MikroTik CRS418-8P-8G-2S+RM

Safety Information:

• Before you work on any MikroTik equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing accidents. The installer should be familiar with network structures, terms, and concepts.
• Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
• This equipment is to be installed by trained and qualified personnel, as per these installation instructions. The installer is responsible for making sure, that the Installation of the equipment is compliant with local and national electrical codes.
• Do not attempt to disassemble, repair, or modify the device. If service is needed, please contact MikroTik support.
• This product is intended to be installed indoors. Keep this product away from water, fire, humidity, or hot environments.
• We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your own risk!
• The socket-outlet shall be installed near the equipment and shall be easily accessible.
• In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power adapter from the power outlet.
• This is a Class A product. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate measures.
• To avoid contamination of the environment, separate the device from household waste and dispose of it in a safe manner, for example, in designated areas. Become familiar with procedures for properly transporting the equipment to designated collection points in your area.
• Electric shock hazard if AC input is to be used. This equipment is to be serviced by trained personnel only!

Technical Specifications:

CE Compliance:

CE Declaration of Conformity: Hereby, Mikrotīkls SIA declares that the equipment type CRS418-8P-8G-2S+RM is in compliance with Directive 2014/30/EU and 2014/35/EU and 2011/65/EU (RoHs), including Commission Delegated Directive (EU) 2015/863. The full text of the EU declaration of conformity is available at the following internet address: https://mikrotik.com/products. This declaration is only valid for Mikrotīkls SIA (MikroTik) products (including, combinations of software, firmware and hardware) provided by Mikrotīkls SIA (MikroTik) authorized partners to the end customer directly for use within the EU or countries that have implemented the EU Directives and/or spectrum regulation. Any Mikrotīkls SIA (MikroTik) products not obtained from Mikrotīkls SIA (MikroTik) authorized partners may not comply with EU Directives and Mikrotīkls SIA (MikroTik) makes no assurances for such products.

Manufacturer: Mikrotīkls SIA, Ūnijas iela 2, Riga, Latvia, LV1039.

Federal Communication Commission Interference Statement:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance.

Innovation, Science and Economic Development Canada:

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. This Class A digital apparatus complies with Canadian ICES-003.