Important Safety Information

• Do not disassemble, repair, or modify the product yourself. Doing so may cause fire, electric shock, or malfunction. For internal inspection and repair, contact the service center.
• If any foreign matter gets inside the product, detach the power cord immediately. Contact the service center for repair.
• Do not adjust the product while driving. Doing so may cause an accident. Stop or park your car in a safe place before installing and setting up the product.
• Do not install the product in a location where the product can interfere with the driver's field of vision. Doing so may cause an accident.
• Do not use a damaged or modified power cord. Only use the cords provided by the manufacturer. Damaged or modified power cords may cause an explosion, fire, or malfunction.
• Do not operate the product with wet hands. Doing so may cause electric shock.
• Do not install the product in an environment with high humidity, or combustible gases or liquids. Doing so may cause an explosion and/or fire.

• Do not leave the product near infants, children, or pets. There is a risk of them swallowing small components, and/or their saliva may get into the product, causing an explosion due to a short circuit.
• Do not spray water or wax directly onto the product while cleaning the inside of the car. Doing so may cause fire, electric shock, or malfunction.
• If smoke or an unusual smell is emitted from the power cord, detach the power cord immediately. Contact the service center or your distributor.
• Keep the terminals of the power cord clean. Failure to do so may cause excessive heat and fire.
• Use the correct input voltage. Failure to do so may cause explosion, fire, or malfunction.
• Plug in the power cord firmly so that it cannot easily be disconnected. Failure to do so may cause fire.
• Do not cover the product with any material. Doing so may cause external deformation of the product or fire. Use the product and peripherals in a well-ventilated location.

Getting Started

Thank you for purchasing this AZDOME dashcam. This instruction manual contains information on how to operate your dashcam. Before using your dashcam, it is recommended to read through this manual to ensure correct usage. To improve the performance of the product, the contents of this manual are subject to change without prior notice.

• A 32GB formatted microSD card is provided with the AZDOME dashcam when the product is purchased. Insert the microSD card into the dashcam and power it up. The microSD card will be initialized.
• Always keep the camera plugged into power, because the camera uses a super capacitor; if there is no power supply, the dashcam cannot power on.
• A Micro-SD card must be inserted before recording can begin. Please insert only a brand name Class-10 or above higher speed Micro-SD card.
• Before first time use, the memory card MUST be formatted in the camera to prevent any errors and for smooth operation. Refer to the relevant page in the manual for formatting instructions.
• Setting Date & Time: Set the correct date/time based on your location under the TIME ZONE SETTING by going to the camera's system settings menu. Refer to the relevant page in the manual for instructions.

Warranty & Customer Support

AZDOME provides a 12-Month limited warranty for its products from the date of purchase, covering defects in materials and craftsmanship. For questions, support, or warranty claims, contact AZDOME at service@azdome.hk with your Order Number.

IMPORTANT: Proof of original purchase (Online order receipt is also accepted) is required for any warranty service. AZDOME can only provide after-sales service for products purchased directly from AZDOME. If the product was purchased from a different seller, please contact them directly for service or warranty issues.

For online user manual, visit the AZDOME website or contact support.

Overview

Specification

Working Temperature: -20°C to 60°C

Product Diagram

The AZDOME M550 dashcam features a main unit with a front-facing camera lens, a rear camera port, and various buttons and ports. The main unit has a screen on one side and a lens on the other. The top edge includes buttons and ports, while the bottom edge has additional ports.

Main Unit Components:

1. Screen
2. Cabin Camera
3. Power Button
4. UP Button
5. OK Button
6. Down Button
7. Mode Button
8. Mic
9. Reset Button
10. Speaker
11. USB Charging Port
12. Rear Camera Port
13. Micro SD Card Slot
14. Rear Camera (external unit)

Screen Indicators (Example Display):

1. Micro SD Card Indicator
2. Motion Detection Indicator
3. GPS Indicator
4. Parking Monitor Indicator
5. WDR Indicator
6. Mic Indicator
7. Date/Time Display (e.g., 09/26/2020 16:12:59)
8. WiFi Indicator
9. Recording Status (REC)
10. Loop Recording Timer (e.g., 00:00:00)
11. Video Resolution (e.g., QHD P30+FHD P30+FHD P30)
12. Exposure Indicator
13. Live Speed Display (e.g., 0KM/H)

KEYS AND FUNCTIONS

Using Your Dash-cam

Installation

1. Insert the Micro-SD card into the Micro SD slot of the dashcam. (Note: please use an A-Brand high-speed Micro SD card, class 10 or above).
2. Connect the magnet GPS mount to the dashcam; connect the cabin camera to the dashcam.
3. Find a suitable place on the windshield that does not obstruct the driver's field of vision. Remove any foreign matter and clean and dry the windshield before installation.
4. Tear off the protective layer of the electrostatic sticker and adhere the electrostatic sticker to the windshield to prevent marks/glue on your windshield after removing it.
5. Connect the power cable to the magnet GPS mount Mini-USB port, and insert the Car Charger into your vehicle's cigarette lighter port.
6. Before rear camera installation, check if the provided cable is long enough to reach the rear camera in your car. Place the rear camera on the rear window or the bumper by using the adhesive stickers or screws provided.
7. Connect the rear camera to the front dash-cam. If connected properly, front, cabin, and rear camera views will be shown on the screen.

