Breezary Ceiling Fan - Online Ceiling Fan Store
User Manual for GARMIN models including: CS500 Geiling Fan with Light, CS500, Geiling Fan with Light, Fan with Light, Light
19 ore fa — After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread ...
1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin.
File Info : application/pdf, 7 Pages, 2.71MB
DocumentDocumentCustomer Service: support@ breezary.com Table of Contents Table of Contents..................................................2 Safety Information.................................................2 Dimension Reference............................................3 Hardware Included................................................3 Fan Parts Included................................................3 Installation Instructions.........................................4 Remote Contorl Instructions ................................6 Troubleshooting Guide ........................................7 Safety Information READ AND SAVE THESE INSTRUCTIONS. 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin. 2. All wiring must be in accordancce with the National Electrical Code "ANSI/NFPA 70" and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs (15.9 kg). Use only UL Listed outlet boxes marked " Acceptable for Fan Support of 35 lbs. (15.9 kg) or less. " 4. Do not place objects in the path of the blades. 5. To clean the fixture,turn off the power, wait for it to cool, and wipe the fixture with a clean, soft cloth. 6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipmentgrounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box. 7. All setscrews must be checked and retightened where necessary before installation. WARNING: To reduce the risk of electrical shock or fire, not use this fan with any solid-state fan speed control device. It will permanently damage the electronic circuitry. WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing the rackets balancing the blades, or cleaning the fan. Do not insert balancing the blades, or cleaning the fan. Do not insert WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked "acceptable for fan support of 35 lbs. (15.9 Kg) or less" and use screws provided with the outlet box. WARNING: To avoid possible electrical shock, turn the electricity off at the main fuse box before wiring. WARNING: To reduce the risk of electrical shock, this must be installed with an isolating wall control / switch. CAUTION: To reduce the risk of personal injury, use only the screws provided with the outlet box. CAUTION: The fan must be mounted with a minimum of 7 ft (2.1 m) clearance from the trailing edge of the blades to the floor. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2 Screw Anchor 4 4 Fix Screw 4 Item Name Installation Plate Motor Assembly Remote Control Emitter cBatteries not included Quantity STEP.1 INSTALLATION WALL STOPPER CautionTurn off all switches and make sure there is no power when installing If it is a cement roof, four holes need to be drilled according to the position of the holes on the installation plate, and then inserted into the wall plug. If it's a wooden roof, it doesn't need to be. STEP.2 INSTALLATION PLATE - Thread the power cord through the holes on the installation plate and lock it at the top with four wooden screws. - Remove two symmetrical screws from the installation plate. 4 STEP.3 INSTALLATION MOTOR ASSEMBLY - Hang the safety rope of the fan onto the hook on the installation plate Hook Safety rope - Connect the green ground wire to the ground wire.Connect the white wire to the zero wire.Connect the black wire to the fire wire. Zero wire Frie wire Black wire White wire Ground wire Green ground wire - Clip the keyhole on the fan connection plate into the two screws on the installation plate.Then tighten the four screws Remote contorl instruction -Please pair the remote with the fan before using it. - Open the battery cover on the hand-held remote and install a battery, pair of AAA emitter (1.5V) that are not included. Indicator Light Fan Speed S Fan Stop S Light On/Off Color Temperature Change Natural Wind All Off Pairing Code Timer 1/2/4 h Remote control pairing code: Turn on the power, and press the pairing code button . within 5 seconds. When you hear a "beep" sound or the light flashes, the code pairing is successful. If you need to match the code again, wait 30 seconds and repeat the above operations 6 work Observe the fan for 24 hours after installation. Most noises associated with a new fan disappear during this time 7