Beaverlab DDL-TW2 Smart Telescope User Manual

Introduction

This document provides comprehensive instructions for the Beaverlab DDL-TW2 Smart Telescope, covering its setup, operation, features, and troubleshooting.

1. Adjustments and Focusing

Pan Tilt Adjustment

To adjust the telescope's view vertically and horizontally, use the pan handle. Release the PTZ locking knob to allow movement.

Horizontal Turning Adjustment

Rotate the telescope horizontally by releasing the PTZ locking knob.

Focusing

To achieve a clear image, adjust the focal length adjustment knob. The image will be focused through this knob.

2. Device Overview and Composition

Use of DS1

The DS1 unit supports both wireless and wired observations. A wired connection requires an OTG adapter and is not supported by Apple systems.

Description of DS1 Composition

The DS1 device features:

• HD touch screen
• Wireless indicator
• Shutter indicator
• Charging indicator
• Dust cap
• TW2 smart astronomical telescope mount

Controls:

• ON/OFF & Shutter keys: Press and hold for 2 seconds to turn the device ON or OFF. A short press activates the shutter to take a photo or video.

3. Components and Accessories

Type-C Interface

The Type-C port is used for charging. The power indicator flashes when the DS1 is at low power and remains solid ON when fully charged. It also facilitates image and video transmission when connected to a computer via software.

Reset Button

Press and hold the Reset button to reset the device. Upon successful reset, the network enters a pending connection state, and indicators flash once.

1/4in Adapter

This adapter allows mounting the device on tripods with standard 1/4in interfaces.

Remote Control

The remote control includes:

• Indicator light
• Return key
• Arrow keys (up, down, left, right) for navigation and mode selection
• Photograph shortcut key

Magnification Reduction Lens

A 0.5x Focal Reduce lens is included for adjusting magnification.

4. Maintenance and Charging

Replacing the Remote Control Battery

Reminder: Ensure the positive and negative terminals of the button battery (CR2032) are oriented correctly, with the positive terminal facing outward.

1. Install the button battery.
2. Fasten the battery compartment cover.

Charging of the DS1

Reminder: The DS1 can be charged using a 5V 2A adapter. Avoid charging for more than 12 hours to preserve battery life.

1. Open the bottom rubber plug.
2. Plug in the Type-C charging cable with the power adapter for charging.

5. Device Operation

ON/OFF

Press and hold the power key for 2 seconds to turn the device ON or OFF.

Shooting

Flip the touch screen to the desired viewing angle to begin shooting.

6. Connection and Shooting Methods

Remote Control Operation

1. Remove the remote control.
2. Switch on the remote control by pressing and holding the ON/OFF & shutter keys for 2 seconds. The remote control will automatically connect to the DS1 when powered on (ensure the remote is close to the camera).

Remote control shooting operation: After successful connection, click the shutter button to shoot. Use the arrow keys to switch between photo and video modes, perform real-time image zoom, and enter the photo album view.

DS1 Direct Operation

Short press the ON/OFF and shutter keys on the DS1 for direct shooting.

Touch Screen Operation

Tap the shooting and video keys on the touch screen to capture photos or videos.

Auto Shutdown

In WiFi or wired connection mode, the device enters standby after 3 minutes of inactivity. A short press of the power/photo key wakes the device. If not woken for over 15 minutes, it will automatically shut down.

7. Touch Screen Interface Functions

The touch screen interface provides access to various functions:

• 1 Video/photo switching: Switch between photo and video modes.
• 2 Photo: Short press to take photos or videos. Files are saved to the album. A warning appears if the memory card is full.
• 3 Album: Allows classification, viewing, previewing, and deletion of pictures and videos.
• 4 Full screen mode: Hides settings and status bars for an unobstructed view, retaining only the exit and photo/video icons.
• 5 More: Access to advanced settings including:
  • Lens switching: Select between wide angle, medium focus, and telephoto lenses.
  • Grid line: Choose from Off, Square grid, or Cross grid.
  • Continuous shooting setting: Configure the number of consecutive shots.
  • Timed photographing: Set a timer for taking pictures.
  • WiFi switch: Turn WiFi connection ON or OFF.
• 6 Image mode: Select from manual, landscape, moon, sports, cloudy, night, or starry night modes.
• 7 Noise reduction: Activates noise reduction for clearer images.
• 8 HDR switch: Enhances image details by reducing over-exposure and under-exposure.
• 9 AI algorithm optimization: Utilizes Wide Dynamic Range (WDR), Motion-Compensated Temporal Filtering (MCTF), and Defogging (DF).
• 10 Timer continuous shooting state: Displays the current count for continuous shots.
• 11 WiFi State: Indicates the status of the WiFi connection (normal or disconnected).
• 12 Remote control connection state: Shows the connection status between the DS1 and the remote control. If disconnected, check the remote's power or proximity.
• 13 Memory card state: Displays the used and maximum capacity of the memory card.
• 14 Power level state: Shows the current battery level.

