Woodpeckers DP-PRO TCS Drill Press Table Extension Wings Owner's Manual
Product Overview
This manual provides instructions for the Woodpeckers DP-PRO TCS Drill Press Table Extension Wings.
The DP-PRO Drill Press Table and DP-PRO Drawer are sold separately at woodpeck.com.
For missing parts or assistance, email mailroom@woodpeck.com or call 800-752-0725 (9:00 a.m. - 4:00 p.m. EST Monday - Friday).
Scan the QR code or visit woodpeck.com under the video tab for installation videos.
Parts List
| Diagram Number | Quantity | Part Name |
|---|---|---|
| 1 | 2 | Table Extension Wing |
| 2 | 4 | Shaft Bracket |
| 3 | 2 | Stainless Steel Shaft (2 Hole) |
| 4 | 2 | Stainless Steel Shaft (1 Hole) |
Hardware Bag
| Identifier | Quantity | Part Name |
|---|---|---|
| A-1 | 6 | Threaded Stud |
| A-2 | 12 | 1/4-20 Hex Nut |
| A-3 | 16 | #10 Pan Head Phillips Wood Screw |
| A-4 | 8 | Shaft Grommet |
| A-5 | 4 | Retaining Snap Ring |
| A-6 | 1 | 1/8" Allen Key |
Assembly Instructions
I. Assembling Brackets for Side Extensions
At this point you will need:
- Shaft Bracket (②) - 4
- Shaft Grommet (A-4) - 8
- #10 Pan Head Phillips Wood Screw (A-3) - 16
- Squeeze the Shaft Grommets (A-4) to collapse them, then insert them into each end of the Shaft Bracket (②) side holes. Repeat for all four Shaft Brackets. (See Figures A/A-1).
- Locate the mounting holes on the underside of the DP-PRO Table. Screw down the four Shaft Brackets (②) to the DP-PRO Table using the sixteen A-3 Pan Head Phillips Wood Screws. (See Figure B). DO NOT OVER TIGHTEN SCREWS.
II. Assembling the Stainless Steel Shafts to Brackets
At this point you will need:
- Stainless Steel Shaft (2 Hole) (③) - 2
- Stainless Steel Shaft (1 Hole) (④) - 2
- Retaining Snap Ring (A-5) - 4
- Slide the two Stainless Steel Shafts (2 holes) (③) through the front Shaft Bracket holes. Ensure the holes on the shafts face outward from the DP-PRO Table, and the grooves on the shaft ends are toward the middle of the DP-PRO Table. (See Figure C).
- Slide the two Stainless Steel Shafts (1 hole) (④) through the rear Shaft Bracket holes. Ensure the holes on the shafts face outward from the DP-PRO Table, and the grooves on the shaft ends are toward the middle of the DP-PRO Table. (See Figure D).
- Snap the four Retaining Snap Rings (A-5) onto the grooved ends of the Stainless Steel Shafts. (See Figures D / D-1).
III. Assembling Threaded Studs to Side Extensions
At this point you will need:
- Table Extension (①) - 2
- Threaded Stud (A-1) - 6
- 1/8" Allen Key (A-6) - 1
- Screw the six Threaded Studs (A-1) into the Table Extensions (①). Note that one side uses the first set of holes (A), and the other side uses the second set of holes (B). (See Figure E).
- Thread the Threaded Studs into the holes on the Table Extensions using the Allen Wrench (A-6). Do not install the Threaded Studs too deep; thread them to approximately 1-1/8". (See Figure E-1).
IV. Assembling Side Extensions to Shafts
At this point you will need:
- 1/4-20 Hex Nut (A-2) - 12
- Install a Hex Nut (A-2) onto a Threaded Stud (A-1). Thread them down to the bottom of the Threaded Stud, just touching the black surface of the Table Extension. DO NOT TIGHTEN THEM. (See Figure F).
- Raise the DP-PRO Table and slide the Table Extension, with the Threaded Studs, into the correct Stainless Steel Shaft holes. The Table Extension will fit flush with the back end of the Table. When the Table Extension is next to the Table, you will see which Threaded Studs align with the holes in the Stainless Steel Shaft. (See Figure F).
- Install another Hex Nut (A-2) onto the Threaded Studs until it stops against the Stainless Steel Shaft, finger-tight. (See Figure G).
- Turn the bottom Hex Nut counter-clockwise until it stops against the Stainless Steel Shaft, finger-tight. (See Figure G-1).
Note: After the Drawer Base is installed and the Table is turned right-side up, the Table Extensions can be checked to see if they are coplanar with the Table. Adjustments can be made by loosening and tightening these hex nuts.
Company Information and Warnings
Woodpeckers, LLC, Strongsville, Ohio. Visit woodpeck.com.
© 2023 Woodpeckers, LLC.
At Woodpeckers, we are constantly reviewing and improving our tools. The most current version of our instruction manuals are always available to download at woodpeck.com (located in the bottom section of the tool's page under the “Additional Information” or “Instructions” tabs).
Stay Connected:
- eClub: Be the first to know about new products, OneTIME Tools & sales by subscribing to our eClub (top center of woodpeck.com).
- YouTube: Subscribe to our YouTube channel for tool tips & tricks.
- Social Media: Interact with us on Facebook, Instagram & TikTok!
- Woodworking Resource Center/Blog: Enjoy shop tips, project ideas, tool techniques & more at the bottom center of woodpeck.com.
WARNING! This product can expose you to chemicals, including chromium, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
WARNING! To reduce the risk of injury, keep hands away from moving parts. Refer to your drill press manual for proper setup and use.
WARNING! To reduce the risk of injury, wear safety goggles or glasses with side shields, ear protection & a dust mask.
