maintained.in
User Guide for FULL SIGNAL models including: S5-A Cell Phone Signal Booster, S5-A, Cell Phone Signal Booster, Phone Signal Booster, Signal Booster, Booster
CEREVO TECHNOLOGY LIMITED S5-A Cell Phone Signal Booster 2BB6MS5-A 2BB6MS5A s5 a
File Info : application/pdf, 17 Pages, 669.79KB
DocumentDocumentINDOOR OUTDOOR S5-A Quick Start Guide How Full Signal Booster Works 1. Outdoor antenna receives outside signal from the nearby cell tower and sends it to Full Signal Booster 2. The booster amplifies the signal and sends to indoor antenna 3. Indoor antenna receives amplified signal and sends it throughout your rooms. 1 3 2 INDOOR OUTDOOR Vice versa, indoor antenna receives cellphone signal and sends to the booster. The booster then amplifies the signal and sends it to outdoor antenna. Outdoor antenna sends signal to the cell tower Then you can make phone calls and internet streaming. Important Knowledge before Installaon In order to make a successful installaon, there is a most crical informaon you need to know- You should Prevent Self-oscillaon during installaon. Self-oscillaon happens when outdoor antenna and indoor antenna are installed too close to each other. When self-oscillaon happens, instead of picking up signal from the Operator Cellular Tower, the outdoor antenna picks up the transmied signal from the indoor antenna, and repeatedly boosted, thus it will generate a signal loop with a lot of noise which is called Self-oscillaon. When self-Oscillaon happens, the booster will not boost useful signal from your cellular operator, so the system will not work. INDOOR OUTDOOR To prevent self-oscillaon during the installaon of a cellular signal booster, it is crucial to follow the given guidelines: 1. Outdoor antenna and indoor antenna need to be separated with an object or a distance. It is essenal to have a physical barrier, such as a wall, between the outdoor and indoor antennas. This helps to prevent the transmied signal from the indoor antenna from being picked up and amplified by the outdoor antenna. 2. Outdoor antenna and indoor antenna should not point to each other: Ensure that the outdoor antenna and indoor antenna are not facing each other directly. This reduces the chances of the outdoor antenna picking up the signal transmied by the indoor antenna. 3. Maintain a minimum required separaon distance: The outdoor antenna should be placed as far away as possible from the indoor antenna to minimize the risk of self-oscillaon. The minimum recommended separaon distances are: Horizontal Distance: 20 feet (6 meters) Vercal Distance: 13 feet (4 meters) Horizontal:>6 meters(20) Vercal:>4 meters(13) By adhering to these guidelines, you can prevent self-oscillaon and ensure that the cellular signal booster funcons effecvely by amplifying the signal from the cellular operator rather than creang a loop with noise. Perfect 1. Point to the tower 2. Antennas back to back 3. Two wall barriers 1 Wrong 2 1. Not poinng to the tower Acceptable 3 1. Point to the tower 2. Antennas back to back 3. No barriers, make sure vercal distance enough Wrong 4 1. Two antennas facing the same direcon 2. Vercal distance might not be enough Package Contents INDOOR OUTDOOR Cellular Signal Booster Inside Antenna 75'& 60' Cables Outside Antenna Power Supply Outside Antenna Mounng Bracket QUICK INSTALLATION GUIDE Select the Locaon for the Outside Antenna Note: This is the most crical step and will determine the performance of your booster. Generally, the strongest signal will be located on the side of your home facing to the nearest cell tower from your cellphone operator. 1) Walk around your house with your cell phone, search for the place where your phone gets the strongest signal recepon, at least 3-4 signal bars. 2) Make a few phone calls there to check the call quality, if it is clear and stable, that will be an ideal posion to place the outdoor antenna Install the Outdoor Antenna Install the outdoor antenna on the roof above the locaon you found in Step 1. Make sure the antenna points towards the direcon where your cellular operator's tower is. Connect the Outdoor cable to the antenna, waterproof the connectors with tapes. Note: 1) The Outdoor Antenna should be as far away as possible from the Indoor antenna. Minimum required separaon distance between indoor and outdoor Antenna: Straight line distanceOver 30 Feet (10 meters), or Horizontal distance: 20 Feet (6 meters ) Vercal distance: 13 Feet ( 4 meters) 2) To prevent lightening, the height of the outdoor antenna should be lower than the highest point of your house. Horizontal:>6 meters(20) Vercal:>4 meters(13) Install the Indoor Antenna INDOOR OUTDOOR Place the indoor antenna at where strong signal is needed most. The Indoor Antenna is a direconal antenna, it needs to be installed on the wall. Choosing a locaon facing all over your home will help to maximize your coverage area. Note: 1) Make sure the Outdoor Antenna and Indoor Antenna are not facing to each other. 