Instruction Manual for moooni models including: CFL-1004-03, CFL-1004-03 52 Inch Modern Crystal Ceiling Fan, 52 Inch Modern Crystal Ceiling Fan, Modern Crystal Ceiling Fan, Crystal Ceiling Fan, Ceiling Fan, Fan
Moooni 52 Inch Modern Crystal Ceiling Fan with Lights and Remote, Elegant Chandelier Fan Light KIt Fandelier with 5 Wooden Blades for Bedroom Living Room Silver : Tools & Home Improvement
CFL-1004-03 Installation Manual (PDF) Moooni MECDY 52,Inch,Modern,Crystal,Ceiling,Fan,with,Lights,and,Remote,Elegant,Chandelier,Fan,Light,KIt,Fandelier,with,5,Wooden,Blades,for,Bedroom,Living,Room,Silver,,
9f29f484-f895-4786-b846-48a28599623a Installation Manual (PDF) CROSSIO Glisten Lighting CROSSIO,Crystal,Ceiling,Fan,with,Lights,Modern,Chandelier,Fan,with,Remote,Chrome,Reversible,Fan,Light,Fixture,for,Bedroom,Dining,Room,52",B08GLBWGBX,
Ceiling Fan Model No.: CFL-1004-03 Scan for Installation Video Please contact us with the following information: 1. Screenshot of your order page, including product picture, name, and order ID number. 2. Problem details with pictures / short video if possible. Email: lightingcustomercare@gmail.com Scan for Online Installation Video Note: The remote receiver in the installation video is already assembled in the fan motor housing. The product in the video may be different from this one 1 Packing List A B C X 1 X 16 X 33 D E X 25 X 25 Name Mounting Bracket Canopy Downrod Adapter Cover Fan Motor Fan Blade Blade Arm QTY 1 1 2 1 1 5 5 Name Crystal Shade Remote Controller Hardware Bag Crystal Strand QTY 1 1 1 100 NOTE: 1. The remote receiver in the installation video is already assembled in the fan motor housing. 2. The remote control requires 2 AAA 1.5V batteries (not included). 3. The crystals are fragile, and spare parts are provided. 2 Safety Rules 1. Be sure the power to the wires you are working on is disconnected, either the fuse is removed or the circuit breaker is turned off. Turning the power off using the light switch is not sufficient to prevent electrical shock. 2. A qualified licensed electrician is required for the installation. 3. The outlet box and support structure must be securely mounted and capable of reliably /supporting a minimum of 50 pounds. Use only UL (cUL for Canadian Installation) listed mounting boxes marked "FOR FAN SUPPORT". 4. The fan must be mounted with a minimum of 7 feet clearance from the trailing edge of the blades to the floor. 5. Do not operate reversing switch while fan blades are in motion (if applicable). Fan must be turned off and blades stopped before reversing blade direction. 6. Do not place any objects in the path of the blades. 7. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan. 8. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened soft cloth will be suitable for the cleaning. 9. After marking electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be spread apart with the grounded conductor on one side of the outlet box. 10. Electrical diagrams are reference only, different fan light may have different light shade and bulbs. 11. Use only our replacement parts. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. Warning: To reduce the risk of personal injury, use only the two steel screws and washers provided with the outlet box for mounting to the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and need to be replaced, consult a qualified electrician if in doubt. To reduce the risk of fire, electric shock or person injury, mount fan to outlet box marked "acceptable for fan support". To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades. 3 Installation Preparation Tools You Need Ladder Pliers Wire Strippers Screwdrivers Power Drill (optional) If mounting to a support structure, you will also need the optional tools. Drill Bit (optional) What to Expect with Your Installation 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fanrated outlet box 7 feet from bottom edge of blade to the floor Assess location You may need a friend to help you. Ceiling angles greater than 22° will require an Angled Mounting Kit. Check box to see fan weight Assess ceiling angle Mounting Options Support Structure Short downrod Outlet Box (required) Long downrod Outlet Box (required) Use short downrod for flat and less than 9 feet ceiling. Use long downrod for high or angled ceiling less than 22°. 4 2. Assembling the Fan Blade Fan Motor Fig. 1 Blade Arm 1. Assembling the Blade Arm Step 1. Take off screws from the fan motor. Step 2. Place the blade arms to the motor. Step 3. Attach the arms onto the motor with the screws taken off (Fig. 1). 2. Assembling the Blade Attach fan blade onto the blade arm with screws and plastic washer pro vided (Fig. 2). NOTE: Make sure to assemble the blade arms and blades in sequence and fasten the screws with equal force. Screw Plastic washer Fan Motor Blade Arm Blade Fig. 2 5 3. Installing the Fan NOTE: This ceiling fan is supplied with two types of hanging downrods: 1. The short downrod for "close-to and flat ceiling" installation. It is recommended in rooms with less than 9 feet ceilings or in areas where additional space is desired from the floor to the fan blades. 