iDatalink - Home
Installation Guide for myFirstech models including: FTI-CDP1 DSI Automotive, FTI-CDP1, DSI Automotive, Automotive
FTI-CDP1 | MyFirstech Install
File Info : application/pdf, 4 Pages, 363.19KB
DocumentDocumentFTI-CDP1 - Vehicle Coverage and Preparation Notes Make DL-CH8 RAM Model 1500 TIP Start Diesel Year Install 2013-17 Type 1 CAN Lights OBD-II Park / Auto Type B IGN BCM Hood I/O Changes BCM Green White/Blue Firmware: Covered vehicles use BLADE-AL(DL)-CH8, confirm application, flash module, and update the controller firmware before installing. CAN: Type 1 vehicles use CAN connections in harness at OBD-II, the included CAN extension is not required for this install type. Lighting: Type B parking lights use the 10-pin connector, please ensure that the unused 6-pin connector is properly secured for safety. Ignition: Common ignition provisions are listed in the BLADE diagram, ignition is also available at the vehicle BCM (connector C5/E, pink/white, pin #27), FTI-CDP1 - Installation and Configuration Notes A Required CAN connections. B Not required. C Hood pin connection (if required). D Ignition jumper, CNOONCNOENCNTETCOTIPOINNKr.equired. E Ignition connection. IIIIIIIIIIIIIIIIIIIIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII D LAN 2001 O O Z K E R E D st. E IIIIIIIII S ID D KO O rG fo AD E R R E 'T T AN NC CE AND WHO O H W WANNA LEARN TO IIIIIIIII BLADE FEATURE COVERAGE CM7000/7200 Cut loop for A/T CM7X00 CM-900S/900AS CM900AS/900S Jumper IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D O OTHER STUFF GOOD TOO IMMOBILIZER DATA PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM DOOR STATUS RAP SHUTDOWN BRAKE STATUS E-BRAKE STATUS TACH OUTPUT GLOW PLUG STATUS SECURE TAKEOVER PARKING LIGHTS CM -900 FTI-CDP1 - DL-CH8 - Type 1 2013-17 RAM 1500 TIP Start Diesel Diesel WTS BLADE PWR pink Set feature option 4-10-4 pink/black *Not required D B B HOOD green pink C A A OF F 3 4 1 Firstech Techfeedtree 2 OBD-II connector 1 1 16 TIP Start Cylinder ACC RUN S 2 TART *Not required Type B Headlight switch 3 AUTO BCM 4 RAP SHUTDOWN C5 - Ignition 48 39 27 26 25 E 10 1 pink/white C INSTALL AFTERMARKET PART IF REQUIRED LED Programming Error Codes Module LED flashing RED during programming 1x - CAN Error, check CAN wiring and voltages 2x - Key code not learned, confirm unlock sent, check CAN 3x - No immobilizer data, check immo data connection 4x - No IGN, check IGN connection 5x - VIN not found, check CAN connections 6x - No immobilizer data, check immo data connection 7x - Not the same key, use only one key for programming 8x - No immobilizer data, check immo data connection 9x - No immobilizer data 10x - Klon error, redo Klon INSTALL GUIDE Patent No. US 8,856,780 CA 2759622 ALL IN ONE DODGE/RAM COM-BLADE-AL(DL)-CH8-EN Doc. No.: ##65995## 20191004 MODULE PROGRAMMING PROCEDURE - WITH KLON 1 Close driver door. 11 OFF Turn key to OFF position. 2 3 4 5 6 7 8 9 10 Re-open driver door to wake up data bus. Press UNLOCK on OEM remote. If the vehicle is not equipped with an OEM remote, press the module programming button. Wait, LED will flash BLUE once [1x]. Turn key to ON position. ON Wait, LED will turn solid RED. OFF Turn key to OFF position. Remove key. Insert key into ignition. Turn key to ON position. ON Wait, LED will flash BLUE. 12 13 WARNING: Disconnect power last. Disconnect RS from vehicle. Connect RS to computer and proceed with extended programming. 14 WARNING: Do not press RS programming button. Connect power first. Connect RS to vehicle. 15 16 17 Turn key to ON position. ON Wait, LED will turn solid BLUE for 2 seconds. OFF Turn key to OFF position. 18 19 START Turn key to START position. OFF Turn key to OFF position. 20 Module Programming Procedure completed. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020 INSTALL GUIDE Patent No. US 8,856,780 CA 2759622 ALL IN ONE DODGE/RAM COM-BLADE-AL(DL)-CH8-EN Doc. No.: ##65995## 20191004 WARNING: READ BEFORE RNEOMTOICTEE STARTING THE VEHICLE IMPORTANT I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction. TAKE OVER PROCEDURE - TO THE VEHICLE OWNER NOTE 2 I All vehicle doors must be closed and locked prior to remote start sequence. TIME RESTRICTI N COMING UP ! 1 Press UNLOCK on after-market remote. 3 TIME RESTRICTI N Within 45 SECONDSfrom previous step: Open vehicle door. Enter vehicle. Close vehicle door. Insert key into ignition. Turn key to ON position. Press and release BRAKE pedal. Take over procedure completed. ! Failure to follow procedure within time restriction will result in vehicle engine shutdown. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020