2) Make sure there is sufficient separaon between the Outdoor Antenna and Indoor Antenna. Antennas,Power on INDOOR OUTDOOR Connect the Outdoor Antenna cable with "OUTDOOR " port on the cellular booster, and connect the Indoor Antenna cable with "INDOOR " port on the repeater. Then power on the booster and check the coverage. INDOOR OUTDOOR Opmize Coverage RESET Work To opmize coverage for this repeater, follow these steps: 1.Band: It shows the performance status of the booster in each frequency band (700MHz, 700MHz,850MHz, 1900MHz, 2100MHz). Use the "+" or "-" buons to switch between bands. 2.Outdoor Signal Strength: Range from -50~-70. It represents the signal strength your outdoor antenna picked up from outside. Aim for a signal strength of around-60dB or higher. If the signal strength is lower than that, try reposioning or adjusng the outdoor antenna for beer signal recepon. 3.Indoor Signal Strength: Range from 0-20dBm. It indicates the output signal strength produced by the booster. Try to get 10dBm or higher. If it is lower than that, try adjusng the outdoor antenna to improve the signal recepon and increase the coverage area. 4.Uplink/Downlink Gain: The ideal uplink gain is 60dB, and the ideal downlink gain its 70dB. 5.Work Indicator: The normal status of the work indicator is green or orange. If it turns red, it indicates that the separaon between the antennas is not enough on that band, which may result in poor coverage. Increase the distance between the antennas and ensure they are not facing each other to improve coverage. Working Normally Working Normally /ALC Acve Isolaon Alarm Sleep Mode: If there is no operaon for more than 5 minutes, the booster will enter sleep mode to conserve power. Simply touch the screen to resume its operaon. Addional Informaon for Professional Installers (More Sengs): AUTO MODE NANUAL MODE 1.Auto Mode & Manual Mode: Press and hold the "SETTING" buon to switch between auto and manual modes. In auto mode, the booster automacally adjusts the uplink and downlink gain based on the outdoor signal strength. In manual mode, you can adjust the gain sengs manually. 2.Switch Frequency: Use the "+" or "-" buons to switch between frequencies and observe the working informaon. 3.Adjust Gain: In manual mode, press the "SETTING" buon to enter the eding mode. Use the "+" or "-" buons to adjust the uplink and downlink gain sengs. Aer making the desired adjustments, press "RESET" to save the sengs and exit the eding mode. 4.Reset: Press and hold the "RESET" buon to restore the booster to its factory sengs. By following these steps and opmizing the various sengs based on the provided informaon, you can improve the coverage and performance of the booster. SAFTY GUIDLINES Important guidelines and regulaons for the safe and proper use of the cellular repeater. 1.Power Supply: Only use the power supply provided with the repeater package. Using any other power supply may result in improper funconing or damage to the device. 2.Antenna Safety: Ensure that any antenna used with the repeater is located at least 8 inches (20 cenmeters) away from all persons. This is to minimize potenal exposure to radio frequency (RF) energy. 3.Compliance with FCC Rules: The repeater has been tested and found to comply with the limits set for a class B digital device under Part 15 of the FCC Rules. These limits are designed to protect against harmful interference in residenal installaons. 4.Harmful Interference: If the repeater causes interference to network operators or other communicaon systems, it is recommended to take the following measures: Relocate the Outdoor Antenna. Increase the separaon between the Outdoor Antenna and Indoor Antenna. Seek assistance from the supplier or local installers for further guidance. 5.Compliance with Regulatory Requests: If requested by the FCC (or ISED in Canada) or a licensed wireless service provider, it is mandatory to cease operang the device. It is crucial to adhere to these guidelines to ensure proper funconality, minimize interference, and comply with regulatory requirements. If you have any specific concerns or quesons, it is advisable to consult the supplier or seek assistance from local professionals experienced in installing and operang cellular repeaters. Trouble Shoong FAQ Soluon Aer installaon, the signal improvement is not significant, and the indoor coverage area is limited 1. Adjust the posion or direcon of the outdoor antenna, try to get a beer signal recepon. 2.Check if the cables are properly connected. 3. Raise the outdoor antenna so that it can receive beer signal. 4. Replace a higher gain outdoor antenna The phone signal is full, but the call quality is poor Check the booster "Work Indicator" if any of the lights is in red, it indicates that the separaon between the antennas is insufficient. It is essenal to increase the distance between the antennas, or increase physical barriers, such as a wall, between the outdoor and indoor antennas. Make sure the antennas are not facing to each other, then restart the booster. Aer installaon, the signal did not improve, but it was worse Check the booster "Work Indicator" if any of the lights is in red, it indicates that the separaon between the antennas is insufficient. It is essenal to increase the distance between the antennas, or increase physical barriers, such as a wall, between the outdoor and indoor antennas. Make sure the antennas are not facing to each other, then restart the booster. I have been using it normally before, but suddenly the signal is not good aer using it for a period of me 1. Check the cable connecons. 