ViewSonic VB-MIC-201 USB Expansion Microphone
Quick Start Guide
Contents
- Microphone x 1 (Operating Temperature: -10°C ~ 40°C / 14°F ~ 104°F)
- USB cable x 1
- QSG x 1
Installation
Step A: Connection
Connect the included USB cable to the VB-MIC-201 microphone and then to a USB port on your computer or conference system. The diagram shows a USB 2.0 connection.
Step B: Placement
Place the VB-MIC-201 microphone on a flat, stable surface. The diagram shows the microphone being placed on a table.
Step C: Room Setup
For optimal audio capture in a conference room, position the VB-MIC-201 microphones around the table. The diagram illustrates a typical conference room setup with multiple microphones placed at intervals around a table.
Compliance Information
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and CE General Product Safety Directive 2001/95/EC.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose of the equipment, including any spent or discarded batteries or accumulators, as unsorted municipal waste, but to use the return and collection systems available.
If the batteries, accumulators, and button cells included with this equipment display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0.0005% Mercury, or more than 0.002% Cadmium, or more than 0.004% Lead.
Recycling Instructions: For EU member states, this equipment is compliant with the WEEE directive. Do not dispose of this equipment or its batteries as unsorted municipal waste. Utilize available return and collection systems. The product and its accessories are recyclable. Return to stores or collection points, or dispose of at recycling centers. Prioritize repair or donation of your device.
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:
Substance Concentration Limits
| Substance | Proposed Maximum Concentration | Actual Concentration |
|---|---|---|
| Lead (Pb) | 0.1% | < 0.1% |
| Mercury (Hg) | 0.1% | < 0.1% |
| Cadmium (Cd) | 0.01% | < 0.01% |
| Hexavalent Chromium (Cr6+) | 0.1% | < 0.1% |
| Polybrominated biphenyls (PBB) | 0.1% | < 0.1% |
| Polybrominated diphenyl ethers (PBDE) | 0.1% | < 0.1% |
| Bis(2-ethylhexyl) phthalate (DEHP) | 0.1% | < 0.1% |
| Butyl benzyl phthalate (BBP) | 0.1% | < 0.1% |
| Dibutyl phthalate (DBP) | 0.1% | < 0.1% |
| Diisobutyl phthalate (DIBP) | 0.1% | < 0.1% |
Exempted Components under RoHS2 Annex III
- Copper alloy containing up to 4% lead by weight.
- Lead in high melting temperature type solders (i.e., lead-based alloys containing 85% or more lead by weight).
- Electrical and electronic components containing lead in glass or ceramic, other than dielectric ceramic in capacitors (e.g., piezoelectronic devices) or in a glass or ceramic matrix compound.
- Lead in dielectric ceramic in capacitors for a rated voltage of 125V AC or 250V DC or higher.
Support and Information
For more information, visit the Support Center at www.viewsonic.com.
