ICON DynaMic 7B

Important Safety Instructions

CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN.

ATTENTION: POUR EVITER LES RISQUES DE CHOC ELECTRIQUE: NE PAS ENLEVER LE COUVERCLE. AUCUN ENTRETIEN DE PIECES INTERIEURES PAR L'USAGER. CONFIER L'ENTERETIEN AU PERSONNEL QUALIFIE.

AVIS: POUR EVITER LES RISQUES D'INCENDIE OU D'ELECTROCUTION, N EXPOSEZ PAS CET ARTICLE A LA PLUIE OU A L'HUMIDITE.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure. The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance instructions.

1. Read this manual thoroughly before using this unit.
2. Keep this manual for future reference.
3. Take notice of and comply with all warnings included in the user's manual or indicated on the appliance.
4. Follow all instructions included in this manual.
5. Do not expose this unit to rain or moisture. Avoid having water or other liquids spilled on this unit.
6. Do not block any ventilation openings or interfere with the proper ventilation of this unit. Install in accordance with the manufacturer's instructions.
7. Do not use or store near any heat sources such as radiators, heat registers, stoves, or other heat-producing appliances.
8. To avoid the risk of electrical shock, do not touch any exposed wiring while the unit is in operation.
9. Only use attachments/accessories specified by the manufacturer.
10. Unplug this unit and all connected electrical equipment during lightning storms or when left unused for a long period of time.
11. Refer all servicing to qualified service personnel. Servicing is required when the appliance has been damaged in any way or fails to operate normally.

WARNING: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture.

Introduction

Congratulations on your purchase of the ICON Pro Audio DynaMic dynamic microphone! This manual provides a detailed description of the features of the DynaMic dynamic microphone and a full list of specifications.

Please register your product on our website at: www.iconproaudio.com/registration.

We strongly recommend retaining the original packaging. In the unlikely event that the product is returned for servicing, the original packaging (or a reasonable equivalent) is required. With proper care and adequate air circulation, your DynaMic microphone will operate flawlessly for many years to come.

We trust this product will provide years of excellent service. In the unlikely event that your product does not perform to the highest standard, every effort will be made to address the issue.

What's in the package?

• DynaMic microphone
• Shock Mount (attached)

[Image Description: A black, large-bodied dynamic microphone with a mesh grille and an attached adjustable mount.]

Register Your ICON ProAudio Product to Your Personal Account

1. Check Serial Number of Your Device

   Please go to http://iconproaudio.com/registration or scan the QR code below.

   [Description of QR Code: A 2D barcode linking to the ICON ProAudio registration page.]

   Input your device's serial number and other information on the screen. Click "Submit". A message will pop up showing your device information such as model name and its serial number. Click “Register this device to my account”. If you see any other message, please contact the after-sales service team.

2. Log In or Sign Up

   Existing user: Please log into your personal user page by inputting your username and password.

   New user: Please click "Sign Up" and fill in all the information.

3. Download Useful Materials

   All your registered devices will show on the page. Each product will be listed with available files such as drivers, firmware, user manuals in different languages, and bundled software for download. Please ensure you download the necessary files, such as drivers, before beginning device installation.

Features

The DynaMic7B is a large-bodied dynamic microphone, perfect for vocal applications. It is ideal for high-quality live streaming, podcast, or broadcast applications, in addition to capturing any number of sources. Its robust exterior is matched by its good looks. The internal pop shield minimizes plosive consonants, resulting in a smooth, open, natural, and rich sound. The attached swing mount allows for flexible positioning. High-quality components and architecture ensure every detail of your voice is captured intricately.

Switches on the rear of the DynaMic7B offer the user both a low cut filter (to reduce low-frequency rumble) and a high-mid boost (to increase 'presence'). The DynaMic is versatile and can be used on any number of sources for a fully rounded and detailed sound, including sung vocals at close proximity. Despite its origins as a broadcast mic, this style of mic is favored by bands, vocalists, and rappers alike. It is suitable anywhere you need warmth, smooth detail, and intelligibility.

• High degree of clarity and quality for all manner of vocal applications.
• Ideal as a broadcast microphone suited to radio, podcasts, and streaming.
• Cardioid pickup pattern for outstanding sound source separation and feedback rejection.
• Pressure-gradient transducer with shock-mounted capsule.
• Ultra-rugged construction with an all-metal finish.
• Attached swing mount allows for flexible positioning.
• Internal pop filter – no need for external pop shields.
• Exceptional build quality.
• Robust, high-grade XLR connector at the rear.
• Low cut filter switch (300 Hz).
• High boost switch (1KHz - 7KHz).