8. Mobile Phone and PC Connectivity

Mobile Phone Wireless Connection

1. APP Download and Installation:

• Ensure the DS1 is fully charged before use. For extended observation, it can be charged using mobile charging banks.
• Scan the provided QR codes (for Android and iOS) to download the "Beaver Point" app from the respective app stores.

2. Equipment Connection:

• Connect to the WiFi network named "DDL-TW2-XXXXXX" with the password "12345678".
• Start the "Beaver Point" app, select the "Smart Telescope Finder TW2" (e.g., DDL-TW2-XXXXXX), and connect.
• Click the "Start Observation" button on the home page to enter the real-time transmission interface.

PC Wired Connection

1. Connect the PC to the DS1 using a USB cable.
2. Once the software detects the USB port, click the "Image Transmission" button in the pop-up window.
3. Open the Windows software and select the device to begin observation.

9. Astronomical Observation

Moon Observation Guideline

1. On a clear night, ensure the device is fully charged and connect it to your mobile phone for real-time image transmission.
2. To search for the moon, turn on the red dot finderscope, locate the red dot, and use the finderscope to align with the moon's center by adjusting the PTZ.
3. Adjust the focus knob until the image of the moon is clear.

For observing other celestial bodies, manually locate them using astrolabe-type software or a configured star-finding disc.

The astronomical telescope is equipped with a compass. Combined with the complimentary Planisphere, you can confirm the current sky chart and search for specific stars or nebulae.

10. Accessories and Tools

The package includes the following accessories:

• DS1 unit
• Solar Filter
• Data Cable
• Planisphere
• Carry Bag
• Tripod
• Optical Tube
• Finder Scope
• Remote Control
• Manual
• 0.5x Focal Reduce lens

11. Faults and Troubleshooting

The Smart Telescope is a precision optical device. For optimal performance, ensure it is used correctly.

General Care:

• When not in use, cover the lens cap to protect it from dust. Use a lens brush or air blower for dust removal.
• Avoid using chemical lens cleaning solutions, as they may damage optical parts.
• Keep the telescope in a cool and ventilated place.

12. Trademark and Legal Statements

"Beaverlab" is a trademark of Beaverlabtech Limited Liability Company. Unauthorized use is prohibited.

This manual is copyrighted by Beaverlabtech Limited Liability Company. Reproduction or distribution without permission is prohibited.

FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to conditions that prevent harmful interference. Any modifications not expressly approved may void the user's authority. The equipment has been tested and found to comply with Class B digital device limits, designed for reasonable protection against interference. If interference occurs, measures like reorienting the antenna, increasing separation, or using a different circuit may help. The device meets general RF exposure requirements for portable use.

13. Product Specifications and Precautions

Battery Precautions

• The product uses rechargeable batteries.
• Rechargeable batteries must be charged under adult supervision.
• Use the recommended charger.
• Do not short circuit power supply electronics.

Global Parameters

14. Product Information and Contact

Product Name: Smart Telescope (Finder TW2)

Product Model: DDL-TW2

Product Net Weight: About 3.8kg

Product Size: 1300x1140x1030mm

Brand Company: Beaverlabtech Limited Liability Company

E-mail: support@beaverlabtech.com

Website: www.beaverlabtech.com

YouTube: Beaverlab YouTube Channel

Instagram: @beaverlabtech

Twitter: @BEAVERLABOS

Facebook: BeaverLAB US Facebook

Input Voltage: DC5V 2A

Operating Temperature: -10°C to 45°C

FCC ID: 2A6VM-DDL-TW2

By scanning the QR code, users can download the app, get exclusive benefits, and unlock more ways to play.