Husky 2000 Lumens Rechargeable Work Light

Use and Care Guide

Model #: EL2206 | Item #: 1008 838 992

For questions, problems, or missing parts, contact Husky Customer Service:

8 a.m. - 7 p.m., EST, Monday - Friday | 9 a.m. - 6 p.m., EST, Saturday

Safety Information

WARNING: Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.

Ensure the switch is in the off-position before connecting to a battery pack, picking up, or carrying the appliance. Carrying the appliance with your finger on the switch or energizing an appliance with the switch on invites accidents.
Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperatures above 130°C (265°F) may cause explosion.
Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated in the instructions for use and care.

WARNING: When using flashlights or lanterns, additional precautions should always be followed, including the following:

To reduce the risk of injury, close supervision is necessary when a product is used near children.
Do not contact hot parts.
Only use attachments recommended or sold by the manufacturer.
Do not use in the rain.
To reduce the risk of electrical shock, do not put the work light in water or other liquid.
Do not place or store the product where it can fall or be pulled into a tub or sink.
WARNING: To reduce the risk of injury, do not stare at the operating lamp. Serious eye injury could occur.
WARNING: Do not use the magnet for horizontal overhead mounting.

SAVE THESE INSTRUCTIONS.

Warranty

The manufacturer warrants the product to be free from defects in materials and workmanship for a period of three (3) years from the date of purchase. We take pride in the design and construction of each of our products and work to maintain the quality of our materials and craftsmanship to assure your satisfaction.

If any problems appear, the purchaser may return the item, freight prepaid, together with a copy of your original purchase receipt to the place of purchase, and it will be replaced with the same or comparable model free of charge. This warranty does not cover fixtures that have been altered in any way; it is void if damage or defect has resulted from accident, abuse, misuse, or faulty repair.

In no event will the manufacturer be liable for any incidental or consequential damages. No charge will be acceptable for unauthorized repairs, parts, or service. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. Legal warranty rights will vary from state to state, and you may have other rights.

Contact the Customer Service Team at 1-888-HD-HUSKY or visit www.HUSKYTOOLS.COM.

Specifications

Product Weight	1.79 lb	Input Voltage	DC5V
Product Width	7.81 in.	Input Current	2A
Product Depth	2.30 in.	Power	20W
Product Height	7.32 in.	Recharge time	6hrs
Run Time	High: 3hrs / Medium: 6hrs / Low: 12hrs	Lumen Output	High: 2000lm / Medium: 1000lm / Low: 500lm

Parts Description

The work light includes the following parts:

A: Work light body
B: Charging indicator (LEDs)
C: ON/OFF switch
D: Magnet (located on the base/stand)
E: Protective cap (covering the charging port)
F: USB input socket (Type C)
G: USB output socket (Type A)
H: Stand
I: USB cable

Visual Description: The work light is a rectangular device with a prominent LED panel. It features a robust stand at the base, which incorporates magnets for attachment to metallic surfaces. A protective cap covers the USB-C charging port. The Husky logo is visible on the product.

Pre-Operation

Charging the product

NOTES:

Remove all packaging materials from the product.
Before use, recharge the rechargeable battery. The charging process takes about 6 hours. The rechargeable battery is integrated into the base of the product.
Fully charge the rechargeable battery prior to first use.
Charge the battery if it becomes empty (indicated by only 1 LED of the charging indicator [B] flashing).
Open the protective cap [E].
Connect the USB plug of the USB cable [I] to the USB input socket (Type C) [F] on the product. The USB cable is for charging only.

NOTES: The battery charging status is shown by the charging indicator [B]. Under an input current of 2A, the charging time is approximately 6 hours when the battery is drained.

Operation

1. Using as an LED light

Fully charge the product as described in the "Charging the product" section.

The product can be operated in 4 different modes. Select these by repeatedly pressing the ON/OFF switch [C]:

Press 1x: Work light 100% brightness
Press 2x: Work light 50% brightness
Press 3x: Work light 25% brightness
Press 4x: Flash mode
Press 5x (or after 30s in any mode): Switch off the light

2. Using as a charger

The work light can be used to charge small electronic devices via the USB output socket (Type A port). The charging current required by the device must not exceed 2A. Carefully read the instructions for use of the device you wish to charge.

Adjusting the light direction

To adjust the light direction, rotate the stand [H] and the work light body [A] to a suitable position.

The stand [H] can be rotated 270 degrees.
The work light body [A] can be rotated 360 degrees.

Visual Description: The work light is mounted on a stand. The stand allows for rotation of the light head to direct the illumination as needed.

Magnets

The product is equipped with 4 magnets [D] at the bottom of the stand. These magnets allow the product to be attached to magnetisable surfaces.

Care and Cleaning

WARNING: Always make sure that the worklight is cooled down before attempting to clean it.

Clean the device regularly with a non-abrasive cleaner.
Allow the work light to cool down completely before storing.
Store in a safe place, out of the reach of children.

Maintenance

When the device is not in use, it is recommended that the battery is charged at least every 3 months to maintain battery health.

	Husky 800 Lumen Rechargeable LED Detachable Tripod Light - Use and Care Guide Comprehensive guide for the Husky 800 Lumen Rechargeable LED Detachable Tripod Light, covering safety, specifications, installation, operation, and troubleshooting. Learn how to set up, use, and maintain your Husky LED worklight.
	Husky 1000 Lumen Rechargeable Utility Light with Bluetooth Speaker - Use and Care Guide Comprehensive use and care guide for the Husky 1000 Lumen Rechargeable Utility Light with Bluetooth Speaker. Includes safety information, operating instructions, charging, maintenance, troubleshooting, and warranty details.
	Husky SD 4000 Couplings: Heavy-Duty Stainless Steel Pipe Couplings An overview of Husky SD 4000 couplings, detailing their heavy-duty stainless steel construction, applications, product variations, and certifications. Includes a size and torque chart.
	Husky 8-in-1 Portable Power Source Use and Care Guide (Model HD7481-B) This guide provides instructions for the Husky 8-in-1 Portable Power Source (Model HD7481-B). It covers safety precautions, operation of jump starting, air compression, power inversion, USB charging, LED lighting, hand generator, and recharging. Includes specifications, maintenance, troubleshooting, and application lists.
	Husky OSFS009-WM Compact Refrigerator - Technical Specifications and Product Information Detailed technical specifications, features, energy ratings, and safety information for the Husky OSFS009-WM compact refrigerator. Includes dimensions, capacity, performance data, and handling guidelines.
	Husky 120-Volt Inflator Use and Care Guide This guide provides instructions for the safe and effective use and care of the Husky 120-Volt Inflator (Model #H120N). It includes safety precautions, operating instructions for inflating tires and other items, maintenance, troubleshooting, and recommended tire pressures.
	Husky UltraShot Injection System Hot Runner Service Manual This service manual provides detailed instructions for the installation, removal, maintenance, and safe operation of the Husky UltraShot Injection System hot runner. It includes technical specifications, safety warnings, and troubleshooting guidance for industrial injection molding applications.
	Altanium Delta5 User Guide Comprehensive user guide for the Husky Altanium Delta5 temperature control system, detailing setup, operation, safety procedures, and maintenance for industrial applications in injection molding.