For connecting the rear camera for reverse light anode, the connection point is typically inside the rear windshields or inside the license plate area. Connect the positive live line of the reverse light anode.

Power ON/OFF

Once the car starts, the camera will automatically turn on and start recording.

A. Manually

1. To manually turn on, press the power button.
2. To manually turn off, press and hold the power button for at least 2 seconds.

B. Automatically

The camera will power off if the charger cable is disconnected or if the vehicle is turned off.

FUNCTION

1.1 Video Settings

Resolution

Allows choosing the desired video resolution and frames per second (fps). Higher resolution and FPS videos result in smoother videos, but also take more storage space. The video resolution is ONLY for FRONT camera recording.

• 2KP30+FHDP30+FHDP30 (Default)
• FHDP30+FHDP30+FHDP30

Loop Recording - Off/1min/3mins(Default)/ 5mins

When enabled, select the length (1/3/5 min) of each video clip for loop recording. This function allows the Dash-cam to continuously record. The Dash-cam will automatically delete the oldest files when the memory card gets full, allowing continuous recording.

Rear-cam Mirror - On(Default)/Off

When enabled, the Dash-cam screen will display a mirror image, which should match your rear-view mirror.

Motion Detection - On/Off(Default)

Motion detection is a memory-saving feature that only records footage when motion is taking place. This feature should NEVER be enabled while driving, as it can confuse the camera when stopping and starting at lights. This function is designed for surveillance when the car is parked and NOT moving, typically when the user is not inside the car and continuous surveillance is desired.

NOTE: The sensitivity is affected by many factors, and the available distance is about 3 meters. This function will work ONLY when connected to a 3-lead hard-wire kit.

Time Lapse - Off(Default)/On

When enabled, the Dash-cam can sustain a longer operational period while reducing video file size. Video files will be played at high-speed during playback.

Record Audio - On(Default)/Off

• On: The video includes sounds.
• Off: The video is silent.

WDR - On/Off(Default)

Wide Dynamic Range (WDR) processes images to ensure clear recordings in bright and dark light. This allows the Dash Cam to combine multiple images at different levels of brightness to create one superior image.

Frequency - 50HZ/60HZ(Default)

According to the power supply specification used in your country.

• 60 Hz (USA – North America)
• 50 Hz (Europe – Most Asian Countries)

G-Sensor - Off/ High/ Middle(Default)/ Low

The G-sensor is a 3-axis impact gravitational accelerometer, designed to detect physical and gravitational forces on the Dash-cam. Once the G-sensor is triggered due to physical or gravitational impact force on the camera when recording, the current video file will be locked as an emergency file so it won't be deleted by the loop recording function.

Exposure -+2.0,+5/3,+4/3,+1.0,+2/3,+1/3,+0.0(Default)/-1/3,-2/3,-1.0,-4/3,-5/3,-2.0

To adjust video exposure setting for either brighter or darker video according to your preference.

1.2 Playback Mode

• Normal Video: These are video files saved in loop recording mode.
• Locked Video: These are video files that the Dash-cam locks after the car is shocked.
• Picture: Photos taken when in photo mode.

1.3 Parking Monitor

Time-Lapse Parking Monitor

1. When this feature is set to ON and the AZDOME 3-Lead Hardwire Kit is installed properly.
2. When the car's engine is turned OFF and the key is turned to the lock position.
3. The camera will STOP Loop Recording and automatically enter Time-Lapse Parking Monitor mode.
4. While in Time-Lapse Parking Monitor, if someone hits your car, the camera will lock the current video in the LOCK folder, then continue Time-Lapse recording.
5. When the car is started again, the camera will automatically STOP Time-Lapse Parking Monitor mode and return to normal video mode to start loop recording.

6.4 Date/Time Settings

The Timezone must be set first via [System Settings] ➜ [Timezone]. Then set your local date and time.

6.5 Stamp - Off/On(Default)

Time Stamp / GPS Stamp / Speed Stamp: When enabled, this information will be shown on the video or photo.

6.6 Storage

Storage Format Remind: Once a time duration is chosen and this function is turned on, the dash cam will prompt "Please format SD card" to avoid too many locked files interfering with loop recording.

