Owner's Manual for Winplus models including: WUI-AICAM3WAY, WUIAICAM3WAY, aicam3way, BT534582 3WAY Dashcam Module, BT534582, 3WAY Dashcam Module, Dashcam Module, Module
Winplus Co., Ltd. AICAM3WAY 3WAY Dashcam Module WUI-AICAM3WAY WUIAICAM3WAY aicam3way
Specification MODULE OF BT534582 BT534582 Specification File status [ ] Draft [ ] Published [ ] Pending File name Product specification Version Editor V1.2 Henry Ho Finished 2025-1-3 date Version V1.2 Editor Henry Ho Participator Valid from 2025-1-3 Remark 1 / 8 0 Amendment Specification 1 General Description AB6062S4FB-44PCL series module is a highly integrated 802.11b/g/n/ax Wireless LAN (WLAN) 20/MHz bandwidth 1T1R device with SDIO interface (SDIO 2.0 compliant) and BLE 5.0, based on AltoBeam's ATBM6062 S4FB Wi-Fi6 chip. 2 Feature 2 / 8 3 Specification 3.1 Wi-Fi RF Performance 3.1.1 Output power Specification 3.1.2 EVM for Max. output power 3 / 8 3.1.3 Center frequency tolerance 3.1.4 Receiver sensitivity Specification 4 Drawing 4.1 Mechanical Specifications 4.1.1 Outline drawing The typical size of module is L12.00*W12.00*H1.90mm (±0.2mm). Note: The thickness of module with shield case is 2.35±0.2mm 4 / 8 4.1.2 Pin definition Specification 5 / 8 Specification 5 Remark 5.1 Storage Temperature and Humidity The calculated shelf life in sealed bag is 12 months if stored between 0°C and 40°C at less than 90% relative humidity (RH). After the bag is opened, devices that are subjected to solder reflow or other high temperature processes must be handled in the following manner: a) Mounted within 168-hours of factory conditions < 30 °C /60%RH b) Storage humidity needs to maintained at <10% RH c) Baking is necessary if customer exposes the component to air over 168 hours, baking condition: 125°C / 8hours 6 / 8 Specification FCC Information This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or change to this equipment. Such modifications or change could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. This module is for internal use only and not sold outside. Antenna Information It is 2.4GHz 3216 chip antenna, model 3216X02. Additional testing, Part 15 Subpart B disclaimer: The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247) list on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed when contains digital circuity. The modular must be installed in the host that assign by Company name: Winplus Co., Ltd. Product/PMN: 3WAY Dashcam Module Model no./HVIN: BT534582 The Class II permissive changes is required for each specific host installation Class ll Permissive Change (C2PC) Test Plan for Host Devices Test plan for Class ll Permisive Changes (C2PC) on FCC ID: WUI-AICAM3WAY 1) Output power. (FCC Part 15.247(b)) 2) Output Power Spectral Density. (FCC Part 15.247(e)) 3) AC Conducted Emission. (FCC Part 15.207) 4) Radiated Emission (FCC Part 15.205/209, FCC Part 15.247(d)) 5) Host cannot change the RF Exposure use conditions. lf use conditions is changed the separate approval shall be required. Note 1. These tests be based on C63.10 and FCC Part 15.247 as guidance, according to the operating frequency High, mid and low channel test. 2. For these tests, all modes (IEEE 802.11b, IEEE 802.11g, IEEE 802.11n HT20, IEEE 802.11n HT40, IEEE 802.11ax-HE20, IEEE 802.11ax-HE40) need to be tested. 7 / 8 Specification IC Information -English: This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions: - This device may not cause interference. - This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. -French: Cet appareil contient un ou des émetteurs/récepteurs exempts de licence conformes aux RSS exempts de licence d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes : - Cet appareil ne doit pas provoquer d'interférences. - Cet appareil doit accepter toutes les interférences, y compris les interférences susceptibles de provoquer un fonctionnement indésirable de l'appareil. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. BT534582 3WAY Dashcam Module Responsible Party: Horizon Brands 2975 Red Hill Ave., Ste. 100, Costa Mesa, CA 92626, U.S.A. Tel: 1.866.294.9244 8 / 8Microsoft Word for Microsoft 365