Installation Guide for PROSCEND models including: 850G-6PI Industrial 6 Port GbE Managed PoE Switch Industrial 5G Cellular Router, 850G-6PI, Industrial 6 Port GbE Managed PoE Switch Industrial 5G Cellular Router, Switch Industrial 5G Cellular Router, Industrial 5G Cellular Router, 5G Cellular Router, Cellular Router, Router
औद्योगिक 6-पोर्ट GbE प्रबंधित PoE स्विच | औद्योगिक 5जी सेल्युलर राउटर निर्माता | PROSCEND
Industrial 6-Port GbE Managed PoE Switch | Industrial 5G Cellular Router Manufacturer | PROSCEND
産業用 6 ポート GbE マネージド PoE スイッチ | 産業用5Gセルラールーターメーカー | PROSCEND
File Info : application/pdf, 1 Pages, 261.76KB
DocumentDocument850G-6PI Industrial Ethernet Switch Quick Installation Guide Connecting Power Version: 1.00 The 850G-6PI Industrial Ethernet Switch can be powered from three power supplies (input range 48~57 VDC). Two power inputs on the terminal block and one Mini-DIN power inlet are on the top panel of the switch. Insert the positive and negative wires (AWG 12-24) into V+ and V- contacts on the terminal block respectively and use a flat-head screwdriver to push in and open the wire clamp. You can use either "Terminal Block" or "Mini-DIN" for primary power and "Terminal Block" for the secondary power source, to be a Redundant Power Input. Check the polarity while connecting. First Power Supply Second Power Supply WARNING The DC power should be connected to a well-fused power supply. Alarm Relay and Ground The alarm relay output contacts are shown as ALM next to the DC terminal block connector as the figure below. The alarm relay out is "Normal Open", and it will be closed when it is detecting any predefined failure such as power failures. The relay output with current carrying capacity of 1A @ 24 VDC. The switch must be properly grounded for optimum system performance. LED Indicators LED PWR/RPS ALM RJ45 LAN port Link/Act RJ45 LAN port Speed UPLINK PoE Color On: Green Off On: Red Off On: Green Blinking: Green Off On: Green Off On: Green Blinking: Green Off On: Green Off Description PWR/RPS is powered. PWR/RPS is not powered. Alarm for abnormal power status or function. Normal operation or DIP switch OFF. Ethernet LINK UP. Ethernet traffic detected. Ethernet LINK DOWN. Ethernet LINK UP at 1000Mbps. Ethernet LINK DOWN or LINK UP at 10Mbps/100Mbps. LINK UP. Traffic detected. LINK DOWN. PoE PD (Powered Device) connected. PoE PD (Powered Device) disconnected. Speed LED (Green) Link/Act LED (Green) RJ45 Connector Pinouts The pin assignment of RJ45 connector is shown in the following table. Pin Description 1,2 T/Rx+, T/Rx- 3,6 T/Rx+, T/Rx- 4,5 T/Rx+, T/Rx- 7,8 T/Rx+, T/Rx- PoE Pinouts V+ VX X DIN-rail Mounting STEP 1: Use the screws to install the DIN-rail kit to attach at the rear side of the switch. Ground Connector DIP Switch Setting DIP 1 (PWR) 2 (RPS) Function Description ON: Primary power alarm reporting is enabled. OFF: Primary power alarm reporting is disabled. ON: Redundant power alarm reporting is enabled. OFF: Redundant power alarm reporting is disabled. Reset Button Function Reboot Reset to factory default Operation Press the Reset button for 2 seconds and release. Press the Reset button for 10 seconds and release. STEP 2: Hook the unit onto the DIN-rail. STEP 3: Push the bottom of the unit towards the DIN-rail until it locks in place. Web Interface: Connect & Login 1. Factory default IP: 192.0.2.1 2. Login with default account and password Username: root Password: 2wsx#EDC NOTE Please scan below QR Code to download online resources. Download Link: https://www.proscend.com/en/product/850G-6PI.html - 1 - 850G-6PI www.proscend.com
PROSCEND is a leading global provider of mission-critical Internet of Things (IoT) connectivity products, services, and solutions with high levels of reliability and security.PROSCEND is a leading global provider of mission-critical Internet of Things (IoT) connectivity products, services, and solutions with high levels of reliability and security.Industrial 6-Port GbE Managed PoE Switch | Industrial 5G Cellular Router Manufacturer | PROSCEND