SD Card Format: The Micro SD card must be formatted when inserted for the first time in the Dash-cam. The formatting process ensures the card's file system format is optimized for the camera.

Storage Info: To check the usage of the memory card, format the memory card regularly to ensure enough available space.

6.7 Language - Multilingual, default English.

Allows choosing the desired language for the dash-cam system.

6.8 System Settings

Fatigue Driving Reminder - Off(default)/1hour/2hours/4hours

Once a time duration is chosen and this function is turned on, the dash cam will emit sounds to alert the user.

Speed Unit - KM/H(default)/MPH

Beep Sound - On(default)/Off

To switch on/off or adjust the key tone.

Screen Saver - Off/1 min(Default)/3 mins/5 mins

When enabled, the screen will go black after 1/3/5 minutes of no-operation while the Dash-cam is still on/recording.

IR LED -Auto(Default)/Night Mode/Day Mode

This function works on the cabin camera.

Timezone Setting - UTC/GMT+12 to UTC/GMT-12, Default GMT +8

Before setting Date/Time, set your local Timezone first according to your location, then press "OK" to confirm. The timezone will not change automatically when daylight saving time starts/ends; it must be adjusted manually.

Default Setting

Allows restoring all settings to factory default settings.

GPS Info

Check the satellite number / Longitude / Latitude / Speed.

6.9 Information

To check the current firmware in the Dash-cam. This information is necessary to check if newer version firmware is available for update. Visit www.azdome.hk for the latest firmware.

2. Method of Setting Date/Time.

1. Go into [System Settings], Select [Time Zone], select your local timezone and press OK.
2. Press M to exit, and select [Date/Time], set your local date/time and press OK.

The document includes visual representations of the menu navigation for setting the timezone and date/time. These show a hierarchical menu structure with options like Video Settings, Playback Mode, Park Monitor, Date/Time, WiFi, IR LED, Time Zone, Stamp, Storage, Language, System Settings, and Information. The date/time setting screen shows fields for year, month, day, hour, and minute.

3. Firmware Update

To update to the LATEST firmware version:

1. Download the firmware file from http://www.azdome.hk/downloads.html or contact service@azdome.hk.
2. Copy the firmware file to the Micro SD card ROOT file and insert it into the dashcam.
3. Connect to power supply and power on the dashcam. The light will flash rapidly, and the update will take 1-2 minutes. The dashcam will power on automatically when the update is successful.
4. Check if the firmware version is the latest version.
5. Format the Micro SD Card in the dashcam; otherwise, the Dash-cam will update again on the next power on.

For any problems, contact AZDOME at service@azdome.hk.

4. GPS Track

AZDOME GPS Player

1. Go to the AZDOME website www.azdome.hk/downloads to download the AZDOME Player (For Windows or macOS).
2. Install the AZDOME Player on your laptop.
3. The latitude, longitude, and speed will be embedded in the video.

AZDOME Tech Support: service@azdome.hk

The document includes a diagram illustrating the GPS player interface, showing a map with various locations (e.g., Southport, Preston, Liverpool, Bolton, Bury) and a speedometer/compass display, indicating how GPS data is integrated with video playback.

5. WiFi APP

Downloading AZDOME App On phone

1. Search for "AZDOME" in the App Store or Google Play Store to find the App and then download and install it.
2. Turn on WiFi of the camera: Long press the Down Button (represented by a downward arrow icon) for 2 seconds to turn on the WiFi Mode.
3. Turn on WiFi of your phone and connect: Go to Phone's Settings ➜ WiFi ➜ Select M550_ac64cfe679d Camera's WiFi (WiFi Name SSID: M550_ac64cfe679d, PASSWORD: 12345678).
4. Keep the Dash-cam within 3 meters of your phone. Open the AZDOME App to "Add Device"; the live video of the Dash-cam will be displayed on the AZDOME App upon successful connection. Explore the APP from there.
5. The Dash-cam cannot be operated when connecting WiFi. To disconnect WiFi, long-press and hold the Down Button (represented by a downward arrow icon) for 2 seconds to return to video mode.

6. DISCLAIMER

The videos/pictures taken by the Car dash cam are only for reference. AZDOME does not take any responsibility due to data-loss in abnormal circumstances. Special version: The device records files in normal recording status. However, in the following situations, files may be damaged or lost:

1. If the TF card is pulled out while recording, final video files will be damaged or lost.
2. If there is an illegal blackout during recording, final video files will be damaged or lost.
3. If there is a destructive collision during recording, video and audio files will be damaged or lost.
4. If there is a destructive collision during recording leading to the Memory card becoming loose, video and audio files will be damaged or lost.

7. Notice

ⓒ This product complies with the radio interface requirements of the European Community.

⚖ This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate recycling facility. Recycling helps protect natural resources, human health, and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

Σ Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.