VEIKOUS Aluminium Greenhouse Assembly Instructions

Introduction & Contact Information

This document provides assembly instructions for the VEIKOUS Aluminium Greenhouse. Please read the entire instruction carefully before assembly. It is highly recommended to familiarize yourself with the parts and double-check the appropriate parts for each step.

Contact VEIKOUS:

Website: www.veikous.com
Email: customerservice@veikous.com

Important Information for Contacting Support:

Please have the following information ready when you contact VEIKOUS:

Order number or PO number (found on your invoice, receipt, or platform account).
The model number of the product (printed on the package box).
Description of the part from the parts list.

Due to busy lines, email contact is preferred for quicker assistance.

STOP: Missing or Damaged Parts

STOP

MISSING A PART? CALL US BEFORE GOING BACK TO THE STORE.

The store where you made your purchase does not stock parts for this item. If you have assembly questions or are missing or have damaged parts, please call 1-858-324-1911 (Mon - Sun, 10:00 am to 7:00 pm EST) or email customerservice@veikous.com.

Assembly Tips & Safety Information

Read the entire assembly manual, paying special attention to the important tips and safety information.
Ensure there are no missing pieces by first separating and identifying all parts.
Make sure to check packing material for small parts that may have fallen out during shipment.
Important Note: Structures are not intended for public use. VEIKOUS does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
This manual contains helpful information concerning assembly preparation, installation procedure, and required maintenance.
Always keep safety in mind as your structure is being built.
Keep these instructions for future reference.

Care and Warning

Do not use this product in extreme weather. It will cause product damage directly or shorten product service time drastically in extreme weather.

Bolts can loosen over time. Be sure to check bolts occasionally, tightening at least twice a year. Check all screws for tightness before and during usage of the unit.

Due to the nature of metal, surface oxidation (rusting) will occur once protective coatings are scratched.

Recommendations for Increasing Wind Rating

For areas with strong winds, rain, and snow, consider the following:

Bolt the greenhouse down to the ground with either a concrete slab, base plates, or flanged feet.
Using extra tie-down kits.
Using silicone sealant to seal the panels.
Fix wood planks or boards (NOT INCLUDED) with screws on the roof and side walls (as highlighted in diagrams) of the greenhouse to enhance the wind resistance level.

Parts List: Aluminium Parts

No.	Picture Description	Qty.
1	Long aluminium profile	2
2	Long aluminium profile	2
2A	Aluminium profile with channel	2
2-1	Aluminium profile with holes	6
3	Base aluminium profile	2
4	Base aluminium profile	2
5A	Vertical aluminium profile	2
5B	Vertical aluminium profile	2
6	Angled aluminium profile	2
7	Angled aluminium profile	2
7A	Roof ridge aluminium profile	2
7-1	Roof ridge connector	4
8	Gable end aluminium profile	2
9	Gable end aluminium profile	2
12	Horizontal aluminium profile	1
13	Horizontal aluminium profile	1
14	Roof support aluminium profile	1
15	Roof support aluminium profile	1
16	Vertical support post	14
17	Roof edge aluminium profile	10
18A	Roof edge reinforcement profile	2
18B	Roof edge reinforcement profile	2
19	Aluminium connector profile	8
21	Roof vent support profile	1
22	Roof vent support profile	2
23	Gutter aluminium profile	2
23A	Gutter connector profile	1
23-1	Ridge connector profile	2
24	Aluminium connector	2
25A	Door frame vertical profile	1
25B	Door frame vertical profile	1
26A	Door frame horizontal profile	1
26B	Door frame horizontal profile	1
27	Door hinge component	4
28	Door hinge component	2
30-1	Window frame component	2
30-2	Window frame component	4
30-3	Window frame component	2
30-4	Window latch/handle component	2
31	Door handle	1
31A	Door handle	1
H	Plastic component	3

Parts List: Plastic Parts

No.	Picture Description	Qty.
32	Plastic corner foot	4
33A	Plastic roof connector	2
33B	Plastic roof connector	2
34	Plastic roof connector	2
A6	Hinge component	2

Parts List: Hardware

No.	Picture Description	Qty.	Size
42	Screw	146	M6*15
44	Screw	16	M6*30
45	Screw	30	M6*35
46	Nut	68	M6 nut
47	Self-tapping screw	4
48	Screw	16
F1	Screw	20

Parts List: Twin PC Board

No.	Picture Description	Qty.
A	Rectangular PC panel	16
B	Rectangular PC panel	14
C	Rectangular PC panel	8
D	Rectangular PC panel	2
E	Triangular PC panel	4
F	Pentagonal PC panel	1
I	Triangular PC panel	1
J	Rectangular PC panel	2
K	Rectangular PC panel	4
L	Rectangular PC panel	2

Assembly Instructions

Note: Diagrams show parts and connections. Follow the sequence carefully.

