Autel MaxiSys MS909CV

PRODUCT DESCRIPTION

The MaxiSys MS909CV offers comprehensive functionality and online repair information for vehicle diagnostics, fault identification, and repair research. It features a powerful octa-core processor and a 9.7-inch TFT-LCD capacitive touchscreen for efficient diagnosis and clear viewing. This intelligent diagnostics and information system not only displays relevant repair fixes and cases from experienced industry experts but also provides step-by-step guidance for accurate and efficient repairs.

The MaxiSys MS909CV consists of three main components:

• MaxiSys Display Tablet: The central processor and monitor for the system.
• VCI: Vehicle communication interface.
• B200: Battery & electrical system tester.

MaxiSys Display Tablet Components:

• 1. 9.7" TFT-LCD Capacitive Touchscreen
• 2. Ambient Light Sensor: Detects ambient brightness.
• 3. Power LED
• 4. Front Camera
• 5. Microphone
• 6. Speaker
• 7. Collapsible Stand: Extends from the back to allow hands-free viewing of the tablet.
• 8. Rear Camera
• 9. Camera Flash
• 10. Headphone Jack
• 11. USB Port
• 12. USB Port
• 13. Mini USB Port
• 14. HDMI (High-Definition Multimedia Interface) Port
• 15. Mini SD Card Slot
• 16. DC Power Supply Input Port
• 17. Lock/Power Button: Long press to turn on/off the Display Tablet, or tap to lock the screen.

MaxiFlash VCI

Component Descriptions:

• 1. DC Power Supply Input Port
• 2. Vehicle Data Connector
• 3. Ethernet Port
• 4. Vehicle LED
• 5. Connection LED
• 6. Power LED
• 7. USB Port

LED Description

WARNING: Compatible with Autel main cable V2.0 ONLY.

WARNING: Compatible with Autel USB cable V2 ONLY.

MaxiBAS B200

Component Descriptions:

• 1. Power Button
• 2. Status LED
• 3. Power LED
• 4. USB Port
• 5. Battery Clamp Cable
• 6. Aviation Plug
• 7. Positive Clamp Cable Port
• 8. Negative Clamp Cable Port

LED Description

GETTING STARTED

IMPORTANT: Before operating or maintaining this unit, please read these instructions carefully, and pay extra attention to the safety warnings and precautions. Failure to use this product properly may cause damage and/or personal injury and will void the product warranty.

WARNING: The MaxiFlash VCI is compatible with Autel main cable V2.0 and USB cable V2 only.

Establishing Vehicle Communication

1. Connect the main cable V2.0 to the Vehicle Data Connector on the VCI unit and tighten the thumb screws.
2. Connect the cable's 16-pin adapter to the vehicle's DLC, which is usually located under the vehicle's dashboard.
   * Choose an adapter (Deutsch-6, Deutsch-9) according to the diagnostic connector in the vehicle.
3. Power up the tablet. Ensure the tablet is sufficiently charged or is connected to the DC power supply.
4. Select one of the three methods shown below (Bluetooth, Wi-Fi or USB cable V2) to connect the tablet with the VCI device and establish a communication link. Only use the supplied USB cable when programming.
5. When the VCI device is properly connected to the vehicle and the tablet, the VCI status button on the bottom bar of the screen will display a green badge indicating the platform is ready to start vehicle diagnosis.

Inspecting the Battery

Before starting a test, observe the battery for:

• Cracking, buckling or leaking. If any of these defects are observed, replace the battery.
• Corroded, loose or damaged cables and connections. Repair or replace as needed.
• Corrosion on the battery terminals, and dirt or acid on the case top. Clean the case and terminals using a wire brush and a mixture of water and baking soda. Wear protective glasses and gloves when working with batteries.

IMPORTANT: Please ensure that the MS909CV is powered ON when pairing the device and during registration.

Connecting to a Battery

1. Press and hold the Power Button to turn on the MS909CV. Ensure that the unit is sufficiently charged before using.
2. Enable Bluetooth on the MS909CV.
3. Open the Battery Test app and follow the on-screen instructions to pair the MS909CV with the B200 via Bluetooth.
4. Connect the red clamp to the positive (+) terminal and the black clamp to the negative (-) terminal of the battery.

Connecting the Multimeter

1. Plug the red test lead into the red input of the multimeter, and the black test lead into the black input.
2. Connect the red alligator clip/red probe to the other end of the red test lead, and the black alligator clip/black probe to the black test lead.
3. Power on the MS909CV and tap the Multimeter button to enter the application.
4. Connect the multimeter to the multimeter cable port of the MaxiBAS B200 Series Tester and tighten the connector of the multimeter.
5. To use the current clamp with the multimeter when performing the in-vehicle test, tap the Settings icon. Locate the Current clamp on the menu list and swipe the toggle button to the ON position.
6. Plug the red output cable into the red input of the multimeter, and the black output cable into the black input. Connect the multimeter to the MaxiBAS B200 Series Tester and tighten the connector of the multimeter.

Thank you for purchasing this AUTEL MaxiSys MS909CV. Our tools are manufactured to a high standard and when used according to these instructions and properly maintained will provide years of trouble-free performance.