User Manual for Lumens models including: MXA310, MXA910, MXA920, MXA310 Table Array Microphone, Table Array Microphone, Array Microphone, Microphone
CamConnect Lite User Manual - English Version: 1.0.3 Table of Contents Chapter 1 System Requirements .......................................................... 2 1.1 Operating System Requirements .................................................... 2 1.2 System Hardware Requirements..................................................... 2 Chapter 2 System Connection and Application................................... 3 2.1 System Connection............................................................................. 3 2.2 Scenario................................................................................................. 3 Chapter 3 Support Devices ................................................................... 4 3.1 Shure ...................................................................................................... 4 3.2 Sennheiser ............................................................................................ 4 3.3 Nureva ................................................................................................... 4 3.4 Yamaha .................................................................................................. 4 Chapter 4 Operation Interface Description .......................................... 5 4.1 Main Screen.......................................................................................... 5 4.2 PTZ Control........................................................................................... 7 Chapter 5 Troubleshooting ................................................................... 8 Copyright Information................................................................................ 9 1 Chapter 1 System Requirements 1.1 Operating System Requirements Windows 10 Windows 11 1.2 System Hardware Requirements Item Requirements CPU CPU: Intel i5 / i7 above Memory Memory: 4GB RAM Free Disk Space 1GB Free Disk Space Ethernet Min Screen Resolution: 1920x1080 2 Chapter 2 System Connection and Application 2.1 System Connection POE + Router Microphone System Network cable Network cable USB cable PC (with CamConnect installed) 2.2 Scenario Camera 3 Chapter 3 Support Devices 3.1 Shure Shure MXA310 Table Array Microphone Shure MXA910 Ceiling Array Microphone Shure MXA920 Ceiling Array Microphone 3.2 Sennheiser Sennheiser TeamConnect Ceiling 2 (TCC2) Ceiling Microphone <Note> When using TCC2 with CamConnect, please set and configure the channels on the Sennheiser Control Cockpit software first. CamConnect is divided into 8 equal parts according to Senheisser's horizontal angle of view. They correspond to CamConnect Array Azimuth 1 to 8. If the forbidden area is enabled on the Sennheiser Control Cockpit software, the corresponding position of CamConnect will also be affected. Example: If the forbidden area is set to 0° to 60°, the audio signal from 0° to 45° of CamConnect Array Azimuth 1 and 45° to 60° of Array Azimuth 2 will be ignored. 3.3 Nureva HDL300 Audio Conferencing System 3.4 Yamaha Yamaha RM-CG Ceiling Array Microphone 4 Chapter 4 Operation Interface Description 4.1 Main Screen 1 5 2 3 4 No Item 1 Microphone Device Function Descriptions 1.1 Support Device: The following brands and models are supported Shure: MXA910_ MXA920_ MXA310 Sennhiser: TCC2 Nureva: HDL300 Yamaha: RM-CG 1.2 Device IP: IP location of the microphone device 1.3 Port: Shure: 2202 Sennheiser: 45 Nureva: 8931 1.4 Connect: On/Off 1.5 Advanced 5 2 Preset setting Audio Trigger Level > dB: Triggered only if audio source exceeds the preset dB <Remark>For Sennhiser/ Nureva microphones only Time To Trigger Preset: Capture sound delay setting. When the second point sound triggers, the call preset will be delayed based on the set second. Back To Home Time: Back To Home Time setting. When there is no audio source input on site, reaching the set second will trigger back to Home. Back To Home Position: Home Position setting After the microphone device is connected, the camera can be controlled to turn to the corresponding position according to the microphone detection position. There will be a green light at the front of the detection position. · Tally Light: Receive microphone signal or not (Green for Receive) · Array No.: For Shure microphones · Azimuth Angle: For Sennheiser/ Nureva/ Yamaha microphones Angle can be adjusted manually; Click [Apply] when completed The connected USB cameras will be displayed 3.1 When disconnected, click [Connect] to connect the camera and perform PTZ control. 3 Searching 3.2 When connected, click [Disconnect] to stop the connection. 4 PTZ Control 5 About Click to enable PTZ control Refer to 4.2 PTZ Control for function description Displaying software version information For technical support, please scan the QRcode on the page for assistance 6 4.2 PTZ Control 8 1 2 3 6 4 5 No Item 1 Preview window 2 L/R Direction 3 Mirror / Flip 4 Pan/Tilt/Home 5 Preset setting 6 AF/MF 7 Zoom 8 Exit 7 Function Descriptions Display the screen currently captured by the camera L/R Direction / Normal Set image mirroring/ flip Adjust the Pan/Tilt position of the camera screen Click [Home] key Click the number keys directly to call the preset · Save preset: Click [Set] first and then a number key · Clear preset: Click first and then a number key Switch to Auto Focus/Manual Focus. Focus can be adjusted in Manual. Zoom In/ Zoom Out ratio Exit the PTZ Control page 7 Chapter 5 Troubleshooting This chapter describes problems you may encounter while using Lumens CamConnect. If you have questions, please refer to related chapters and follow all the suggested solutions. If the problem still occurred, please contact your distributor or the service center. NO Problems Solutions 1. Check the power supply of camera or PoE power supply is stable. 1. Unable to search camera devices 2. Make sure the PC is connected to the camera with the USB cable 3. Replace the cables and make sure they are not faulty No response from the microphone Make sure the microphone device is connected (Link) 2. detection position 1.Make sure the Azimuth Angle settings in the CamConnect When using with a Sennhesier software include that angle position 3. microphone, no response at the 2.Make sure if the angle is set as the forbidden area on Sennhesier specific angle Control Cockpit software. Refer to 3.2 Sennhesier Microphone System for details. 8 Copyright Information Copyrights © Lumens Digital Optics Inc. All rights reserved. Lumens is a trademark that is currently being registered by Lumens Digital Optics Inc. Copying, reproducing or transmitting this file is not allowed if a license is not provided by Lumens Digital Optics Inc. unless copying this file is for the purpose of backup after purchasing this product. In order to keep improving the product, the information in this file is subject to change without prior notice. To fully explain or describe how this product should be used, this manual may refer to names of other products or companies without any intention of infringement. Disclaimer of warranties: Lumens Digital Optics Inc. is neither responsible for any possible technological, editorial errors or omissions, nor responsible for any incidental or related damages arising from providing this file, using, or operating this product. 9Microsoft Word 2016 Microsoft Word 2016