Compliance | Scanstrut
Instruction Manual for SCANSTRUT models including: SC-12V-F1 12v Power Socket, SC-12V-F1, 12v Power Socket, Power Socket, Socket
SC-12V-F1 12V waterproof power socket
Scanstrut Flip Pro 12V Power Socket | 12 Volt Planet
File Info : application/pdf, 1 Pages, 875.90KB
DocumentDocumentFLIP PRO 12V POWER SOCKET - (SC-12V-F1) 17-05-2023 (Issue 2) Installation Instructions Technical information: Parts list: Input voltage 12/24V System 10-15V DC Input current Max Output Type Standby draw Waterproof rating 10 A 12V10A <0.1W IPX4 Front 12V Socket x1 Gasket Front install only x1 Lock Ring x1 For latest tech info visit: www.scanstrut.com/USB READ IMPORTANT SAFETY INFORMATION BEFORE INSTALLING. No.6x20mm Front Fit Bezel x1 Screws x4 Tool list: 32mm (1 1/4") Hole saw Drill Front install only Drill bit 2.5mm (3/32") or 3mm (1/8") Pozi Screwdriver Silicone Certification. Scanstrut Ltd, declares the product `Flip Pro Max' SKU: SC-MULTI-F1 is in compliance with EMC CE-RED Directive (2014/30/EU) & The CE certificate of EN55032, EN55035, EN61000 conformity can be found at www.scanstrut.com/uk/compliance Drilling template: WARNING CHECK SCALE 1:1 1 2 Draw a centre line to align template, ensure line is square on surface and correct orientation. TOP Use drilling template to drill ø32mm (1 1/4") hole (see tools required). 3mm (0.11") Min 25mm (1") Max 55.0mm (2.17") ø32.0mm (ø1.26 ") TOP Ø32mm (1.25") 1mm (6/64") 44.1mm (1.73") BEZEL 51.0mm (2.01") 90° 3 FRONT INSTALL ONLY Drill 2 pilot holes for front fit bezel. 4 Feed Barrel through the gasket and hole. Pilot Hole Size Material Soft Material e.g Plywood Hard Material e.g Fiberglass No. 6 Screw 2.5mm (3/32") 3mm (1/8") 5 REAR INSTALL ONLY Tighten lock ring onto product until FRONT INSTALL ONLY Apply silicone seal on fixings and pilot holes. Place the front fit bezel over charger and fix bezel in place. Make sure the orientation bezel is correct. TOP 6 Connect to 12/24V supply, ensuring a waterproof connection. Fuse and select cable diameter according to input voltage and current for your specific installation. * If using a 24V system a voltage converter is required * 42.0mm (1.65") BEZEL 68.1mm (2.68") WARNING: This product is to be connected to a 12V DC battery power source only. The power supply must be switched off before installation. An appropriate fuse or circuit breaker must be used between the battery / power source and this product. Check for correct polarity of all wiring before switching the power on. This product may contain high voltages. Do not tamper with the product. When used in high ambient temperature or in direct sunlight, the product may turn off temporarily, this is a safety feature of the electronics. The IP protection rating is only valid if the installation is carried out correctly according to the instructions and on a perfectly flat, smooth and non-porous surface. When choosing a mounting location, avoid areas exposed to heat radiation devices and areas with poor ventilation This product is NOT approved for use in hazardous/ flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere e.g. engine room. Before drilling any holes, ensure the area behind the mounting location is clear of wires, fuel and all other hazardous objects. Ensure any holes cut will not significantly weaken the structure of the mounting surface. If the product needs to be mounted outside, it must be mounted in a location safely above the waterline, where it is not at risk of being submerged. CAUTION: This product is to use with 12v cigarette lighter plug only. This product does not contain any user serviceable parts. DO NOT attempt to repair or modify the product in any way. WIRING: Professional electrician installation recommended, see Technical Information for power requirements. To achieve max power output, the specified voltage must be at the charger. Battery performance and voltage drop needs to be considered for installation. ENVIRONMENTAL PROTECTION: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. IMPORTANT: Scanstrut Ltd & Inc. accepts no responsibility for any injuries or other damages arising from the use of their products in any circumstances. WARRANTY: A 2 year, non-transferrable warranty covers this Scanstrut product only and not any devices that are charged by it. No warranty is given for users' devices and users expose their devices to hazards, known or unknown, at their own risk. UK & International +44 (0)1392531280 sales@scanstrut.com For further installation and warranty information please visit: www.scanstrut.com USA +1 860 308 1416 usasales@scanstrut.com