Homepage STEP2 - step2
PRG | People. Production. Possibility.Contact PRGPRG | Proprietary Product Support
User Manual for PRG models including: Series 400 7-Port Ethernet Switch, Series 400, 7-Port Ethernet Switch, Ethernet Switch, Switch
Download PRG Series 400 User Manual PDF
File Info : application/pdf, 14 Pages, 786.37KB
DocumentDocumentWWW.PRG.COM PRG SERIES 400® 7-PORT ETHERNET SWITCH & 10-PORT ETHERNET SWITCH USER MANUAL AutoPar®, Bad Boy®, PRG Series 400®, Mbox Extreme®, V676®, Virtuoso®, Virtuoso® DX, and Virtuoso® DX2, are trademarks of Production Resource Group, LLC, registered in the U.S. and other countries. All other brand names which may be mentioned in this manual are trademarks or registered trademarks of their respective companies. This manual is for informational use only and is subject to change without notice. Please check www.prg.com for the latest version. PRG assumes no responsibility or liability for any claims resulting from errors or inaccuracies that may appear in this manual. PRG Series 400® Ethernet Switch User Manual Version as of: October 18, 2010 PRG part number: 02.9801.0001 B Production Resource Group Dallas Office 8617 Ambassador Row, Suite 120 Dallas, Texas 75247 www.prg.com PRG Series 400® Ethernet Switch User Manual ©2006-2010 Production Resource Group, LLC. All Rights Reserved. INTRODUCTION About This Manual This manual provides necessary information regarding product safety, installation, and operation for the following PRG equipment: + PRG Series 400® 10-Port Ethernet Switch (20.9801.0200) + PRG Series 400® 7-Port Ethernet Switch (20.9801.0200.07) Familiarizing yourself with this information will help you get the most out of your PRG product. WARNING: It is important to read ALL accompanying safety and installation instructions to avoid damage to the product and potential injury to yourself or others. Additional Documentation For more information on related equipment, refer to the following PRG manuals: + PRG Series 400® Power and Data Distribution System User Manual (02.9680.0001.xx) + PRG Series 400® Power and Data Distribution System Service Manual (02.9680.0010) + Virtuoso® Node User Manual (02.9669.0001) + Virtuoso® Node Plus User Manual (02.9801.0301) For more information regarding DMX512 systems, refer to the DMX512/1990 & AMX 192 Standards publication available from United States Institute for Theatre Technology, Inc. (USITT). USITT 6443 Ridings Road Syracuse, NY 13206-1111 USA 1-800-93USITT www.usitt.org For more information regarding Art-Net protocol, refer to the specification for Art-Net II Ethernet Communication Standard available from Artistic Licence Ltd. Artistic Licence (UK) Ltd (Registered Office) 24 Forward Drive, Christchurch Avenue, Harrow, Middlesex, HA3 8NT, United Kingdom +44 (0)20 88 63 45 15 (phone) +44 (0)20 84 26 05 51 (fax) www.artisticlicence.com For additional documentation, please visit our support tech center at: www.prg.com/support PRG SERIES 400® ETHERNET SWITCH USER MANUAL 1 Customer Service For technical assistance, contact the PRG International Service Center or contact your nearest PRG office. Contact information for all PRG office locations can be found on our website at: www.prg.com/about-us/locations/ PRG Dallas (International Service) 8617 Ambassador Row, Suite 120 Dallas, Texas 75247 USA Phone: 214.630.1963 Fax: 214.630.5867 Service Fax: 214.638.2125 Service Email: orders@prg.com For additional resources and documentation, please visit our website at: www.prg.com 2 PRG SERIES 400® ETHERNET SWITCH USER MANUAL OVERVIEW 10-Port Ethernet Switch The PRG Series 400 10-Port Ethernet Switch provides a powerful and convenient interface between V676®, Virtuoso®, or DMX512 control consoles and their control equipment. The 10-Port Ethernet Switch offers two types of connections: isolated copper Ethernet ports and fiber optic ports. The fiber optic ports provide the ability to send fast and