HAM Systems | Home Automation and More
HAM Systems Help Center
User Manual for HAM Systems models including: DIN Rail Wi-Fi Switch, Rail Wi-Fi Switch, DIN Wi-Fi Switch, Wi-Fi Switch, Switch
DIN rail Wi-Fi Switch with Energy metering | HAM DinSwitch
HAM DinSwitchM - WiFi Din Rail Switch with energy metering – HAM Systems
File Info : application/pdf, 2 Pages, 162.74KB
DocumentDocumentTROUBLESHOOTING The Status LED is not lit and the The device does not respond to device is shown as disconnected on manual control via the on/off the app button. This means that the device is not connected to the Cloud Check that the device is powered on If not powered on, cut the power and Check that the device is powered on check your wiring according the If not powered on, cut the power and check diagram in page 1. your wiring according the diagram in page 1. If the device controls a din rail power Power on the device and set it up (page 2). relay, then check that the device is Check your Internet connection. If you correctly interfaced to the rail power cannot access the Internet with a different device on the same Wi-Fi network check with your ISP relay. Try restarting the device. Check that the server is accessible at https://hamsystems.eu with your browser. If it is not, check again in 5 minutes or refresh the app / webpage Try restarting the device with the Restart More information about the installation of our devices, their capabilities and the use of our platform can be found at https://hamsystems.tawk.help/ Button and / or with removing and reattaching the power. Check if the device is connected to your Wi-Fi router / Access Point. If the device does not appear to be connected, then repeat the setup procedure and make sure that the Wi-Fi name and password are correct. The device may also need to be whitelisted depending on your network configuration. Note that the device and the app use the ports This product is in compliance with the Radio Equipment Directive (RED) 2014/53/EU and the Restriction of Hazardous Substances (RoHS) Directive 2011/65/EU and carries the CE Mark. The complete EU declaration of conformity can be found at https://hamsystems.eu/res/doc/dinswitc hm_ce.pdf 9001 and 9002 Manufacturer: Home Automation and More P.C. 76, 28th October, 54642, Thessaloniki, Greece 4 DinSwitchM 1. Line IN 2. N 3. Line OUT 4567 4. CT+ 5. CT- 6. S0+ (Input) - not together with CT 10 8 9 7. S0- (Input) - not together with CT 8. Output LED 11 9.Status LED 10. ON/OFF Button 1 23 11.Restart Button Lout 12. Current Transformer (CT) L 12 N Internet connection via Wi-Fi (2.4 GHz) Remote Control via Android/iOS app or web app Easy setup Output 230VAC,5A max Input 230VAC, <2W 2 years warranty Energy Measurement with Current Transformer or pulse input Measuring Energy, Power, Voltage, Current, Power Factor, Reactive Power when using the CT 1 SETUP The installation must be carried out ONLY by qualified personnel (e.g. electricians) In order to connect the device to your Wi-Fi network, you need to use the HAM Systems app. All the other features are also available on the Web on https://hamsystems.eu 1. Before wiring the device make sure that the power is off! 2.Connect the device according to the wiring diagram on the first page. The device must be installed in an electrical panel where the user does NOT have access. The device is NOT protected against overload or short-circuit conditions. An overload protection device must be used in your electrical panel. 3. Put the Current Transformer around the wire you want to measure. 4. Check your connections and power up the device 5. Open the HAM Systems app. If you don't have an account create one 6. Click on (+) button on the devices list view on the smartphone app 7. Follow the instructions on the app 8.If the Status LED is fully on and the device does not appear on the app, then you may also need claim the device to your account. Click on (+) and select the Claim Device option 9. You should now be able to control the device on the app In case you are having difficulties, you can try restarting the device and repeating the aforementioned steps. If you want to change the Wi-Fi network of your device, you can do so by doing the steps 5-7 . You don't have to re-claim your device in this case SAFETY WARNINGS Incorrect wiring of the device may lead to permanent damage to the device and / or sensors. Make sure your connections are correct before powering the device. Do not disassemble the device! Doing so, voids the warranty. In case of loss of network, you will not be able to monitor the real-time values of the device You should not rely on the device in such a way that puts human or animal lives at risk. You are responsible for checking the accuracy of the readings periodically. The device is designed for installation inside an electrical panel where access is restricted and ONLY done by professionals (e.g. electricians) 2 Do not use the device to control the electrical power of network devices that affect the HAM device's internet connectivity, such as the Wi-Fi router. USAGE To use the device, visit our webapp at https://hamsystems.eu or search HAM Systems at the App Store / Play Store Some features of the app: Control outputs from anywhere in the world via the Internet Measurement of power consumption, active and reactive power, voltage, current, power factor, frequency Set up time based schedules and timers View real time and historical output state. Generate PDF / CSV reports Create If-This-Then-That rules and automations Organize your devices with groups and floor-plans. Device sharing with other users Secured communications with TLS The Setup button is used during the setup process to pair the device to your Wi-Fi network The Restart button restarts the device, similar to power cycling TECHNICAL SPECIFICATIONS Rated Voltage 230 VAC Output 1x 5A / 230VAC (max) Input (for measuring) Via CT (80A/80mA) or via pulse SO Via CT (max 80A): Energy / Power / Current Measurement /Voltage / Power factor / Frequency Via Pulse input: Energy / Power (approximately) Enviromental conditions -10°C to 55°C Dimensions 1 DIN Rail Module, width 17.5mm Enclosure Material ABS UL 94 V-0 Communications Wi-Fi IEEE 802.11 b/g/n 2.4Ghz protocol Bluetooth Low Energy 3