Product Patent
Installation Guide for COMMSCOPE models including: SFG23RHDXL-15-4-126 Line Card Sector Frame, SFG23RHDXL-15-4-126, Line Card Sector Frame, Card Sector Frame, Sector Frame, Frame
SFG23RHDXL15-4-126 | CommScope
File Info : application/pdf, 5 Pages, 1.58MB
DocumentDocument4 3 1.0 GENERAL NOTES 1.1 ALL METRIC DIMENSIONS ARE IN BRACKETS [X.X] 1.2 FOR PATENT INFO: https://www.cs-pat.com 2.0 DESIGN NOTES 2.1 ANY HAZARDS OR OBSTRUCTIONS TO THE CLIMBING FACILITY AND SAFETY CLIMB MUST BE IDENTIFIED PRIOR TO INSTALLING THE APPURTENANCE. ADDITIONAL PRODUCTS MAY BE REQUIRED TO MAINTAIN THE INTEGRITY OF THE SAFETY CLIMB. DURING INSTALLATION, TEMPORARY AND/OR PERMANENT PRECAUTIONARY MEASURES SHOULD BE TAKEN TO PRESERVE THE CLIMBING FACILITY AND/OR SAFETY CLIMB. D 2.2 UP TO 5.0° TAPER AVAILABLE ON MODELS THAT SUPPORT ADJUSTMENT 3.0 MANUFACTURING/SPECIAL REQUIREMENTS 3.1 TIGHTEN ALL BOLTS SECURING FLAT PLATES BY THE TURN-OF-NUT METHOD. TIGHTEN ALL U-BOLTS USING TURN-OF-NUT METHOD WITH ATTENTION TO LEAVE EQUAL DISTANCE AND EQUAL FORCE ON EACH LEG OF THE U-BOLT. 4.0 TEST 5.0 PACKAGING 5.1 PACKAGING SHALL MEET COMMSCOPE REQUIREMENTS PER DOCUMENT IS-PL-3005. 5.2 PRINTED DOCUMENT TO BE PLACED INSIDE POLYBAG AND THEN IN SHIPPING CONTAINER. 5.3 EXTRA HARDWARE MAYBE SUPPLIED, BAGGED AND SHIPPED. C 2 REV. A REVISIONS DESCRIPTION INITIAL RELEASE 1 DATE YMENG 09OCT23 APPROVED YW1047 40179448CMO D C B A 4 B COMMSCOPE, INC. OF NORTH CAROLINA TOLERANCES 1 PLACE .X[.X] ± 0.2[6.3] 3 PLACE.XXX[.X] ± 0.060[1.5] 2 PLACE .XX[.X] ± 0.12[3.0] ANGLES ± 2° SAP MATERIAL MASTER SFG23RHDXL15-4-126 FINISH MATERIAL UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES INTERPRET PER ANSI Y 14.5M-1994 NAME DATE TITLE CE YMENG RW YMENG 09OCT23 SF,15',(4)2.88"X126"-PIPES-PIM-SPACED 10/18/2023 A DENSITY lbs/in³ MASS 1110.84 lbs VOLUME 3917.43 in³ SURFACE AREA 33664.99 in² AD YW1047 10/18/2023 1:32 SFG23RHDXL15-4-126 RE YMENG 10/18/2023 ECN 40179448CMO SCALE DOCUMENT NO. C 2023 CommScope, Inc. Confidential HEIGHT 126" LENGTH 180" WIDTH 120" SIZE Auth Group INSL MODEL DRAWING SHEET C VERSION 00 STATUS RE REVISION VERSION STATUS A 00 RE REVISION A 1 OF 5 3 2 1 4 D 2 3 1 3 3 13 6 24 ALL GB-05225 BOLTS IN THIS ORIENTATION C 12 3 4 7 9 10 11 14 DETAIL A SCALE 1 : 5 27 COMPONENT PART NUMBERS PROVIDED FOR ASSEMBLY PURPOSES; INDIVIDUAL COMPONENTS MAY BE SHIPPED AS PARTS WITHIN AN INCLUDED KIT. ITEM PART NO. DESCRIPTION QTY. WEIGHT 1 SFG23180-00 ARM, STANDOFF, SFG23 2 120.07 LBS 2 SFG2204 WELDMENT, BACK VERTICAL ARM MOUNT 1 97.29 LBS 3 GB-05225 5/8" X 2-1/4" GALV BOLT KIT B 4 SFG2380 WELDMENT, HD, TOP TAPER BRACKET 14 0.28 LBS 1 22.78 LBS 5 SFG2381 WELDMENT, HD, LOWER TOWER LEG BRACKET 1 17.42 LBS 6 SFG2289 G2 RRU BACK CLAMP, HD 2 18.65 LBS 7 SFG2386 WELDMENT, SFG2 AZIMUTH BRACKET 1 10.69 LBS 8 SFG2397-00 WELDMENT, G23 AZIMUTH BRACKET 1 8.56 LBS 9 MT-382-18 5/8" X 18" THREADED ROD 8 1.43 LBS 10 GWL-05 5/8" GALV LOCK WASHER 16 0.03 LBS 11 GN-05 5/8" GALV HEX NUT 24 0.08 LBS 12 GUB-4355 1/2" X 3-5/8" X 5" GALV U-BOLT 3 0.71 LBS 13 