Seasons Sentry 3.04 M / 10 FT Solar LED Cantilever Umbrella with Base

Assembly, Care & Use Manual

Product Information

Model: # UMB-955258

ITM. / ART.: 2127235, 2127232, 2127233, 667334, 1602574

Brand: Seasons Sentry by ATLeisure

Preparation

Before beginning product assembly, completely inspect the umbrella and verify all hardware parts are present. Lay out all hardware contents on a clean, flat surface. Compare the parts with the package contents list and diagrams. If there is damage or any missing parts, do not assemble the umbrella, fill bases with sand/water, or return to the place of purchase. Contact ATLeisure customer service toll free at 1-855-880-7205 (English) or 1-888-692-1033 (French) for replacement parts or further instructions.

Estimated Assembly Time: 40 minutes

Tools Required for Assembly: Open-end wrench or adjustable wrench (not included)

Hardware and Package Contents

Hardware Contents

Part	Picture	Description	Quantity
GG	[Bolt]	Outer Hex Bolt M10-1.5x20 A2-70	4
HH	[Washer]	Flat Washer M10 A2-70	4
JJ	[Bolt]	Inner Hex Bolt M8 A2-70	2
KK	[Wrench]	Inner Hexagon Wrench M8	1

Package Contents

Part	Description	Quantity
A	Blow Molded Base Outside	2
B	Blow Molded Base Inside	2
C	Lower Cross Leg	1
CAN	Canopy (on the umbrella frame)	1
D	Upper Cross Leg	1
E	360° Crank Handle	1
E2	Canopy Crank Handle	1
E3	Canopy Glide Handle	1
F	Holder Pole	1
G	Battery	2
G1	Power Supply	1
K	Pole Sleeve Collar	1
L	Pole Support Cap	1
M	Blow Molded Base Cap	4
N	Umbrella Frame (with canopy)	1
N1	Solar Panel	1

Assembly Instructions

CAUTION: Do not use sharp tools or equipment such as a knife or scissors when removing the protective material, as it may damage the product. Be careful not to throw away small parts such as bolts, washers, etc. that may be wrapped in the protective materials.

Step 1: Place lower cross leg (C) on ground, line up notches and place upper cross leg (D) over lower cross leg (C).

Step 2: Attach holder pole (F) to base by using bolts (GG) and washers (HH) (found in blister pack). Be careful not to over tighten. Adjust holder pole (F) to be sure it is positioned correctly on base. Finally, tighten with adjustable wrench or open-end wrench (not included).

WARNING: Before opening umbrella, complete assembly as instructed in manual. Fill each section of base with sand. Add WATER to wet the sand and continue to fill each section with water up to top. Cover hole with cap. It is recommended at least 91 kg (200 lbs) of weight be placed on cross legs to ensure stability. Failure to do so will result in a weight imbalance and cause umbrella to tip, causing damage and/or personal injury.

Step 3: Fill each base (A & B) with sand, cover with cap (M). Place pole support cup (L) onto holder pole (F) and lay on top of blow molded base (B).

Step 4: Insert plug into socket under solar panel as shown.

Step 5: Put solar panel on top of umbrella and hide the plug and wire inside the cavity at top. Then turn the solar panel clockwise. Do not over tighten.

Step 6: Remove battery (G) from accessories kit and place into the housing located on the arm of the glide handle. Then put the solar umbrella in direct sunlight outdoors to charge the solar panel for 8 hours before the first use. MAKE SURE THE LED LIGHTS ARE OFF ON UMBRELLA TO ALLOW SOLAR PANEL TO FULLY CHARGE BATTERY.

CAUTION: An additional person is suggested to assist with inserting the umbrella into the pole holder.

Step 7: Insert Umbrella Frame with Canopy (N) onto Holder Pole (F). At the same time, slide holder pole collar onto holder pole. Tighten two Hex Bolts (JJ) into holder pole to secure the umbrella using the hexagon wrench (KK). Attach canopy crank handle (E2) onto canopy glide handle (E3) and 360° crank handle (E) to pole.

