Commission the project :: Interact
User Guide for signify models including: Nature Connect Link Switch Interact, Connect Link Switch Interact, Link Switch Interact, Switch Interact, Interact
Ladattavat materiaalit Signifyn NatureConnectille | Signify
File Info : application/pdf, 23 Pages, 5.49MB
DocumentDocumentCommissioning guide NatureConnect link & Interact June, 2024 1 NatureConnect_Commissioning guide_June 2024 Introduction The NatureConnect system is based on biophilic design principles, which uses elements of nature and natural analogues in indoor spaces to make people feel happy and healthy. Unlike traditional lighting which focuses on visual benefits, NatureConnect additionally brings the biological and emotional benefits of lighting. It reconnects us with the constant cycles and variations of nature for comfortable, engaging and attractive indoor environments. NatureConnect luminaires NatureConnect link is the gateway that creates the NatureConnect light experience. It is programmed with 5 lighting scenes plus OFF status. NatureConnect link Control System (eg Interact) Day Rhythm Tunable White DALI DT8 DIA Energize Relax Present All luminaires connected to the same NatureConnect link will behave in the same way. OFF Off Day Rhythm low The best NatureConnect experience is achieved combining NatureConnect link with presence sensors and user interfaces. NatureConnect switch Wireless, battery free Scene and Off buttons with icons and text for ease of use Interact switch with NatureConnect icons (910505103545) High quality engraving for long durability Presence sensors helps to reduce the power consumption. They can be programmed in a way that when no occupancy is detected, inside the room, they send the signal to the NatureConnect link, to activate "Day Rhythm low" scene or to turn off the luminaires. When presence is detected it goes automatically to "Day rhythm". 2 NatureConnect_Commissioning guide_June 2024 Commissioning You will need a device that supports Interact commissioning app. (e.g. smartphone or a tablet) with Bluetooth technology. For more info check: https://sme.interact-lighting.com/web/help/prf-pra/2.3/install/commissioning.html 1 Test the connection with the luminaires by pressing the service button Service Color transition = Service 1 Press the "service" button to start the test 2 Check luminaires 2 Time configuration - two methods 3 Press the "service" button to finish the test 1 Connect (temporarily) to a wired network that has access to internet/NTP 2 Manually set the time with Windows configuration app NTP LED LED on time acquired from NTP server Connection to network www.signify.com/natureconnect Time is already configured from ! production date 23W48. Please check on the box label. Once the time is set, NatureConnect !! link will keep the time without a perma- nent internet connection. 3 NatureConnect_Commissioning guide_June 2024 Commissioning with interact PRF as Lighting Control System 1 Download the interact office app and create an account 2 Create and structure a new project Create a project Fill in the fields and open the new project just created. 4 NatureConnect_Commissioning guide_June 2024 Create a Light Network 1 2 5 NatureConnect_Commissioning guide_June 2024 Add a group 6 NatureConnect_Commissioning guide_June 2024 3 Reboot NatureConnect link before proceeding with commissioning ! Only needed if production date is before 23W48 Unplug the connector, wait 10 seconds and reconnect. 24V 0.875A ! Wait for the device to start, before proceeding with the next steps. This will take minimum 5 minutes. 4 Find and assign one or more NatureConnect link that belong to the same group. Stand close (2 m ca.) to the SNS210 connected to the NatureConnect link. (Bluetooth must be active on your device.) Tab Light: click on Assign lights It will be found as e.g.: Philips luminaire - **** or NatureConnect link - ****. 1 *2 * * This number is different for each installation 1 Click the left icon to identify the discovered NatureConnect lin and to blink the connected luminaire(s). 2 Click the add button for each NatureConnect link you would like to add to the same group. 7 NatureConnect_Commissioning guide_June 2024 5 Configure the system with motion sensors Tab Controls * Follow below steps: 1 Set CCT to 2700 K Press "enter" or "OK" 2Set Background to 100% Press "enter" or "OK" 3 Set Task to 100 % Press "enter" or "OK" 4 Set Vacant to 0 % Press "enter" or "OK" 5Set Hold time to 10 min Press "enter" or "OK" 6Set Prolong time to 0 min Press "enter" or "OK" * If color temperature slider is missing, follow the procedure indicated in the paragraph B in the Problem Solving chapter. 8 NatureConnect_Commissioning guide_June 2024 Optional: how to add battery power motion sensor 9 NatureConnect_Commissioning guide_June 2024 6 Configure the system without motion sensors * Follow below steps: 1 Set CCT to 2700 K Press "enter" or "OK" 2Set Task level to 100% Press "enter" or "OK" *If color temperature slider is missing, follow the procedure indicated in the paragraph B in the Problem Solving chapter. ! If you are not using any user interface, skip to step 9. 