Instruction Manual for Dongguan Farui Electronics models including: F11A, 2A2AQ-F11A, 2A2AQF11A, F11A Wifi Printing Camera, Wifi Printing Camera, Printing Camera
Dongguan farui Electronics Co., Ltd F11A WiFi printing camera 2A2AQ-F11A 2A2AQF11A f11a
wifi printing camera (instruction manual) 12 13 1 7 2 3 4 Before using the product, please read the instruction manual carefully. It contains important information, please keep it safe for use. Insert the memory card chip face up directly one. Key function description: 1. Photo/Video mode switch 2. Delete 3. Return/Main menu 4. Power on/off, main menu 5. Photo/video, confirm key 6. Turn up 7. Turn left/photograph 8. Turn right/album 9. Turn down 10. Print on/off 11. Display 12. Microphone 13. Camera 14. Speaker 15. Paper compartment door 16. Lanyard 17. Memory card slot 18. Charging port two. How to replace the printing paper: Photo paper ripped in zigzag direction Lift the two paper clips to open the cover of the paper Load the sticker paper as shown Load thermal paper as shown Turn the hat 180 degrees clockwise to switch the front Camera (Note: The hat only supports rotation 180Degree, please avoid excessive force) Three. Operation illustrate .(4.Camera On/Off switch, Main menu): Long press this button for 3 seconds to turn on and off the camera, and short press to return to the main menu. .(1. Photo /Video mode switch): Select this button to switch the corresponding function and then press (5.Shutter button, Verify) to operate. .(10.Print On/Off switch): To print the photo, please turn on this print switch first .( 13.Lens of camera): It can be manually rotated to switch between front and rear. four. TF card installation and notes: 1. Insert the TF card into the card slot in the correct direction until the TF card is fixed in the card slot. When removing the TF card, press down the TF card gently and wait for the TF card to pop out , then you can remove it(TF card must use a C10 or higher high-speed card. Please do not insert or remove the TF card while the machine is working to avoid damage to the machine and memory card) 2. Please pay attention to the direction of TF card insertion. If it is inserted upside down, this may damage the machine, TF card and card slot. 3.After you inserting the TF card into the machine, the machine will set the TF card as the default storage device. The data in the original TF card may not be readable. Please make a backup of the data first. 4. If the TF card is not compatible with the machine, please use the format option in the internal memory menu to format the TF card or try another TF card. Five. Operating parameters 1. Operating voltage: 7.4V. 2. Operating current: 150mA. 3. Printing operating current: 2A. 4. Charging current: 2A. 5. Charging voltage: 5V. Six. Charging instructions: 1. During charging, the indicator light is always on and indicator light is off when fully charged. 2. When input over-voltage, output under-voltage and over-voltage, output short-circuit or chip over-temperature, and indication of battery connection, etc., the indicator flashes at a frequency of 1.3HZ. 3. It takes 70-130 minutes to fully charge the battery. Seven. Battery use and safety precautions This machine uses a built-in 7.4V / 1200mAh polymer battery. It cannot be removed or replaced. If it is damaged, please contact the seller for repair. The battery must be recharged under adult supervision. When the battery is charging, the toy switch should be turned off. The power terminals must not be shorted. Do not connect more than the recommended number or higher than the recommended voltage (recommended adapter specifications: DC5V2000mA). During the use of the toy, the wire plug housing and other parts should be regularly inspected for damage. If damage is found, stop using it until it is repaired. When the toy is not used for a long time, please fully charge the battery before turning off the power switch. eight. Maintenance method: The electrical components of this product mustn't be exposed to water or placed in a humid environment. When cleaning, wipe the surface stains with a dry cloth. Do not allow children to play with disintegrated, broken, deformed toys to avoid accidents such as accidental swallowing and suffocation. caveat: 1. This product contains small parts, there is a danger of suffocation, not suitable for children under 3 years old. 2. Do not immerse the battery in water, pay attention to moisture and explosion. 3. Do not get close to the fire source when playing. 4. Do not disassemble or modify the battery without authorization. 5. This product needs to be used under direct adult supervision. 6. Toys are not allowed for children under 3 years of age 7. Toys can only use the recommended transformer. 8. Transformers are not toys. 9. There is important information on the package, which must be retained. Nine. Camera specification Dimensions 130x104.2x48.8mm Display 2.4 inch color screen Battery specification 7.4V/1200mAh lithium battery Photo paper specification 57X27mm glossy Number of pixels 240 (RGB)*320 Photo resolution 3280*1848, 4000*2248, 4032*2880 Video resolution 1280*720, 1920*1080 Music format MP3, WAV, WMA, FLAC, APE Maximum support 32G Speaker 8 1W Function WIFI camera video print System language Chinese, traditional Chinese, English, etc. Transmission interface MICRO 5PIN USB2.0 Support system WINDOWS XP/7/8 Body weight 220g Working temperature -5 to 40 Warranty Card Poduct Model_____________S/N:_____________________ Dealer______________ Purchase Date______________ Dealer Seal____________________________________ Replacement / Replacement / Replacement / Repair Date repair records repair unit (seal) WiFi operating instructions Scan code to download APP Scan the QR code on the right with your mobile phone Select the corresponding APP to download: FR_PRINT IOS.............................................iPhoneAPP Android).........................Android phoneAPP 2 3 1 Note: If replacing service, it must be indicated in the "replacement / repair records"; The warranty card must be presented at the same time as the official purchase invoice with the dealer seal, this card is valid. Please be careful and fill in the details of the warranty card. If any alterations are made, this card is invalid. 1. Click the menu button to turn onWIFI 2. Mobile phone selects the machine WIFI name: FR_PR**** 3. Enter the password "12345678" to connect For APP operation details, please check in APP Help Center 90*68mm This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment The devices has been evaluated to meet general RF exposure requirement the device can be used in portable exposure condition without restrictionCorel PDF Engine Version 14.0.0.701 CorelDRAW