Operation Instructions

Step 1: Unfasten storage straps around canopy and pole.

Step 2: To open umbrella, squeeze grip on canopy glide handle (E3) and slide up or down on the pole to achieve desired canopy angle. Release grip to lock umbrella canopy frame into place. To open canopy, turn crank handle (E2) clockwise until canopy is fully open as pictured. Central hub light underneath canopy should be flush against the center pole.

Step 3: The canopy can be rotated 360°. To rotate umbrella, insert crank handle (E) onto holder pole (F) and turn the crank handle to the desired position.

Step 4: To close umbrella, turn canopy crank handle (E2) counter-clockwise until canopy is fully closed. Squeeze grip on canopy glide handle (E3) and slide it down pole; release grip to lock it in place. Canopy frame should be vertically upright. Fasten storage straps around canopy and pole.

Step 5: To rotate canopy left and right, pull on handle unlocking mechanism and turn to desired angle. Then, put handle back in locked position to secure.

Lighting Operation & Battery Replacement

CAUTION: YOU MUST CHARGE THE BATTERY BEFORE FIRST USE. Please note that battery can lose charge if left unused or uncharged for a long period of time. Failure to charge the battery will result in premature dimming of the lights in your new solar umbrella. Make sure the light switch is in the off position when charging the solar panel. For everyday normal use, turn light switch on at night when you want to use solar light and turn off switch after use. MAKE SURE LIGHT SWITCH IS IN OFF POSITION DURING DAYTIME TO ALLOW THE SOLAR PANEL TO CHARGE BATTERY.

Step 2: Press light button to turn solar lights on and off. Press once to turn on rib lights on and off. Press a second time to turn on hub light. Press a third time to turn on both ribs and hub lights. Press a fourth time to turn off all lights. Umbrella is equipped with 2 batteries. Remove battery from hub when the battery has drained. Replace battery once fully charged. When solar energy is insufficient, you can use the power supply indoors to charge the battery. Charge level can be seen on battery power meter lights.

INFORMATION: Battery is meant to be charged indoors. Leaving battery outside in inclement weather will damage battery and power supply.

Battery charged after 3-4 hours using power supply or 6-8 hours of direct sunlight. Battery life 6-8 hours when fully charged. Power supply is for indoor use only. Do not use outdoors.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Battery Disposal

Battery should be recycled or disposed of as per state and local guidelines.
Do not open battery or try to replace battery by yourself.
Do not dispose of batteries in fire.
Keep battery (batteries) out of reach of children

Care and Maintenance

See the enclosed Sunbrella® care and cleaning label sewn into interior side of canopy.

Warning and Cautions

DANGER: Keep children out of the assembly area during assembly.
WARNING: Read all instructions before beginning and follow the steps outlined. Failure to assemble and install as instructed could result in the umbrella tipping over causing personal injury and/or property damage.
WARNING: Do not open umbrella in windy conditions, as it could be blown over and cause personal injury or damage. To secure umbrella properly, either bolt it directly to your deck or patio, or use a properly weighted umbrella base. Keep umbrella away from glass tabletops during windy conditions to prevent breakage. Warranty does not cover damage due to neglect, abuse or poor weather conditions.
WARNING: Use only the original power adapter (G1) to charge battery or other power supply with the same voltage. The use of any other adapter or power supply with higher voltage will damage the battery. Original power adapter (G1) uses DC barrel connector size: 5.5x2.5x10mm.
CAUTION: Assemble and use umbrella on flat ground.
CAUTION: Place the base in the desired location for use before filling. Once the base is full, it will be harder to move
CAUTION: Before opening umbrella, insert the plug into the socket under the solar panel. Put the solar panel at the top of umbrella and hide the plug and wire inside the groove at the top of the umbrella. Then turn the solar panel clockwise. Do not over tighten.
INFORMATION: Be sure to secure and/or weight the base of the umbrella.
INFORMATION: Close the umbrella and use the canopy storage straps when umbrella is not in use. If the umbrella is stored off season in a box, the solar panel and battery pack must be removed to avoid damage.
INFORMATION: Schematics in this manual are for assembly and operation illustration only. They may differ from the umbrella's actual appearance.
INFORMATION: It is suggested that the consumer use a cover (not included) to protect umbrella against the elements.