Step 1: Base Frame Assembly

Assemble the base frame using aluminium profiles 1, 2, 2A, 2-1, 3, and 4, secured with hardware 45 (screws) and 46 (nuts). This step involves connecting multiple profiles to form the rectangular base structure.

Step 2: Pre-Assembled Base Frame Installation

Install the assembled base frame onto the plastic corner feet (part 32). Secure the feet to the base frame corners using hardware 42 (screws). Ensure the frame is level.

Step 3-1: Back Wall Frame Assembly

Attach vertical profiles 5A and 5B to the base profiles 3 and 4 using hardware 42. This forms the initial uprights for the back wall.

Step 3-2: Back Wall Frame Assembly

Insert roof support profiles 14 and 15 between the top ends of vertical profiles 5A and 5B, securing them with hardware 42. This creates the upper structure for the back wall.

Step 3-3: Back Wall Assembly

Slide PC panels C into the channels of the assembled back wall frame. Secure them using connector profiles 19 and hardware 42.

Step 3-4: Back Wall Frame Assembly

Continue reinforcing the back wall frame by adding more profiles and connectors (parts 14, 15, 19) and securing with hardware 42, integrating the PC panels.

Step 3-5: Back Wall Assembly

Install PC panels D, E, and F into the upper section of the back wall frame. Use roof vent supports (part 22) and hardware 42 to secure these panels and complete the back wall structure.

Step 3-6: Back Wall's Plastic Parts and Gable Frame Assembly

Attach plastic roof connectors (parts 33A and 33B) to the top of the back wall structure. Assemble the gable frame using profiles 8 and 9, connectors 19, and roof vent supports 22, securing with hardware 42.

Step 3-7: Back Wall's Plastic Parts and Gable Frame Assembly

Connect the assembled gable frame to the back wall structure. The main frame of the greenhouse begins to take shape, including the roof apex support.

Step 4-1: Front Wall Frame Assembly

Similar to the back wall, assemble the front wall frame using vertical profiles 5A and 5B, base profiles 3 and 4, and hardware 42.

Step 4-2: Front Wall Frame Assembly

Install horizontal profiles 12 and 13 at the top of the front wall vertical profiles, securing with hardware 42.

Step 4-3: Front Wall Assembly

Slide PC panels C into the channels of the front wall frame and secure with connector profiles 19 and hardware 42.

Step 4-4: Front Wall Frame Assembly

Continue reinforcing the front wall frame with additional profiles and connectors (parts 12, 13, 19) and hardware 42.

Step 4-5: Front Wall Assembly

Install PC panels E into the upper section of the front wall frame, securing them as needed.

Step 4-6: Front Wall's Plastic Parts and Gable Frame Assembly

Attach plastic roof connectors (parts 33A and 33B) to the front wall structure. Assemble the front gable frame using profiles 8 and 9, connectors 19, and roof vent support 21, securing with hardware 42.

Step 4-7: Front Wall's Plastic Parts and Gable Frame Assembly

Connect the front gable frame to the front wall structure. The main structure, including front and back walls and gable ends, is now largely assembled.

Step 5-1: Side Roof Ridge Assembly

Assemble the side roof ridge components using profiles 6, 7, 7A, 7-1, and hardware 44. This creates the central ridge line for the roof.

Step 5-2: Pre-Assembled Side Roof Ridge Installation

Install the assembled side roof ridge onto the greenhouse structure. Connect it to the gable frames and side walls using parts 6, 7, 7A, 2A, and hardware 42. Note the use of plastic part 33B as a connector.

Step 6-1: Middle Roof Ridge Assembly

Assemble the middle roof ridge components using profiles 23, 23A, 23-1, and hardware 42. This forms the apex of the roof.

