Jumpflex PROJAM Hero Series Assembly Manual

Important Warnings

Warning: Read all assembly, installation, care, maintenance, and usage instructions in the manual prior to assembling and using the Jumpflex® product.

These products are for personal use only by one person aged 6 years and older.

These products are for outdoor use only.

Warning: For domestic use only. Adult assembly required.

Risk Warning: The use of this product involves a significant risk of participants suffering personal injury, including the possibility of serious injuries, permanent disability or death. All participants who engage in activities with the product do so at their own risk.

Contents

1. PROJAM™ Parts List - Page 4
2. Setup Options - Page 5
3. High Mount Assembly Instructions - Page 6
4. Low Mount Assembly Instructions - Page 17

PROJAM™ Parts List

Setup Options

High Mount

High mount option, ideal for big jumpers and big air slam dunks! Please follow assembly instructions on page 6.

[Image: Diagram showing the backboard and hoop attached to a trampoline enclosure using the high mount setup.]

Low Mount

Low mount option, compatible with SMARTSHADE™™ sun cover and great for little jumpers. Please follow assembly instructions on page 17.

[Image: Diagram showing the backboard and hoop attached to a trampoline enclosure using the low mount setup.]

High Mount Assembly Instructions

1. Lay the Backboard and Hoop (1) face down.

   [Image: Backboard and hoop lying face down, with two attachment points visible at the top.]

2. Join together 4x Fibreglass Rod Connectors (2) and 4 x Fibreglass Rod Ends (3).

   [Image: Two fibreglass rods being joined together with connectors and ends.]

3. Thread one connected fibreglass rod assembly through the webbing loop on the backboard and into the bottom corner pocket.

   [Image: Close-up of a fibreglass rod being threaded through a loop and into a corner pocket.]

4. Repeat step 03 on the other side.

   [Image: Backboard with two fibreglass rods threaded through loops and into corner pockets.]

5. Insert each end of the fibreglass rods into the High Mount Cross Bracket (4) as shown.

   [Image: Close-up of fibreglass rod ends being inserted into the High Mount Cross Bracket.]

   [Image: Backboard with fibreglass rods connected to the High Mount Cross Bracket.]

6. Thread another fibreglass rod assembly into the High Mount Cross Bracket (4) and insert the other end into the corner pocket.

   [Image: Backboard with one fibreglass rod assembly connected to the High Mount Cross Bracket and extending to a corner pocket.]

7. Repeat step 6 on the other side.

   [Image: Backboard with both fibreglass rod assemblies connected to the High Mount Cross Bracket and extending to corner pockets.]

   ! Pull the corner of the backboard away from the center and pre-bend the fibreglass rod to create enough space to insert the rod into the corner pocket.

8. Select any of the enclosure net poles on your Jumpflex® Hero Series Trampoline where you would like to position the PROJAM™™. Remove the top screw cap on the selected net pole, place the assembled High Mount Cross Bracket (5) over the thread and re-screw the top screw cap in place.

   [Image: Diagram showing how to attach the High Mount Cross Bracket to a trampoline net pole.]

   [Image: Close-up of the bracket being secured to the net pole.]

9. Clip the backboard carabiners through the safety net to secure the bottom corners in place.

   [Image: Backboard carabiners being clipped through the safety net.]

   [Image: Close-up of a carabiner securing the bottom corner of the backboard to the net.]

10. Adjust the hoop straps to ensure the hoop is sitting horizontally.

    [Image: Hand adjusting a hoop strap to make the hoop horizontal.]

11. Use the provided Ball Pump (9) to inflate the Basketball (8).

    [Image: Basketball and ball pump.]

Low Mount Assembly Instructions

1. Lay the Backboard and Hoop (1) face down.

   [Image: Diagram showing the backboard and hoop lying face down.]

2. Join together 4x Fibreglass Rod Connectors (2) and 4 x Fibreglass Rod Ends (3).

   [Image: Two fibreglass rods being joined together with connectors and ends.]

3. Thread one connected fibreglass rod assembly through the webbing loop on the backboard and into the bottom corner pocket.

   [Image: Close-up of a fibreglass rod being threaded through a loop and into a corner pocket.]

4. Repeat step 03 on the other side.

   [Image: Backboard with two fibreglass rods threaded through loops and into corner pockets.]

5. Insert each end of the fibreglass rod assembly into the Low Mount Cross Bracket (5) as shown.

   [Image: Close-up of fibreglass rod ends being inserted into the Low Mount Cross Bracket.]

   [Image: Backboard with fibreglass rods connected to the Low Mount Cross Bracket.]

6. Thread 1x fibreglass rod assembly through 1x Low Mount Pole Strap (7) as shown.

   [Image: Fibreglass rod assembly being threaded through a Low Mount Pole Strap.]

7. Connect together the Fibreglass Rod Connector (2) into 1 x Fibreglass Rod End (3), and thread into the Low Mount Cross Bracket (5). Insert the other end into the corner pocket.

   [Image: Diagram showing the connection of the fibreglass rod assembly to the Low Mount Cross Bracket and corner pocket.]

8. Repeat step 07 on the other side.

   ! Pull the corner of the backboard away from the center and pre-bend the fibreglass rod to create enough space to insert the rod into the corner pocket.

   [Image: Diagram illustrating the process of pulling the backboard corner and pre-bending the rod.]

9. Select any two enclosure net poles on your Jumpflex® Hero Series Trampoline where you would like to position the PROJAM™™. Remove the top screw caps on the selected net poles, place the assembled Low Mount Pole Straps (7) over the thread and re-screw the top screw caps.

   [Image: Diagram showing how to attach the Low Mount Pole Straps to trampoline net poles.]

   [Image: Close-up of the pole straps being secured to the net poles.]

10. From the outside of the net enclosure, attach the hook end of the Low Mount Net Connector (6) through net and around the bottom corner of the fibreglass rod assembly.

    [Image: Hand attaching the Low Mount Net Connector to the net and fibreglass rod assembly.]

11. Strap the webbing length around the enclosure pole and re-attach onto the buckle.

    [Image: Webbing strap being secured around the enclosure pole and attached to the buckle.]

12. Repeat steps 11 and 12 on the other side, tighten each webbing strap so the PROJAM™™ is sitting vertically level.

    [Image: Trampoline with PROJAM™™ attached, showing both sides secured with webbing straps.]

    [Image: Close-up of tightened webbing straps ensuring vertical levelness.]

13. Adjust the hoop straps to ensure the hoop is sitting horizontally.

    [Image: Hand adjusting a hoop strap to make the hoop horizontal.]

14. Use the provided Ball Pump (9) to inflate the Basketball (8).

    [Image: Basketball and ball pump.]

Enjoy!