GWF-05 5/8" GALV FLAT WASHER, 1.7OD 2 0.06 LBS 14 GUB-4352 1/2" X 3" X 5-1/4" GALV U-BOLT 10 0.71 LBS 15 SAB01 FORMED CLAMP 4 1.35 LBS 16 MT-379-8 1/2" X 8" GALV THREADED ROD 4 0.45 LBS 17 XAU01 ANGLE, CROSSOVER, 1.9-3.5" X 1.9-3.5" OD 4 2.98 LBS 18 GB-04145 1/2" X 1-1/2" GALV BOLT KIT 2 0.13 LBS 19 GWF-04 1/2" GALV FLAT WASHER 8 0.04 LBS 20 GWL-04 A 21 GN-04 1/2" GALV LOCK WASHER 1/2" GALV HEX NUT 10 0.01 LBS 10 0.04 LBS 22 XP-R CROSSOVER PLATE, ROUND, UP TO 3.5" OD 2 6.20 LBS 23 MT546120120 PIPE, 2.875"OD X 120" 2 35.44 LBS 24 MT546180276 PIPE, 2.875"OD X 180" 2 115.33 LBS 25 SFG23100 LABEL, SFG23RHDXL 1 0.04 LBS 26 XP-2525 CROSSOVER PLATE KIT, 2-7/8 OD X 2-7/8 OD 8 8.37 LBS 27 MT-546-126 PIPE, 2.875"OD X 126" 4 61.05 LBS 4 NOTE NO. 3 2 1 17 18 15 D 16 19 20 21 22 25 1 A C 23 5 8 TOP B ALLOWABLE TIEBACK ANGLE 15 DEGREES VERTICAL 25 DEGREES HORIZONTAL 15 DEGREES BOTTOM 25 DEGREES 15 DEGREES 2 25 DEGREES COMMSCOPE, INC. OF NORTH CAROLINA TITLE SF,15',(4)2.88"X126"-PIPES-PIM-SPACED A SIZE C C 2023 CommScope, Inc. Confidential SCALE 1:16 DOCUMENT NO. SFG23RHDXL15-4-126 VERSION 00 DRAWING STATUS RE REVISION A SHEET 2 OF 5 1 4 C D 23 B 120.0 3048.0 C 25 56.0 1422.4 56.0 1422.4 B A 180.0 4572.0 4 3 2 TIEBACK MUST BE CONNECTED TO A RIGID MEMBER THAT PROVIDES ADEQUATE SUPPORT WITHIN THE LIMITS NOTED IN THE TIEBACK ANGLE RANGE DETAIL. UNLESS APPROVED BY ENGINEER OF RECORD. SPINE STEM OF NEIGHBORING MOUNT IS ACCEPTABLE. 17 14 1 18 15 D 16 19 20 21 61.6 1564.8 56.0 1422.4 FOR POLES UP TO 8.0" IN DIAMETER 23 DETAIL B SCALE 1 : 8 DETAIL C SCALE 1 : 6 ALLOWABLE TIEBACK ANGLE 15 DEGREES VERTICAL 25 DEGREES HORIZONTAL 15 DEGREES FOR POLES UP TO 3.25" IN DIAMETER C 25 DEGREES 25 DEGREES 15 DEGREES TOP D B 126.0 3200.4 33.0 838.2 120.0 3048.0 BOTTOM E COMMSCOPE, INC. OF NORTH CAROLINA TITLE SF,15',(4)2.88"X126"-PIPES-PIM-SPACED A SIZE C C 2023 CommScope, Inc. Confidential SCALE 1:21 DOCUMENT NO. SFG23RHDXL15-4-126 VERSION 00 DRAWING STATUS RE REVISION A SHEET 3 OF 5 3 2 1 4 D 1 3 3 13 6 7 11 12 9 10 11 4 C DETAIL D SCALE 1 : 5 THE THREADED ROD CAN ONLY EXPOSE 4 TO 7 THREADS ON ONE SIDE OF THE BRACKET, WHICH IS TO PREVENT INTERFERENCE WITH THE SIDE BOLTS 2 1 B 3 13 6 8 12 A 11 9 10 11 5 DO NOT OVER TIGHTEN, END OF POLE CAN BE DAMAGED DETAIL E SCALE 1 : 5 4 3 2 1 1 1 D 3 3 7 4 C 12 DETAIL ISO TOP ROTATED VIEW SCALE 1 : 5 B 1 1 3 8 3 5 12 DETAIL ISO BOTTOM ROTATED VIEW SCALE 1 : 5 COMMSCOPE, INC. OF NORTH CAROLINA TITLE SF,15',(4)2.88"X126"-PIPES-PIM-SPACED A SIZE C C 2023 CommScope, Inc. Confidential SCALE 1:21 DOCUMENT NO. SFG23RHDXL15-4-126 VERSION 00 DRAWING STATUS RE REVISION A SHEET 4 OF 5 2 1 4 3 ACCESSORIES ORDERED SEPARATELY: D C B A 4 6 SFG2289 SLOTS ALLOW FOR MOUNTING OF RRU OR OTHER EQUIPMENT 3 2 RR-APEX4 APEX 4 RRU MOUNTING 1 D C B GBSF278 BUSS BAR MOUNT KIT DETAIL N SCALE 2 : 15 COMMSCOPE, INC. OF NORTH CAROLINA TITLE SF,15',(4)2.88"X126"-PIPES-PIM-SPACED A SIZE C C 2023 CommScope, Inc. Confidential SCALE 1:12 DOCUMENT NO. SFG23RHDXL15-4-126 VERSION 00 DRAWING STATUS RE REVISION A SHEET 5 OF 5 2 1