Installation Guide for MEAN WELL models including: LPF-16-12, LPF-16-15, LPF-16-20, LPF-16-24, LPF-16-30, LPF-16-12 Constant Voltage Constant Current LED Driver, LPF-16-12, Constant Voltage Constant Current LED Driver, Voltage Constant Current LED Driver, Constant Current LED Driver, Current LED Driver, LED Driver, Driver
File Info : application/pdf, 6 Pages, 502.59KB
DocumentDocument16W Constant Voltage + Constant Current LED Driver
LPF-16 series
User's Manual
IP30
P
File Name:LPF-16-SPEC 2024-10-16
16W Constant Voltage + Constant Current LED Driver
LPF-16 series
SPECIFICATION
MODEL
LPF-16-12 LPF-16-15 LPF-16-20 LPF-16-24 LPF-16-30
OUTPUT
DC VOLTAGE
12V
15V
20V
24V
CONSTANT CURRENT REGION Note.2 6.6 ~12V 8.25 ~ 15V 11 ~ 20V 13.2 ~ 24V
RATED CURRENT
1.34A
1.07A
0.8A
0.67A
RATED POWER
Note.5 16.08W
16.05W
16W
16.08W
RIPPLE & NOISE (max.) Note.3 150mVp-p 150mVp-p 150mVp-p 150mVp-p
VOLTAGE TOLERANCE Note.4 ±4.0%
±4.0%
±4.0%
±4.0%
LINE REGULATION
±0.5%
±0.5%
±0.5%
±0.5%
LOAD REGULATION
±2.0%
±1.5%
±1.0%
±0.5%
SETUP, RISE TIME Note.6 1500ms, 80ms / 115VAC 500ms, 80ms / 230VAC
HOLD UP TIME (Typ.)
16ms/230VAC 16ms /115VAC
30V 16.5 ~ 30V 0.54A 16.2W 200mVp-p ±4.0% ±0.5% ±0.5%
VOLTAGE RANGE
90 ~ 305VAC 127 ~ 431VDC Note.5 (Please refer to "STATIC CHARACTERISTIC" section)
FREQUENCY RANGE POWER FACTOR
47 ~ 63Hz
PF0.97/115VAC, PF0.95/230VAC, PF0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
LPF-16-36
36V 19.8 ~ 36V 0.45A 16.2W 250mVp-p ±4.0% ±0.5% ±0.5%
LPF-16-42
42V 23.1 ~ 42V 0.39A 16.38W 250mVp-p ±4.0% ±0.5% ±0.5%
LPF-16-48
48V 26.4 ~ 48V 0.34A 16.32W 250mVp-p ±4.0% ±0.5% ±0.5%
LPF-16-54
54V 29.7 ~ 54V 0.3A 16.2W 350mVp-p ±4.0% ±0.5% ±0.5%
TOTAL HARMONIC DISTORTION
THD< 20%(@load60%/115VC,230VAC; @load75%/277VAC) (Please refer to "TOTAL HARMONIC DISTORTION(THD)" section)
INPUT
EFFICIENCY (Typ.)
84%
84%
86%
86%
86%
86%
86%
86%
86%
AC CURRENT
0.4A / 115VAC 0.25A / 230VAC 0.2A/277VAC
INRUSH CURRENT(Typ.)
COLD START 45A(twidth=200s measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER
14 units (circuit breaker of type B) / 24 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.75mA / 240VAC
OVER CURRENT
SHORT CIRCUIT PROTECTION
OVER VOLTAGE
OVER TEMPERATURE WORKING TEMP. MAX. CASE TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT
95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed 15 ~ 18V 17.5 ~ 21V 23 ~ 27V 28 ~ 35V 34 ~ 40V 41 ~ 49V Shut down and latch off o/p voltage, re-power on to recover Shut down o/p voltage, recovers automatically after temperature goes down Tcase=-35 ~ +70 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section) Tcase=+70 20 ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH ±0.03%/ (0 ~ 50)
46 ~ 54V
54 ~ 63V
59 ~ 66V
VIBRATION
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS Note.8
UL8750, CSA C22.2 No. 250.0-08; ENEC BS EN/EN61347-1, BS EN/EN61347-2-13 independent, BS EN/EN62384,J61347-1, J61347-2-13,EAC TP TC 004,GB19510.1,GB19510.14 approved,IP67 (optional) ; Design refer to UL60950-1
SAFETY & EMC
WITHSTAND VOLTAGE ISOLATION RESISTANCE
EMC EMISSION Note.8
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25/ 70% RH Compliance to BS EN/EN55015,BS EN/EN61000-3-2 Class C (@load50%) ; BS EN/EN61000-3-3,GB/T 17743 , GB17625.1, EAC TP TC 020
OTHERS NOTE
EMC IMMUNITY MTBF
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity Line-Line 2KV),EAC TP TC 020 3572.8K hrs min. Telcordia SR-332 (Bellcore) ; 427.3K hrs min. MIL-HDBK-217F (25)
DIMENSION
148*40*32mm (L*W*H)
PACKING
0.21Kg; 40pcs/9.4Kg/1.02CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature. 2. Please refer to "DRIVING METHODS OF LED MODULE". 3. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 4. Tolerance : includes set up tolerance, line regulation and load regulation. 5. De-rating may be needed under low input voltages. Please refer to "STATIC CHARACTERISTIC" sections for details. 6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time. 7. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch
without permanently connected to the mains. 9. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 70 or less.
10. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com 11. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft). 12. For any application note and IP water proof function installation caution, please refer our user manual before using.
https://www.meanwell.com/Upload/PDF/LED_EN.pdf
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:LPF-16-SPEC 2024-10-16
16W Constant Voltage + Constant Current LED Driver
BLOCK DIAGRAM
LPF-16 series
fosc : 100KHz
EMI FILTER
I/P
&
RECTIFIERS
PFC CIRCUIT
POWER
RECTIFIERS
+V
SWITCHING
& FILTER
-V
O.L.P.
O.L.P.
PWM & PFC CONTROL
DETECTION CIRCUIT
O.V.P.
DRIVING METHODS OF LED MODULE
This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs.
100
Vo(%)
50 (min.)
(A) Constant
Voltage area
(B) Constant Current area
(C) Hiccup Protection
50
100
Io(%)
Typical output current normalized by rated current (%)
In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL.
File Name:LPF-16-SPEC 2024-10-16
16W Constant Voltage + Constant Current LED Driver
OUTPUT LOAD vs TEMPERATURE
LPF-16 series
LOAD (%)
THD LOAD (%)
100 80 60 40 20
-35 -30
-15
0
15
30
50
60
AMBIENT TEMPERATURE,Ta ()
70 (HORIZONTAL)
LOAD (%)
100 80 60 40 20
-35 -30
-15
0
15
30
50
60
70 (HORIZONTAL)
Tcase ()
STATIC CHARACTERISTIC
100 90 80 70 60 50 40
90 100 125 135 145 155 165 175 180 200 230 305
INPUT VOLTAGE (V) 60Hz De-rating is needed under low input voltage.
PF
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 60 Constant Current Mode
1.02
1
0.98
0.96
0.94 0.92
277V
0.9
230V
0.88
110V
0.86
0.84
0.82
50%
60%
70%
80%
90%
100%
(16W)
LOAD
TOTAL HARMONIC DISTORTION (THD)
48V Model, Tcase at 60
20%
18%
16%
14%
277VAC
12% 10%
230VAC
8%
115VAC
6%
4%
2%
0%
50%
60%
70%
80%
90%
100%
LOAD
EFFICIENCY(%)
EFFICIENCY vs LOAD
LPF-16 series possess superior working efficiency that up to 86% can be reached in field applications. 48V Model, Tcase at 60
100 90 80 70 60 50 40 30 20 10 0
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
277V 230V 110V
LOAD
File Name:LPF-16-SPEC 2024-10-16
16W Constant Voltage + Constant Current LED Driver
LPF-16 series
LIFE TIME
LIFETIME(Kh)
120
100
80
60
40
20
0
20
30
40
50
60
70
Tcase ( )
File Name:LPF-16-SPEC 2024-10-16
16W Constant Voltage + Constant Current LED Driver
LPF-16 series
MECHANICAL SPECIFICATION
CASE NO.: LPF-16A Unit:mm Tolerance:±1
AC/N(Blue) AC/L(Brown)
300±20 SJOW 17AWG×2C & H05RN-F 2×1.0mm2
148 3.5
3.6
3.6
tc
60
3.5
tc : Max. Case Temperature
300±20 SJOW 17AWG×2C & 05RN-F 2×1.0mm2
+V(Red) -V(Black)
3.5 40
13 3.5
32
Recommend Mounting Direction
INSTALLATION MANUAL
Please refer to:http://www.meanwell.com/manual.html
File Name:LPF-16-SPEC 2024-10-16
MEAN WELL Switching Power Supply Manufacturer