Warranty

This product is covered under a manufacturer's 2-year warranty from date of purchase against defects in materials and workmanship. This warranty does not cover damage due to neglect, abuse or weather related damage. For full warranty disclosure, email us at customerservice@atleisure.com, call toll free at 1-855-880-7205 (English) or 1-888-692-1033 (French) or send mail to:

Atleisure, LLC
Customer Service Dept.
1040 Boulevard SE Ste. B
Atlanta GA 30312.

NOT COVERED UNDER WARRANTY

This warranty excludes the following: acts of nature (i.e. wind, fire or freezing); damage caused by improper assembly, accident, disaster, misuse, abuse, or negligence and discoloration or fading of the finish as a result of exposure to the elements. Product not intended for commercial use. This warranty gives you specific rights, and you may also have other rights which may vary from state to state.

AUSTRALIA:

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Filing a Claim

If you are within your warranty, you may file a claim by sending your receipt and pictures of your damaged umbrella and send to ATLeisure at:

customerservice@atleisure.com

or by mail to:

ATLeisure, LLC
Customer Service Dept.
1040 Boulevard SE Ste. B
Atlanta GA 30312

Made in China

Replacement Parts

Only the individual replacement parts listed below are available while supplies last. Refer to part number(s) and contact our customer service department toll free at 1-855-880-7205 (English) or 1-888-692-1033 (French) 8:00am to 5:00pm EST (Monday - Friday).

Part	Description	Quantity	Re-order No.
A	Blow Molded Base Outside	2	BSE-ABMP-11-BWN-T-C2
B	Blow Molded Base Inside	2	BSE-BBMP-11-BWN-T-C2
C	Lower Cross Leg	1	CSL-C78RX-BWN-T-C2
CAN	Canopy (Indigo, Mushroom, Pebble, Taupe, Dove)	1	CAN-100SQ8RBS-T-IN2-C2 CAN-100SQ8RBS-T-MU2-C2 CAN-100SQ8RBS-T-PEB-C2 CAN-100SQ8RBS-T-T2-C2 CAN-100SQ8RBS-T-DOVE-C2
D	Upper Cross Leg	1	CSL-D78RX-BWN-T-C2
E	360° Crank Handle	1	CRK-E78RHP-BWN-T-C2
E2	Canopy Crank Handle	1	CRK-E78RHP-BWN-T-C2
E3	Canopy Glide Handle	1	CRK-778RG-BWN-T-NS-C2
F	Holder Pole	1	HDP-F78RX-BWN-T-C2
G	Battery	2	SOL-G-RBP-11-T-C2
G1	Power Supply	1	SOL-G1-CC-11-T-C2
K	Pole Sleeve Collar	1	HDP-SLV-F78RX-BWN-T-C2
L	Pole Support Cap	1	PSC-L78R-BWN-T-C2
M	Blow Molded Base Cap	4	BSE-CAP-11-BWN-T-C2
N1	Solar Panel	1	SOL-P11-T-C2
GG	Outer Hex Bolt M10-1.5x20 A2-70	4	HDW-GG-10-T
HH	Flat Washer M10 A2-70	4	HDW-HH-10-T
JJ	Inner Hex Bolt M8 A2-70	2	HDW-JJ-10-T

U.S. Patent No. 8,104,492, U.S. Patent No. 6,612,713, U.S. Patent No. 7,753,546, U.S. Patent No. 8,069,868, U.S. Patent No. 8,375,966, U.S. Patent No. 8,727,555, U.S. Patent No. 8,794,781