EdgeLock® SE051 Ι IoT Secure Element product family | NXP SemiconductorsEdgeLock SE051H | IoT Secure Element for Matter Onboarding via NFC | NXP Semiconductors
User Guide for NXP models including: OM-SE051ARD-H, EdgeLock SE051H, Arduino Compatible Development Kit, EdgeLock SE051H Arduino Compatible Development Kit, OM-SE051ARD-H Arduino Compatible Development Kit, OM-SE051ARD-H EdgeLock SE051H Arduino Compatible Development Kit, Compatible Development Kit, Development Kit
OM-SE051ARD-H Development Board for EdgeLock SE051H Secure Element | NXP Semiconductors
File Info : application/pdf, 6 Pages, 4.68MB
DocumentDocumentQuick Start Guide OM-SE051ARD-H EdgeLock® SE051H Arduino Compatible Development Kit PLUG & TRUST DEVELOPMENT PLATFORM Quick Start Guide Get to know the OM-SE051ARD-H board Please visit www.nxp.com/SE051H for more information. Quick Start Guide Jumper Description Configuration Default J6, J7 Antenna 1-2: via DB15 connector 2-3: Internal antenna J6 1-2, J7 2-3 (no antenna) J9, J10 I2C Master pull up connection Open: not connected 1-2: 3k3 Ohm Open J12 Reset 1-2 RST on J11:3 2-3 RST on Arduino 2-3 J13 SE051_ENA pin routing 1-2: ENA low, VOUT not connected to VIN 2-3: ENA controlled by Arduino pin J1:6 2-3 J14 SE051_VCC pin routing 1-2: Routed to VDD supply voltage (see J19) 3-4: Routed to SE_Vout pin 1-2 5-6: Routed to J11:4 pin J15 I2C Slave SDA connection 1-2: Arduino R3 J4:5 3-4: Arduino R3 J2:9 3-4 J16 SE051_Vin supply 1-2: Supplied by J11:2 pin 2-3: Supplied by the VDD (see J19) 2-3 J17 I2C Slave SCL connection 1-2: Arduino R3 J4:6 3-4: Arduino R3 J2:10 3-4 J18 SE051_IO2 routing 1-2: Routed to J11:9 2-3: Routed to J2:3 1-2 J19 VDD supply voltage 1-2: From LDO 2-3: From 3V3_ARD pin 2-3 1-2: From 5V_PC (USBI2C flat connector) J24 VDD supply selection for LDO 3-4: From 5V_DB15 pin (if LDO is used - see J19) 5-6: From 5V_ARD pin J37, J38 I2C Slave bus pull up configuration Open: 3k3 Ohm (I2C fast mode) 1-2: 660 Ohm (I2C high speed mode) 1-2 Open Quick Start Guide Connect OM-SE051ARD-H to i.MX 8M board MCIMX8M-EVK Please also visit www.nxp.com/SE051H for documentation. Quick Start Guide Connect OM-SE051ARD-H to i.MX 8M Mini 8MMINID4-EVK Connect OM-SE051ARD-H to i.MX 8M Nano 8MNANOLPD4-EVK Please also visit www.nxp.com/SE051H for documentation. EdgeLock SE051H Visit www.nxp.com/SE051H for more information about the SE051H product range. SUPPORT Visit www.nxp.com/support for a list of phone numbers within your region. WARRANTY Visit www.nxp.com/warranty for complete warranty information. Get Started Download installation software and documentation at www.nxp.com/SE051H Reference documents: nxp.com: AN13539, OMSE05xARD Hardware Overview www.nxp.com/SE051H NXP, the NXP logo and EdgeLock are trademarks of NXP B.V. All other product or service names are the property of their respective owners. © 2023 NXP B.V. Part Number: OM-SE051ARD-H