Instruction Manual for MOUNTUP models including: MU3003 Single Monitor Desk Mount, MU3003, Single Monitor Desk Mount, Monitor Desk Mount, Desk Mount
MOUNTUP Single Monitor Desk Mount, Tall Monitor Stand for 13-32 Inch Screen, Fully Adjustable Computer Desk Mount, Articulating Monitor Arm, VESA Mount with Clamp/Grommet Mounting Base, up to 17.6lbs : Electronics
INSTALLATION INSTRUCTION Safety Caution Hardware Included Please read this instruction carefully before installation. Clamp Bracket All are included in 01A v2 If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us. WARNING: This product contains small items that could be a choking hazard if swallowed. KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED. 01A x1 a Clip Plate b Knob Bolt c Bracket d Bolt e Washer f Washer Before Starting Assembly When attaching brackets to the flat screen, be careful not to over tighten screws and be sure that screws do not bottom out in the mounting holes. Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage, please contact us. L Plate 01B x1 VESA Plate Round Plate 01C x1 Upper Pole 02A x1 Lower Pole 02B x1 Arm 03 x1 3mm Allen key 5mm Allen key Screw M8*10mm Cable Clip Cable Clip Max: 17.6LBS (8KG) 75x75mm 100x100mm DA-1L If you have any questions, please feel free to contact Customer Service via Amazon before returning. Step 1A Clamp Installation 1A-1 1A-2 1A-3 For 10~51mm thickness desk plate 06 Secure the pipe assembly with the preassembled screw 02A 0.39~2" 10~51mm 05A 02B 02B 05B For 51~80mm thickness desk plate 06 Adjust the Clamp height to fit your desk plate. Secure stand to the desktop by tightening Clamp. 2~3.15" 51~80mm Too Short Too Long Correct Correct Do not tighten the screws excessively or your monitor might be damaged. No! 1 Step 1B Grommet Base Installation 1B-1 1B-2 1B-3 02A a Secure the pole assembly with the preassembled screws 05A 02B 01C 02B b 02B 01C 05A 0.39~1.57" 10~40mm a 0.39~2.36" 10~60mm b 04 x1 05A x1 Philips Screws 05B x1 Philips Screws 06 x2 Safety Screw 07A x2 07B x2 Spacers Monitor Kit M4 x 12mm x4 M-A M4 x 30mm x4 M-B M5 x12mm x1 M-C Step 2 Attach the VESA plates to the monitors (a) For Flat Back L10mm x8 M-D 2 (b) For Recessed / Curved Back M4 x 12mm M-A Assemble the upper pole 0022AA and the lower pole 0022BB together 01B 05A Secure the L plate 0011BB to the lower pole 0022BB with the preassembled screws. 05B Secure the clamp bracket to the L plate with the screws 06 3 Assemble the upper pole 0022AA and the lower pole 0022BB together. Dis-assemble the clamp bracket. the marked parts a and b will be used in next step. Assemble the round Position pole assembly on the desk then plate 0011CC to the secure it by tightening the knob bolt lower pole 02B after making knob bolt b through the with the preassem- Long plate aa , desk hole, and the bottom bled screws. of pipe assembly sequentially. 4 M4 x 30mm M-B M-D Note: use 1 piece or 2 pieces of spacers M-D 5 Step 3 Attach the monitors to the stand Assemble the monitor arm 03 and the pole toghther. Bolt Heads UP! Step 4 Tilting Adjustment -90° +90° 03 07B 03 05B Fasten the bolt with 5mm Allen key 0055BC. 07A Attach the cable clips 0077A and 007BB to the stand. Hang the monitor onto the arm then using the safety screw MM-C-D to secure the monitor. Step 5 Switch screen horizontally and vertically If needed, the monitor can be rotated ±90 degrees for switching screen between horizontally and vertically for turn the monitors directly M-C Manage tools and cables Loosen 360° Rotation This function works better for monitors with the center of gravity. 05B 5mm Allen key Loosen tilting bolts, pull monitor to your desired angle, then fasten tilting bolts with the 5mm Allen key 075CB . 6 7 Set the desired angle of the monitor Note: To ensure stability, the tightness of the rotation axis is preset, so it need take some effort to rotate the VESA Plate. Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn't work out, please do not hesitate to ask for our help via Amazon. 8 Product dimensions This cable clip also can take in the Allen keys Desk Desk 31.7" 806mm 2.95" 75mm 3.94" 100mm 38m1.m5" ±90° 1857m.29m" ±90° 1567.m18m" 2.95" 75mm 3.94" 10 0mm ±90 ±90 0.39~3.15" 10~80mm 9 10 11Adobe PDF library 15.00