Instruction Manual for Zigbee models including: Namron, ZigBee, 1 kanal bryter, K2, sort
ZigBee dimmer switch based on ZigBee 3.0. • Enables to pair ZigBee lighting devices via touchlink commissioning without coordinator.
TouchLink to a Zigbee Lighting Device. LED indicator. 5. Removed from a Zigbee Network through Coordinator or Hub Interface.
10. Find and Unbind a Zigbee Lighting Device 11. Clear All Find and Bind Mode Paired Lighting Devices 12. Setup a Network & Add Devices to the Network (No Coordinator or Hub Required)
File Info : application/pdf, 3 Pages, 2.12MB
DocumentDocumentNamron ZigBee 1 kanal bryter K2 sort 09.ZGK2D.04837 Important: Read All Instructions Prior to Installation Function introduction Press and hold down both keys together to search and pair to ZigBee network or factory reset the dimmer switch. Click to turn on/off the paired lighting devices 11 mm Front side 71.20 mm 55.57 mm Press and hold down to decrease/increase light intensity of the paired lighting devices Note: This switch supports 1 group for binding max. 30 lighting devices. Product Data Protocol ZigBee 3.0 Operation Voltage 3VDC (CR2450) Transmission Frequency 2.4GHz Transmission Range (free field) 30m Protection Type IP20 Dimming Range 0.1%-100% · ZigBee dimmer switch based on ZigBee 3.0 · Enables to pair ZigBee lighting devices via touchlink commissioning without coordinator · Supports find and bind mode to pair with ZigBee lighting devices in the same network · Supports 1 group for binding max. 30 lighting devices · 2.4 GHz global operation · Long battery life mesh technology · Transmission range up to 30m · Compatible with universal ZigBee Gateway products · Compatible with universal single color ZigBee lighting devices · Compatible with universal ZigBee dimmable lighting devices Dimensions 71.2x71.2x13.6mm ZigBee Clusters Supported by This Remote Are As Follows: Input clusters: · Basic · Power Configuration · Identify · Diagnostics Output clusters: · Identify · On/off · Level control · Ota Safety & Warnings · This device contains a button lithium battery that shall be stored and disposed properly. · DO NOT expose the device to moisture. Quick Start (Simplified operations compared to standard operations in the part "Operation") Network pairing mode: click both buttons 3 times (the remote should not belong to any gateway network). 71.20 mm 55.57 mm Battery: CR2450 Before the first use, please open the battery cover and remove the protective film Back side Factory reset: click both buttons 3 times (the remote should already be paired to a gateway). Operation 1.This ZigBee dim remote is a wireless transmitter that communicates with a variety of ZigBee compatible systems. This transmitter sends wireless radio signals that are used to remotely control a compatible system. 2.This ZigBee remote supports 1 group for binding max. 30 lighting devices and enables to control single color ZigBee lighting devices. 3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network) Step 1: Remove the remote from previous zigbee network if it has already been added to it, otherwise pairing will fail. Please refer to the part "Factory Reset Manually". LED indicator Step 2: From your zigbee controller or hub interface, choose to add device or accessory and enter Pairing mode as instructed by the controller. Step 3: Press and hold down both until LED indicator turns on. Step 4: Immediately short press to search nearby network, indicator flashes every 1 second, 20 seconds timeout if there is no network. Indicator will then blink 5 times quickly for successful pairing. Note: 1) After pairing successfully, the remote information will appear on the controller or hub interface. 2) No remote information will appear on the hub interface if pairing to Philips Hue Bridge. 4. TouchLink to a Zigbee Lighting Device Step 1: Set the zigbee lighting device to start TouchLink commissioning, please refer to its manual to learn how. LED indicator Step 2: Bring the remote within 10cm of the lighting device. < 10cm ZigBee Lighting Device Step 3: Press and hold down both until LED indicator turns on. Step 4: Immediately short press twice to start TouchLink commissioning of the remote. LED indicator flashes fast for 3S, then flash 6 times slowly to indicate successful pairing and the light connected to the device will blink twice. Note: 1) Directly TouchLink (both not added to a ZigBee network), each remote can link with 30 devices. 2) TouchLink after both added to a ZigBee network, each remote can link with max. 30 devices. 3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink. 4) After TouchLink, the remote can control the linked lighting devices. 5. Removed from a Zigbee Network through Coordinator or Hub Interface From your ZigBee controller or hub interface, choose to delete or reset the remote as instructed, indicator flashes 3 times quickly to indicate successful removing. 