Step 6-2: Window Assembly

Assemble the window frames using parts 30-1, 30-2, 30-3, and 30-4. Secure the window frame components using hardware 48. This step involves drilling holes in part L.

Step 6-3: Pre-Assembled Middle Roof Ridge Installation & Window Assembly

Install the assembled middle roof ridge onto the greenhouse. Note: Windows (assembled in Step 6-2) must be slid into the gutter of frame 23 before assembling frame 23.

Step 7-1: Side Wall Assembly

Prepare to install the PC panels for the side walls. The diagram shows panels labeled 'A' being positioned.

Step 7-2: Side Wall Frame Assembly

Install vertical support posts (part 16) along the sides of the greenhouse structure. Secure them using hardware 42. Important: Do not tighten screws completely at this stage; final tightening should occur after PC boards are installed.

Step 7-3: Side Wall Assembly

Install the PC panels (labeled 'A') onto the side wall frames. The diagram shows multiple panels being fitted.

Step 8-1: Roof Wall Assembly

Begin assembling the roof structure. The diagram shows PC panels labeled 'B' being attached to the roof frame.

Step 8-2: Roof Wall Frame Assembly

Continue building the roof frame using profiles 17, 18A, 18B, 24, and hardware 42. Important: Do not tighten screws completely at this stage; final tightening should occur after PC boards are installed.

Step 8-3: Roof Frame Assembly

Further assemble the roof frame using hardware F1 and plastic component H. This step reinforces the roof structure.

Step 8-4: Roof Wall Assembly

Install remaining PC panels (labeled 'B', 'J') and window components (part 30-4) onto the roof structure. Secure with hardware F1.

Step 9: Door Assembly

Assemble the door frames using vertical profiles 25A, 25B, horizontal profiles 26A, 26B, door hinge components 27, 28, PC panels K, and hardware 46, 37. This forms the two halves of the door.

Step 10: Door Assembly

Attach the door handles (parts 31 and 31A) to the assembled doors. Note: The door handles are secured with self-tapping screws (47) (no drilling required).

Step 11: Door Assembly

Attach the door hinges (part A6) to the doors using screws (F1). The doors are now ready to be mounted onto the greenhouse.

Final Check

Check and tighten all screws to ensure that the greenhouse is sturdy.

For better shopping experience, please visit our website: WWW.VEIKOUS.COM

Scan for Installation Video [QR Code Placeholder]

	Veikous Cedar Poly Greenhouse Assembly Instructions and Guide Comprehensive assembly instructions and guide for the Veikous Cedar Poly Greenhouse, including parts lists, hardware details, and site preparation tips. Learn how to build your greenhouse efficiently and safely.
	Veikous Aluminium Greenhouse Assembly Instructions Comprehensive assembly instructions for the Veikous Aluminium Greenhouse, including parts lists, step-by-step guidance, and care recommendations.
	VEIKOUS Cedar Poly Greenhouse Assembly Manual and Guide Detailed assembly instructions and preparation guide for the VEIKOUS Cedar Poly Greenhouse. Includes parts lists, step-by-step instructions, and contact information for support.
	VEIKOUS PG0101-12 Greenhouse Assembly Instructions and Guide Comprehensive assembly guide for the VEIKOUS PG0101-12 Polycarbonate Greenhouse. Includes parts list, step-by-step instructions, and tips for enhancing wind resistance.
	VEIKOUS Aluminium Greenhouse Assembly Instructions Detailed assembly guide for the VEIKOUS Aluminium Greenhouse (Model PG0101-23GY-1), covering parts identification, step-by-step construction, safety tips, and structural reinforcement recommendations.
	Veikous Aluminium Greenhouse Assembly Instructions Comprehensive assembly instructions for the Veikous Aluminium Greenhouse, including parts lists, step-by-step guidance, and care recommendations.
	VEIKOUS 8x6 Polycarbonate Greenhouse Assembly Manual & Installation Guide Comprehensive assembly and installation guide for the VEIKOUS 8x6 Polycarbonate Greenhouse. This manual provides step-by-step instructions, safety advice, and maintenance tips for setting up your hobby greenhouse.
	VEIKOUS Aluminium Greenhouse Assembly Instructions Comprehensive assembly instructions for the VEIKOUS Aluminium Greenhouse, detailing parts, hardware, and step-by-step guidance for construction.