR516 290-2340MHz 950-2150MHz 87-790MHz YES 4 SAT + 1 TERR 4 SAT + 1 TERR 16 -5dB ~ +25dB (AGC) 8dB±2dB AGC 15dB 64 ~ 104dBV 52 ~ 102dBV <-5dB <-5dB >10dB / >10dB >8dB / >8dB >8dB 89dBV (AGC) 87dBV 0 / -10 / -20dB >36dB >43dB YES (2A Max) NO 75 Legacy SKY UK dSCR EN50607 EN50494 13/18V / 22kHz / DiSEqC DiSEqC LED (dSCR Flash) 18V DC YES YES NO 0.1A / 0.15A LED 12V DC 100mA Fitted Up to 6mm² core 190 x 318 x 43 1300g In the interest of continuous improvement, all specifications of products are subject to change without notice. 15 Unit 1, Watermill Business Centre. Edison Road, Enfield. EN3 7XF Tel: 0330 999 1980 | info@whytetechnologies.com | www.whytetechnologies.com Copyright © Whyte Technologies February 2022