reliable information up to 2 kilometers away without the need for repeaters using Virtuoso Fiber Optic Cable. The copper Ethernet connections offer the ability to combine standard copper connections with fiber optic transmissions. Note: Copper connections are limited to a maximum distance of 300 feet. The 10-Port Ethernet Switch automatically determines the speed of each network connection based on the equipment connected to the switch and supports multiple connections with transmission and reception occurring simultaneously. Features: + Seven isolated copper Ethernet ports for input of 10Base-T and 100Base-TX standard signal (Neutrik® EtherCon® connectors). + Three fiber optic Ethernet ports for transmission of 100Base-FX standard signal. Two ports allow use of a Fiber Optic Cable input connector and one port allows use of a Fiber Optic Cable output connector. + Automatic detection and configuration of input signal speed. + Link, Transmission, and Reception status LEDs for all ports. + Neutrik® PowerCon® connector for input AC supply. + DC power status LED. + Standard 1U 19" rack mount chassis. Included Items The following illustration shows all items included with this model: PRG Series 400 10-Port Ethernet Switch (20.9801.0200) AC Line Cord 208V PowerCon® Cable Assembly (25.9801.0214) Figure 1: 10-Port Ethernet Switch Included Items PRG SERIES 400® ETHERNET SWITCH USER MANUAL 3 Controls and Indicators The Series 400 10-Port Ethernet Switch contains the following connections and LED indicators. DC Power Indicator indicates AC power is applied. 10/100 Base T Connections input/output ports for standard signals. Fiber Optic Input - ports for fiber optic cables with input connectors. Fiber Optic Output - port for a fiber optic cable with an output connector. Ethernet LEDs indicates valid Ethernet link, transmit and receive for each connection when lit. Fiber Data LEDs indicates valid Fiber link, transmit and receive for each connection when lit. Figure 2: 10-Port Ethernet Switch Front Panel Neutrik Connector Allows connection of AC Line Cord 208V PowerCon Cable (supplied). Figure 3: 10-Port Ethernet Switch Rear Panel 4 PRG SERIES 400® ETHERNET SWITCH USER MANUAL 7-Port Ethernet Switch The PRG Series 400 7-Port Ethernet Switch provides a powerful and convenient interface between V676®, Virtuoso®, or DMX512 control consoles and their control equipment. The 7-Port Ethernet Switch provides seven isolated copper Ethernet ports. Note: Copper connections are limited to a maximum distance of 300 feet. The 7-Port Ethernet Switch automatically determines the speed of each network connection based on the equipment connected to the switch and supports multiple connections with transmission and reception occurring simultaneously. Features: + Seven isolated copper Ethernet ports for input of 10Base-T and 100Base-TX standard signal (Neutrik® EtherCon® connectors). + Automatic detection and configuration of input signal speed. + Link, Transmission, and Reception status LEDs for all ports. + Neutrik® PowerCon® connector for input AC supply. + DC power status LED. + Standard 1U 19" rack mount chassis. Included Items The following illustration shows all items included with this model: PRG Series 400 7-Port Ethernet Switch (20.9801.0200.07) AC Line Cord 208V PowerCon® Cable Assembly (25.9801.0214) Figure 4: 7-Port Ethernet Switch Included Items PRG SERIES 400® ETHERNET SWITCH USER MANUAL 5 Controls and Indicators The Series 400 7-Port Ethernet Switch contains the following connections and LED indicators. DC Power Indicator indicates AC power is applied. 