10 NatureConnect_Commissioning guide_June 2024 7 Add one or more user interfaces Day Rhythm Off When more than one ! switch is used, all switches will behave in the same way. Tab Controls: click on Switches Click Show switch in the group Select 4 button switch Identify the switch following the instructions Switch 1 11 NatureConnect_Commissioning guide_June 2024 Test if the switch is added by clicking ON/OFF button Day Rhythm Off Lights turned off? If yes In case luminires in the group do not turn off, follow below steps Retry will restart the add switch flow from the beginning. If the same error occurs again, ! follow the procedure indicated in the paragraph A in the Problem Solving chapter. 12 NatureConnect_Commissioning guide_June 2024 8 Configure the four button switch Configure the TOP LEFT button as the ENERGIZE scene 1 2 3 * WARNING! If you are missing the tunable white slider go to D section (page 20) in the "Problem solving" chapter, at the end of this document. Follow below steps: 1 Type the name of the scene 2Set brightness to 100% Press "enter" or "OK" 3 Set CCT to 2800 K Press "enter" or "OK" 4 Wait 5 seconds 5 Click on "Create" 5 Configure the BOTTOM LEFT button as the RELAX scene 1 2 3 * Follow below steps: 1 Type the name of the scene 2Set brightness to 100% Press "enter" or "OK" 3 Set CCT to 2900 K Press "enter" or "OK" 4 Wait 5 seconds 5 Click on "Create" 5 * If color temperature slider is missing, follow the procedure indicated in the paragraph B in the Problem Solving chapter. 13 NatureConnect_Commissioning guide_June 2024 9 Deploy settings and unlock the network Deploy Unlock 14 NatureConnect_Commissioning guide_June 2024 Additional scenes (optional) ! NOT REQUIRED if using only the user interface. DAY RHYTHM scene Day Rhythm Follow below steps: PRESENT scene 1 2 3 1 Type the name of the scene 2Set brightness to 100% Press "enter" or "OK" 3 Set CCT to 2700 K Press "enter" or "OK" 1 2 3 4 Wait 5 seconds 5 Click on "Create" Follow below steps: 1 Type the name of the scene 2Set brightness to 100% Press "enter" or "OK" 3 Set CCT to 3000 K Press "enter" or "OK" 4 Wait 5 seconds 5 Click on "Create" 5 5 15 NatureConnect_Commissioning guide_June 2024 DEMO MODE It is possible to program a scene that runs in cycle a faster mode of the dynamic scenes. Suitable for demo purposes controlled through the commissioning app. DEMO DAY RHYTHM scene Day Rhythm Follow below steps: DEMO ENERGIZE scene Follow below steps: 1 1 Type the name of the scene 1 1 Type the name of the scene 2Set brightness to 100% 2 Press "enter" or "OK" 3 3 Set CCT to 4700 K Press "enter" or "OK" 2Set brightness to 100% 2 Press "enter" or "OK" 3 3 Set CCT to 4800 K Press "enter" or "OK" 4 Wait 5 seconds 5 Click on "Create" 4 Wait 5 seconds 5 Click on "Create" 5 5 DEMO RELAX scene Follow below steps: 1 1 Type the name of the scene 2Set brightness to 100% 2 Press "enter" or "OK" 3 3 Set CCT to 4800 K Press "enter" or "OK" 4 Wait 5 seconds 5 Click on "Create" 5 16 NatureConnect_Commissioning guide_June 2024 Problem solving A Cannot add a switch to a group (PRF) If it is impossible to make the luminaires react to the switch remove the switch from the configurator and restart the process from the beginning. Go back to commissioning, step 7. 17 NatureConnect_Commissioning guide_June 2024 B What to do if the color temperature slider is missing Under certain circumstances it is possible for the NatureConnect link to not be detected as a tunable white device. To fix this it is necessary to remove it from the system and add it again. Remove NatureConnect link Reboot NatureConnect link 24V 0.875A 1 Remove power for 10 seconds. 2 Wait 5 minutes until the NC link has fully started be- * fore continuing. 3 Go back to step 4: "Find and assign the NatureCon- nect link connected with a SNS210" * During the NC link boot process, the SNS210 looses power temporarily. If this happens during the commissioning processes, you might have to reset the SNS210. 18 NatureConnect_Commissioning guide_June 2024 C What to do when system responds incorrectly to the inputs from the switch It can happen that the scene is saved incorrectly and that the system does not respond or triggers the wrong light experience when pressing a scene button on the switch. This typically happens when you do not wait for 5 seconds between changing the color temperature and pressing the create button. Change the color temperature of the Energize scene to a wrong value on purpose (eg. 6600K) and save. 1 2 Wait 5 seconds, after setting CCT, before clicking on "Save" 3 Change the color temperature of the Energize scene back to correct value (2800K) and save. Repeat the same steps for Relax scene 19 NatureConnect_Commissioning guide_June 2024 1 2 Wait 5 seconds, after setting CCT, before clicking on "Save" 3 D What to do when color temperature slider is missing during scene creation. When scene creation does not work correctly when adding a switch, please use the regular scene menu to create the scene. Go back to Control panel and then go to Scenes panel. color temperature slider is missing 20 NatureConnect_Commissioning guide_June 2024 Create scenes as described on page 13. After go back to Controls panel. Assign scenes to the buttons of the switch. 21 NatureConnect_Commissioning guide_June 2024 Upper left button for Energize Lower left button for Relax 22 NatureConnect_Commissioning guide_June 2024 © 2024 Signify Holding. All rights reserved. The information provided herein is subject to change, without notice. Signify does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract, unless otherwise agreed by Signify. All trademarks are owned by Signify Holding or their respective owners