Global Support｜Audio-Technica Corporation オーディオテクニカ
User Manual for audio-technica models including: AE5100, Cardioid Condenser Instrument Microphone
Fixed-charge back plate, permanently polarized condenser. Cardioid. 20 - 20,000 Hz. 80 Hz, 12 dB/octave. -36 dB (15.8 mV) re 1V at 1 Pa. 150 ohms.
User Manual Cardioid Condenser Instrument Microphone AE5100 Features Notes on use 0 Connection procedure This product requires 48 V DC phantom power. Output terminals PIN1 (ground) PIN3 (cold) PIN2 (hot)
File Info : application/pdf, 2 Pages, 340.84KB
DocumentDocumentUser Manual
Cardioid Condenser Instrument Microphone AE5100
Thank you for purchasing this product. Before using the product, read through the user manual to ensure that you will use the product correctly. Please keep this manual for future reference.
Features
· Uncompromising sound quality for overheads, percussion, acoustic guitar, strings and other acoustic instruments
· Large-diaphragm capsule delivers accurate and natural response · Low-profile design permits innovative placement options previously unattainable with a
large-diaphragm condenser · Robust design for enduring dependability on the road · Integral 80 Hz HPF switch and 10 dB pad · Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation
of desired sound source
Notes on use
The AE5100 is intended for use in professional applications where remote power is available. It requires 11V to 52V DC phantom power, which may be provided by a mixer or console, or by a separate, in-line source such as the Audio-Technica AT8801 single channel or CP8506 four-channel phantom power supplies.
Output from the microphone's XLRM-type connector is low impedance (Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground (shield). Output phase is "Pin 2 hot" positive acoustic pressure produces positive voltage at Pin 2. An integral 80 Hz hi-pass filter provides easy switching from a flat frequency response to a low-end roll-off. The roll-off position reduces the microphone's sensitivity to popping in close vocal use. It also reduces the pickup of low-frequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically-coupled vibrations.
The AE5100 includes an AT8471 isolation clamp to provide secure mounting, versatile positioning, and effective dampening of unwanted mechanical noise.
Avoid leaving the microphone in the open sun or in areas where temperatures exceed 43°C for extended periods. Extremely high humidity should also be avoided.
Safety precaution
Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product.
Cautions for the product
· Do not subject the product to strong impact to avoid malfunction. · Do not disassemble, modify or attempt to repair the product. · Do not handle the product with wet hands to avoid electric shock or injury. · Do not store the product under direct sunlight, near heating devices or in a hot, humid or
dusty place.
Connection procedure
Connect the output terminals of the microphone to a device that has a microphone input (balanced input) compatible with a phantom power supply. The output connector is an XLRM-type with polarity as shown in the figure below.
Output terminals
PIN1 (ground)
PIN2 (hot)
PIN3 (cold)
This product requires 48 V DC phantom power.
Specifications
Element Polar pattern Frequency response Low Frequency response Open circuit sensitivity
Impedance Maximum input sound level
Noise Dynamic range (typical)
Signal-to-noise ratio Phantom power requirements
Switch
Weight (less accessories) Dimensions
Output connector Included accessories
Fixed-charge back plate, permanently polarized condenser Cardioid 20 - 20,000 Hz 80 Hz, 12 dB/octave -36 dB (15.8 mV) re 1V at 1 Pa 150 ohms 148 dB SPL, 1 kHz at 1% T.H.D. 158 dB SPL, with 10 dB pad (normal) 11 dB SPL 137 dB, 1 kHz at Max SPL 83 dB, 1 kHz at 1 Pa 11-52 V DC, 3.2 mA typical High-pass filter, 10 dB pad (normal) 143 g 148.5 mm long, 26.0 mm maximun diameter
Integral 3-pin XLRM-type AT8471 isolation clamp for 5/8"-27 threaded stands; 5/8"-27 to 3/8"-16 threaded adapter; AT8136 windscreen; soft protective pouch
· 1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL * Typical, A-weighted, using Audio Precision System One. For product improvement, the product is sublect to modification without notice.
Polar pattern
0°
330°
30°
300°
60°
270°
90°
240°
120°
210°
180°
150°
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
200 Hz 1 kHz 5 kHz 8 kHz
Response in dB
Frequency response
20
10
0 10 dB
-10
-20
-30
50
100
200
500
1k
2k
5k
10k
20k
Frequency in Hertz
LEGEND
0°, 50cm Roll-off
Audio-Technica Corporation 2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
©2017 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com
05-DEC--2020 Form No.ATGC-L0384-20
AE5100
· · · · · 80Hz 10dB ·
AE5100 11V 52V AT8801 CP8506
XLRM2 31()2
80Hz ()
AE5100AT84715/8"-27
43°C
· · · ·
XLRM
1
2
48V
3
()
()
20 - 20,000 Hz 80 Hz12 dB/octave -36 dB15.8mV) 1V 1Pa 150 148 dB , 1 kHz 1% T.H.D. 158 dB , 10 dB () 11 dB
137 dB, 1 kHz 83 dB, 1 kHz 1 Pa 11-52V3.2mA 10 dB 143 148.5 mm, 26.0 mm 3
AT8471 5/8-27 ; 5/8-27 3/8-16 AT8136
· 1 10 / 10 94 dB SPL *A Audio Precision System One
0°
330°
30°
300°
60°
270°
90°
240°
120°
210°
180°
150°
5
200 1 5 8
dB
20
10
0 10 dB
-10
-20
-30
50
100
200
500
1k
2k
5k
10k
20k
0°50
Audio-Technica Corporation 2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
©2017 Audio-Technica Corporation
www.at-globalsupport.com
05-DEC-2020 Form No.ATGC-L0384-20