2. Check if the outdoor cable is installed securely without damage. 3. Check if LCD indicator is normal, if it is off, booster device need to be sent to supplier for repair. Product Specificaons Model: S5-A Network: AWS-1/Cellular/Low A-EBlocks/700 M Hz Upper C Block/Broadband PCS Model No. Smart Booster S5-A Working Band UL Frequency Range (MHz) DL Frquency Range (MHz) Low A-E Blocks 700 MHz Upper C Block 699-716 777-787 729-746 746-756 Cellular 824-849 869-894 Broadband PCS AWS-1 1850-1915 1710-1755 1930-1995 2110-2155 Maximum Gain UL70±3 dB DL70±3 dB Maximum Output Power UL: 19±3 DL: 9±3 dBm AGC Range 30dB Ripple in Band 7dB Impedance I/O Port Weight Dimension Power Supply Environmental Condion 50 ohm N-Female Booster Device 2.0Kg Whole Kit 5 kg 180 × 120 × 25 m AC: 110-240 V, 50/60Hz, Output DC 5V/3A Booster: IP40 Antenna: IP65 (1)Usage of unaut horized ant ennas, cables, and/ or coupling devices may result in poor effect and, insevere cases, equipment damage. (2)a complet e list of aut horized ant ennas, cables, and/ or coupling devices: This device complies w it h part 15 of t he FCC Rules. Operat ion is subject t o t he follow ing t w o condit ions: (1) This device may not cause harmful int erference, and (2) t his device must accept any int erference received, including int erference t hat may cause undesired operat ion This equipment should be inst alled and operat ed w it h a minumum dist ance of 20cm bet w een t he radiat or and your body. The ant enna for t he device must be inst alled t o comply w it h t he 10 met er above ground maximum ant enna height limit at ion This equipment complies w it h IC radiat ion exposure limit s set fort h for an uncont rolledenvironment . This equipment should be inst alled and operat ed w it h minimum dist ance of 20 cmbet w een t he radiat or and your body. This t ransmit t er must not be co-locat ed or operat ing inconjunct ion w it h any ot her ant enna or t ransmit t er. This device complies w it h Indust ry Canada licence-exempt RSS st andard(s). Operat ion is subject t o t he follow ing t w o condit ions: (1) This device may not cause int erference, and (2) This device must accept any int erference, including int erference t hat may cause undesiredoperat ion of t he device. Le present appareil est conforme aux CNR d'lndust rie Canada applicables aux appareils radioexempt s de licence. L'exploit at ion est aut orisee aux deux condit ions suivant es: (1) l'appareil ne doit pas produire de brouillage, et (2) 'ut ilisat eur de 'appareil doit accept er t out brouillage radioelect rique subi, meme si lebrouillage est suscept ible d'en compromet t re le fonct ionnement This is a CONSUM ER device. BEFORE USE, you must meet all requirement s set out in CPC-2-1-05. This device M UST ONLY be operat ed w it h approved ant ennas and cables as specified by t he manufact urer. Ant ennas must be inst alled in a w ay w here t he minimum separat ion dist ance bet w een t he ant ennas and a user (or byst ander) specified by t he manufact urer is ALWAYS maint ained.In order t o reduce oscillat ions it is recommended t hat sufficient separat ion dist ance is maint ained bet w een t he donor and server ant ennas of t he zone enhancer syst em.You M UST cease operat ion of t his device immediat ely if request ed by ISED or a licensed w ireless service provider. WARNING:E911 locat ion informat ion may not be provided or may be inaccurat e for calls served by using t his device. Ce produit est un appareil GRAND PUBLIC. AVANT DE L' UTILISER, vous devez vous conformer à t out es les exigences ét ablies dans la CPC 2-1-0. Cet appareil NE DOIT ÊTRE UTILISÉ qu' avec des ant ennes et des câbles approuvés, conformément au x indic at ions du fabricant . Les ant ennes doivent êt re inst allées de manière àce que la dist ance minim ale de sépara t ion ent re les ant ennes et un ut ilisat eur (ou un passant ) spécifiée par le fabricant soit T OUJOURS respect ée.Afin de réduire les oscillat ions, il est recommandéde maint enir une dist ance de s éparat ion suffisant e ent re l es ant ennes du donat eur et du serveur du syst ème d' enrichisseur de zon e.Vous DEVEZ cesser d' ut iliser cet appareil immédiat ement à la demande d' ISDE ou d' un fournisseu rde services sans fil aut orisé. AVERTISSEM ENT:Les informat ions relat ives àla localisat ion pour le service E911 peuvent êt re non fournies ou inexact es pour les appels t ransit ant par cet appareil.This device may operat e in a fixed locat ion only, for in-building use. Cet appareil peut fonct ionner seulement àun emplacement fixe à l' int érieur d' un bât iment . label: CPC-2- 1-05 --Zone Enhancers - Spect rum management and t elecommunicat ions ht t ps:/ / ised-isde.canada.ca/ sit e/ spect rum-management -t elecommunicat ions/ en/ learn-more/ keydocument s/ procedures/ client -procedures-circulars-cpc/ cpc-2-1-05-zone-enhancers CEREVO TECHNOLOGY LIM ITED F22, Tow er B, RuiChuangGuoJi Plaza, No.8 WangJing East Road, Chaoyang Dist rict , Beijing, China 100102 Cont act : Esson Diao Tel: 18218747363 Em ail:619991099@q q .co m