Operating the DynaMic

Setting Up the Signal Level

When connecting the DynaMic7B to a mixer or recorder input, ensure the input level is suitable. Most quality mixers and recorders offer a microphone input with a MIC trim (Gain) control. The purpose of the MIC trim control is to optimize the signal-to-noise ratio. A good MIC preamplifier with trim typically includes a Peak or Clip LED. To set a good level on the DynaMic7B, position it in front of the desired sound source (e.g., a presenter talking) and slowly raise the MIC trim control until the Peak LED lights up. Then, turn the trim control down until the LED no longer lights. The ideal setting is to turn the trim control up as much as possible without lighting the Peak LED.

Microphone Placement

To maximize sound quality, pay careful attention to the placement and positioning of your DynaMic. All microphones, especially cardioid microphones, exhibit a phenomenon known as the “proximity effect”. This is a change in the frequency response of a microphone based on the position of the MIC capsule relative to the sound source. When you point a cardioid MIC directly at the sound source (on-axis), you get the best frequency response. When pointing the microphone slightly away (off-axis), you will notice a drop in low frequencies, making the microphone sound thinner.

For most vocal applications, position the microphone directly in front of the presenter. If the voice sounds overly 'bassy', try switching the low cut on and repositioning the mic. If the voice needs more 'presence', switch on the 'high boost' switch.

Connecting the DynaMic7B

The DynaMic7B features an XLR connection, providing a balanced output. Unlike condenser mics, you do not need to use 'phantom power' when connecting with an 'XLR to XLR' cable. Simply plug directly into your device, and the microphone will work.

You will need a standard 3-pin XLR cable and an audio-interface, such as the ICON Duo 44, to connect to your computer for recording. You can then use the microphone to record to a Digital Audio Workstation (DAW) like Cubase, Harrison Mixbus 32C, or Pro Tools.

You can also use a device such as ICON Pro Audio's 'Live Console', specifically designed for live streaming. Find out more here: https://iconproaudio.com/product/live-console/.

The Switches

The low cut and high boost switches on the rear of the microphone can be operated with your finger. The window below the switches indicates the EQ change. When both switches are off, a straight line is displayed. When the low cut is switched on, the window displays a low cut shelf (a slope veering to zero on the left). When the high boost switch is on, the EQ setting displays a 'bell' shape, indicating a 'boost' in the upper-mid frequencies.

[Diagram Description: Three images showing the rear of the microphone with different switch settings.]

• No EQ: Both switches off.
• Low Cut: Low cut switch engaged.
• Mid-High Boost: High boost switch engaged.

The bass roll-off is at 400Hz and the mid-high frequency boost is at 1KHz – 7KHz.

Specifications

[Diagram Description: A frequency response graph showing output level versus frequency for different settings.]

[Diagram Description: A polar pattern diagram illustrating the microphone's sensitivity at different angles.]

Services

If your DynaMic7B needs servicing, follow these instructions.

Check our online Help Center at http://support.iconproaudio.com for information, knowledge, and downloads such as:

• FAQ
• Download
• Product Registration
• Video Tutorials

If you don't find a solution, create a support ticket at our online Help Center. Our technical support team will assist you as soon as possible.

Navigate to http://support.iconproaudio.com and sign in to submit a ticket. Once submitted, our support team will help resolve the problem with your ICON ProAudio device.

To Send Defective Products for Service:

1. Ensure the problem is not related to operation error or external system devices.
2. Keep this owner's manual. It is not required for repair.
3. Pack the unit in its original packaging, including end card and box. If you have lost the packaging, ensure the unit is packed properly. ICON is not responsible for any damage occurring due to non-factory packing.
4. Ship to the ICON tech support center or the local return authorization. See service centers and distributor service points at the link below.

Service Centers:

• US:
  North America
  Mixware, LLC – U.S. Distributor
  3086 W. POST RD.
  LAS VEGAS NV 89118
  Tel.: (818) 578 4030
  Contact: www.mixware.net/help
• Europe:
  Sound Service GmbH
  European Headquarter Moriz-Seeler-Straße3 D-12489 Berlin
  Telephone: +49 (0)30 707 130-0
  Fax: +49 (0)30 707 130-189
  E-Mail: info@sound-service.eu
• Hong Kong:
  ASIA OFFICE:
  Unit F, 15/F., Fu Cheung Centre,
  No. 5-7 Wong Chuk Yueng Street,
  Fotan,
  Sha Tin, N.T., Hong Kong.
  Tel: (852) 2398 2286
  Fax: (852) 2789 3947
  Email: info.asia@icon-global.com

For additional update information, please visit our website at: www.iconproaudio.com.

Connect with ICON Pro Audio

[Description of QR Codes: Multiple QR codes are displayed linking to various ICON Pro Audio social media and support platforms.]

• Twitter: www.twitter.com/iconproaudio
• Instagram: www.instagram.com/iconproaudio
• Facebook: www.facebook.com/iconproaudio
• YouTube: www.youtube.com/iconproaudio
• Website: www.iconproaudio.com
• Support: support.iconproaudio.com
• Dashboard: iconproaudio.com/dashboard/