ENGO Controls - Heating control
User Guide for ENGO models including: EREL1ZB12A Smart Relay ZigBee 12A, EREL1ZB12A, Smart Relay ZigBee 12A, Relay ZigBee 12A, ZigBee 12A
EREL1ZB12A - ENGO
File Info : application/pdf, 2 Pages, 940.16KB
DocumentDocumentRELAY EREL1ZB12A | Smart Relay ZigBee, 12A Quick Guide Ver. 2 Release date: II 2023 Producer: Engo Controls S.C. 43-200 Pszczyna Górnolska 3E St. Poland Distributor: QL CONTROLS Sp z o. o. Sp. k. 43-262 Kobielice Rolna 4 St. Poland www.engocontrols.com Introduction The product is designed for intelligent control devices that need to be controlled over voltage-free signal. The voltagefree output makes also possible to control devices which require 230V voltage. The size of the module allows to place it in a flushmounted installation box. It can be used as a boiler control relay for heating system (,,normally open" output logic). It works according to programmed schedules or scenarios (e.g. work dependent on the actions of others system elements, such as a window/door opening sensor or temperature controller). EREL1ZB12A can be controlled remotely (via smartphone and Engo Smart/Tuya app) or locally using a bistable/monostable switch. The relay is equipped with the ENGO binding function, to connect it wirelessly witch selected thermostats (e.g. EONE) in Online or Offline modes. WARNING: This product must be used together with a EGATEZB ZigBee gateway (purchased separately). Product Compliance This product complies with the following EU Directives: 2014/30/EU, 2014/35/EU, 2014/53/EU i 2011/65/EU. Safety Information: Use in accordance with national and EU regulations. Use the device only as intended, keeping it in a dry condition. The product is for indoor use only. Installation must be carried out by a qualified person in accordance with national and EU regulations. Technical specifications Power supply Max load Communication Output Input Dimension [mm] 230V AC 50Hz 12A ZigBee 3.0 2,4GHz COM / NO (Volt-free) S1 (Volt free) 48 x 48 x 20 Installation: Installation must be performed by a qualified person with appropriate electrical qualifications, in accordance with the standards and regulations in force in a given country and in the EU. The manufacturer is not responsible for non-compliance with the instructions. WARNING: For the entire installation, there may be additional protection requirements, which the installer is responsible for. Input/Output EREL1ZB12A 1 2 5 34 1. Power supply 230V AC 2. Volt free output 3. Volt free input 4. Function button 5. LED diode indicating the status of the module LED diode indications EXPLANATION LED diode flashes quickly on red ... The device is in pairing mode with the ZigBee network (when the device does not has been previously added to the ZigBee network , or after restoring factory settings) LED diode flashes slowly on red ... The device is in binding mode (when the device has been previously added to ZigBee network) LED diode lights up green Relay of the module has been turned ON Button functions EXPLANATION Press1time Controlofthemodulesrelay(ON/OFF) Press quickly 5 times Enables binding process (to link EMODZB with thermostat) Press and hold Relay reset (module will be approx. 8 seconds removed from the ZigBee until the LED will start i network and automatically will flashing red go into pairing mode) Connection description a) Connection diagram for gas boiler EREL1ZB12A L COM output NO N S1in ZigBee BOILER CONNECTION* AC 230V L N b) Connection diagram for lighting AC 230V L N EREL1ZB12A L COM output NO N S1in ZigBee bistable / monostable switch c) Connection diagram for pump / actuator EREL1ZB12A L COM output NO N S1in ZigBee AC 230V L N Legend: Boiler connection* -Boiler's contacts for ON/OFF thermostat (according to the boiler's instructions) L, N 230V AC power supply Pump COM,NO Voltage-free output Valve actuator SL in 230V AC voltage output Fuse Installation thermostat in the app Make sure your router is within range of your smartphone. Make sure you are connected to the Internet. This will reduce the pairing time of the device. STEP 1 - DOWNLOAD ENGO SMART APP Download the ENGO Smart app from Google Play or Apple App Store and install it on your smartphone. STEP 2 - REGISTER THE NEW ACCOUNT To register a new account, please follow the steps below: 1 2 STEP 3 - CONNECT THE RELAY TO ZigBee network After installing the application and creating an account, follow these steps: 1 2 Make sure ZigBee gateway has been added to the Engo Smart app. Make sure the relay is connected to the power supply. The LED should flash quickly on red. If not, hold down the button for about 8 seconds. The relay will enter pairing mode. 3 4 In the app, click on upper right corner. 5 Select: ,,Add Device". 6 Click ,,Register" to create new account. 3 Enter your e-mail address to which the verification code will be sent. 4 Enter the verification code received in the email. Remember that you only have 60 seconds to enter the code!! Then set the login password. When the ZigBee gateway finds the relay correctly click the ,,Add" button. 7 Name the device and click,,Done". 3 The relay has been installed and displays the main interface. BINDING thermostat with the module/relay Make sure that the relay and thermostat are in the same ZigBee network (they are added to the same gateway EGATEZB). 1 2 10 sek. 5x clik To properly bind thermostat with the relay first click quickly the button on the device 5 times. The LED diode will start flashing slowly on red, which means the device will enable binding mode. 3 10 sek. On the EONE controller, hold and buttons and for 10 at the same time seconds until the,,bind" function appears. 4 Release the keys, binding function (process of linking thermostat with control box) is active. 5 The,,binding"process takes up to 300 seconds. 6 3 After successfull binding operation,,End"message will be displayed. LED on the module will stop flashing. Both devices have been successfully linked. Thermostat displays the main screen, icon '' '' appeared on the screen indicating connection with the receiver. ATTENTION: If the binding process fails, it must be repeated taking into account the distances between devices, obstacles and local radio signal interferences. Remember: Radio range can be increased by Engo ZigBee repeaters. Factory reset To reset the device, press and hold the function button for approx. 8 seconds until the LED flashes red. The relay will be removed from the ZigBee network and gateway, then goes into pairing mode. Now it's possible to add the relay again (see STEP 3 - CONNECT THE RELAY TO ZigBee network). 8 sek.