6. Factory Reset Manually Step 1: Press and hold down both until LED indicator turns on. LED indicator Note: All configuration parameters will be reset after the remote is reset or removed from the network. Step 2: Immediately short press 5 times continuously, indicator flashes 3 times quickly to indicate successful reset. 7. Remove a Touchlink Paired ZigBee Lighting Device LED indicator Step 1: Set the Touchlink paired zigbee device to start TouchLink commissioning, please refer to its manual to learn how. Step 2: Bring the remote within 10cm of the lighting device. < 10cm ZigBee Lighting Device Step 3: Press and hold down both until LED indicator turns on. Step 4: Immediately short press 3 times to start TouchLink removing of the remote. LED indicator flashes fast for 3S, then flash 6 times slowly to indicate successful removing. 8. Factory Reset a Lighting Device (Touch Reset) Note: the device shall be added to a network, the remote added to the same one or not added to any network. LED indicator Step 1: Set the zigbee device to start TouchLink commissioning, refer to its manual. Step 2: Bring the remote within 10cm of the lighting device. < 10cm ZigBee Lighting Device Step 3: Press and hold down both until LED indicator turns on. Step 4: Immediately short press 4 times to start Touch Reset of the remote. LED indicator flashes fast for 3S, then flash 3 times slowly to indicate successful reset. 9. Find and Bind a Zigbee Lighting Device Note: Make sure the device and remote already added to the same zigbee network. Step 1: Start find and bind mode on the Zigbee lighting device (initiator node) and enable it to find and bind target, refer to its manual. LED indicator ZigBee Lighting Device Step 2: Press and hold down both until LED indicator turns on. Step 3: Short press to enable the remote (target node) to find and bind initiator.LED indicator flashes 4 times for successful binding or twice if binding fails. Note: Each remote can bind max. 30 lighting devices. 10. Find and Unbind a Zigbee Lighting Device LED indicator Step 1: Start find and bind mode on the Zigbee lighting device (initiator node) and enable it to find and bind target, refer to its manual. Step 2: Press and hold down both until LED indicator turns on. 11. Clear All Find and Bind Mode Paired Lighting Devices LED indicator ZigBee Lighting Device Step 3: Short press twice to enable the remote (target node) to find and unbind initiator. LED indicator flashes 4 times for successful unbinding or twice if unbinding fails. Installation 1.Remove battery insulator Use tool to open the silicone gel battery cover 2.Install the controller to wall(2 methods) Pull out the battery insulator Install the silicone battery cover back Step 1: Press and hold down both until LED indicator turns on. Step 2: Short press 5 times continuously to clear all bound lighting devices . LED indicator flashes 4 times for successful unbinding. 12. Setup a Network & Add Devices to the Network (No Coordinator or Hub Required) Step 1: Factory reset the remote and the lighting device, refer to their manuals. LED indicator Step 2: TouchLink the remote and device to setup a network, refer to their manuals. < 10cm ZigBee Lighting Device Step 3: Short press button to enable the network to discover and add devices, LED indicator will flash twice. 180 seconds timeout, repeat the operation. Step 4: Set another remote into network pairing mode and pair it to the network, refer to its manual. Step 5: Add more remotes to the network as you would like. Step 6: Factory reset the lighting devices that you would like to add to the network, refer to their manuals. Step 7: Touchlink to pair the added remotes and lighting devices you would like to add, the devices will be added to the network through Touchlink, refer to their manuals. 13. OTA The remote supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically. 14. How to Check Whether the Remote Belongs to a Network or not Short press any button, indicator blinking means the remote has already been added to a network. No blinking of indicator means the remote does not belong to any network. 15. Battery Power Monitor Function The remote will report battery power value to the coordinator under following situations: · When powered on. · When short pressing both and buttons simultaneously. · When operating the switch to send data packets (over 4 hours since last operation). · When added to the network by a coordinator. Method 1:Stick 3M glue on the back of the bracket and then stick the bracket to the wall Method 2:Screw the bracket to the wall After the bracket is fixed,clip the frame and control part to the bracket in sequence Mounting The key part of this controller is an universal one, especially rotary standard switch element that can be integrated in numerous frames by different manufactures as below list: BEKER GIRA JUNG MERTEN S1, B1, B3, B7 glass Standard55, E2, Event, Esprit A500, Aplus M-smart, M-Arc, M-Plan Importer: Namron AS Nedre kalbakkvei 88B 1081 Olso Norway Made in ChinaCorel PDF Engine Version 14.0.0.653