2. The long downrod is for high ceiling. 3. Angled ceiling is not supported. Outlet box Mounting bracket Hook Power Wire Flat washer Mounting screw (supplied with the outlet box) 1. Installing the Bracket Step 1. Pass the power wires through the center Fig. 3 hole in the mounting bracket as shown in Fig. 3. Step 2. Secure the mounting bracket to the ceiling outlet box with the screws and washers provided with your outlet box. Downrod 2. Assembling the Fan Adapter cover Step 1. Assemble the canopy and adapter cover as Fig. 4. Step 2. Remove the the bolt, pin and set screws Bolt from the top of the fan motor assembly. Step 3. Route wires from the top of the fan motor through downrod/ ball. Fig. 4 Step 4. Align the holes at the bottom of the downrod with the holes in the collar on top of the motor housing (Fig. 4). Carefully insert the bolt through the holes in the collar and downrod. Be careful not to jam the bolt against the wires inside the downrod. Insert the pin to the end of the bolt (Fig. 4). Step 5. Fix the downrod with set screws provided. Fig. 2 Canopy Set screw Pin 3. Hanging the Fan Place the downrod ball into the bracket socket (Fig. 5). Be sure the fixation slot is locked by the bracket. Fixation slot Fig. 5 6 4. Wiring Fig. 6 NOTE: THIS FAN ONLY NEEDS ONE SET OF INPUT WIRES (black, white and ground wire). Both of the fan and lights will be controlled by the remote controller. The wall switch is not able to control the fixture full functionally. THIS FAN CAN ONLY BE CONNECTED ONTO ON/OFF SWITCH IF YOU HAVE ONE, NOT SUITABLE FOR DIMMAER SWITCH. Step 1. Connect the wires from the fixture to supply wires, black wire to the live wire, white wire to neutral wire, yellow & green / green / bare copper wire to ground wire. Step 2. After connecting the wires, spread them apart so that the live wires are on one side of the outlet box and the neutral wires are on the other side. 5. Attaching the Canopy Outlet box Mounting bracket Screw Screw Step 1: Insert wires and connectors into the outlet box. Step 2: Slide canopy up to the ceiling, and attach it to the mounting bracket using the screws provided. Ensure all screws are tightly secured. Canopy Fig. 9 7 6. Installing Bulb and Light Shade E D C B A 1. Connect the shade wires to the motor wires, matching black/blue to black/blue and white to white. 2. Securely attach the crystal shade to the motor using the screws provided. 3. Attach the crystal strand to the shade frame as follows: #D and #E for the upper layer alternately, #C for the middle layer, #B for the outer ring of the lower layer, and #A for the middle of the lower layer. 4. Install three light bulbs (E12, max 40W each, LED recommended). 8 Remote Control Instructions NOTE: Please insert 2 batteries before using. AAA 1.5V battery x 2pcs (not included) : Turn off the fan and lights. : "F" refers forward fan direction."R" refers reverse the fan. : 1/2/3/4/5/6 for fan speeds. : 1H/2H/4H for timing the fan. : Turn on/off the lights. : Natural wind of the fan, fan speed will change automatically when using this function. : Turn off the fan. REMOTE SIGNAL PAIRING: If the remote control loses the signal of the fan, turn off the power from wall switch, then turn it on, press immediately for around 3 seconds, after the fixture beeps or flashes, then it's down. 9 Troubleshooting 1. Fan doesn't work · Check the wall switch to ensure it is an ON/OFF switch, not a dimmer switch. · Check the remote control battery (not included). · Check the circuit breaker to ensure power is on. · Turn off power from the circuit breaker, then loosen the canopy and check all connections according to the wiring diagram. 2. Bulbs don't light up/flicker/noisy operation · Check that the fixture is connected to an ON/OFF wall switch, not a dimmer switch. · Verify that the power and switch are on. · Check the bulb to ensure it is installed correctly. · Replace with a new bulb. 3. Noisy operation · Tighten the light fitting. · Re-tighten all screws on bracket, downrod, and fan blades (do not overtighten). · Check if any of the blades are cracked, if so, replace all of them. 4. Excessive wobbling · Tighten all blade screws. · Assemble the blade arms and blades in sequence and fasten the screws with equal force. · Turn off the power, support the fan carefully, and check that the hanger ball is properly seated. · Use the provided balancing kit and instructions (in the hardware bag) to balance the fan. 5. Remote doesn't work · Make sure the battery is installed correctly. · Pair the remote control again (See page 9). · Install 2 new batteries. 10 Clean And Care To clean, wipe fixture with soft cloth. Spray from chemical cleaners can discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture. Ordering Parts Keep this manual for future reference, and in case replacement parts are needed. Available parts can be ordered from place of purchase. Use exact wording from diagrams when ordering parts. 11Adobe Illustrator CC 22.0 (Macintosh) Mac OS X 10.13.3 Quartz PDFContext