10/100 Base T Connections input/output ports for standard signals. Ethernet LEDs indicates valid Ethernet link, transmit and receive for each connection when lit. Figure 5: 7-Port Ethernet Switch Front Panel Neutrik Connector Allows connection of AC Line Cord 208V PowerCon Cable (supplied). Figure 6: 7-Port Ethernet Switch Rear Panel 6 PRG SERIES 400® ETHERNET SWITCH USER MANUAL INSTALLATION Installing Ethernet Switch A Series 400 Ethernet Switch can be used independently or installed directly in a Series 400 rack chassis, using any blank space above the LED Meter Module. To install in Series 400 rack: Step 1. Install Ethernet Switch as required in top portion of rack chassis (Figure 7). Step 2. At Ethernet Switch rear panel, connect AC Line Cord 208V PowerCon® Cable (supplied) to Neutrik® connector. Step 3. After power is applied, verify that ON indicator is lit. Step 4. At front panel, connect data cables as required. Refer to "Connecting Ethernet Switch to System" on page 8. SERIES 400 RACK CHASSIS 3U of rack space for adding additional signal processing devices. LED Meter Module EXAMPLE CONFIGURATION S400 Rack Components May Vary Figure 7: Series 400 Rack PRG SERIES 400® ETHERNET SWITCH USER MANUAL 7 Connecting Ethernet Switch to System The Series 400 10-Port Ethernet Switch connects Ethernet devices using both CAT5e copper wire and armored fiber optic cable. Copper wire communication ports conform to 10/100Base-Tx standards and the fiber ports conform to 10/100Base-Fx standards. The Series 400 7-Port Ethernet Switch connects Ethernet devices using only CAT5e copper wire. AC Input SERIES 400 ETHERNET SWITCH 10/100Base-T 10/100Base-T 10/100Base-T 10/100Base-T 10/100Base-T 10/100Base-T 10/100Base-T Fiber Optic Fiber Optic Virtuoso Nodes or Any Ethernet Device (up to 7) Fiber Optic Out to Additional Switches Input from a Virtuoso/V676 Console or another switch Input from a Virtuoso/V676 Console or another switch 10-Port Model Only Figure 8: Device Connection Diagram The following example system diagrams illustrate an Ethernet Switch being used with a Series 400 Power and Data Distribution Rack. FIBER OPTIC CABLE FIBER OPTIC CABLE TO OTHER DEVICES DMX UNIVERSE CABLES TO OTHER SWITCHES PRG S-400 10-PORT ETHERNET SWITCH VIRTUOSO NODE A B VIRTOUSO CONSOLE A A A B B A B CAT5e CABLES VIRTOUSO CONSOLE B SERIES 400 RACK * Fiber optic connections available only with the 10-Port Ethernet Switch model. Figure 9: Sample System Connection Diagram 1 8 PRG SERIES 400® ETHERNET SWITCH USER MANUAL FIBER OPTIC CABLE FROM REMOTE RACKS CAT5e CABLE TO LOCAL RACKS AB FIBER OPTIC CABLE TO REMOTE RACKS PRG S-400 10-PORT ETHERNET SWITCH A B A A B B A B SERIES 400 RACK * Fiber optic connections available only with the 10-Port Ethernet Switch model. Figure 10: Sample System Connection Diagram 2 PRG SERIES 400® ETHERNET SWITCH USER MANUAL 9 SPECIFICATIONS Technical Specifications POWER REQUIREMENT: COOLING: OPERATING TEMP: COPPER PORTS: FIBER OPTIC PORTS: INDICATORS: HOUSING: WEIGHT: COMPLIANCE: 90 to 264 VAC, 47 to 63 Hz Draws less than 60 watts continuously. Convection. -20°C to 50°C (-4°F to 122°F) Seven isolated copper ports that can accept Ethernet signals using either 10Base-T or 100Base-TX standards. Automatic detection and configuration of input signal speed. (10-Port model only) Three fiber optic ports that can accept 100Base-FX Ethernet signal. The speed and direction of these ports are fixed. The ports use 62.5/125um multi-mode fiber media at 1300nm wavelength and operate up to a 2KM distance. Green LED power indicator to show that DC power has been applied. Status LEDs for each port indicating Link, TX Data, and RX Data. Standard 1U 19" rack mount chassis. 4.5 lbs (2.04 kg) United States: ANSI/UL 60950-1-UL Standard for Safety for Information Technology Equipment Safety Canada: CAN/CSA C22.2 No. 60950-1 Information Technology Equipment Safety Europe: CE Mark 1.72" (44 mm) 12" (305 mm) 11" (279 mm) 19" (483 mm) 10-Port Model Shown All models have the same dimensions 10 PRG SERIES 400® ETHERNET SWITCH USER MANUAL PRG Series 400® Ethernet Switch User Manual Version as of: October 18, 2010 PRG part number: 02.9801.0001 B Production Resource Group Dallas Office 8617 Ambassador Row, Suite 120 Dallas, Texas 75247 www.prg.com