Shuttle NT10H Series Quick Guide

Product Overview

This section details the various ports and features of the Shuttle NT10H series.

1. USB 3.2 Gen2 Type-A port: Power rating USB 3.2: 0.9A (always on).
2. USB 3.2 Gen2 Type-A ports
3. Headphone / Mic in jack
4. Power button / Power LED
5. Ventilation Hole
6. Kensington® Lock Hole
7. USB 4.0 Type-C Ports: Supports DisplayPort and Power Delivery.
8. Power Jack (DC IN)
9. HDMI 2.0 Ports
10. LAN Ports
11. USB 2.0 Port
12. SD Card Reader

More information on this product can be found at: https://bit.ly/NT10H

Hardware Installation

Follow these steps to install M.2 devices, memory modules, and VESA mounts.

Important Safety Note: For safety reasons, please ensure that the power cord is disconnected before opening the case.

A. M.2 Device and Memory Module Installation

Unscrew the four screws of the back cover and remove it.
Locate the M.2 key slots on the motherboard. Install the M.2 device into the M.2 slot and secure it with the provided screw.
- For M.2 2280 M-key and M.2 2230 E-key installation: When installing both simultaneously, use the "M.2 shared nut" to lock the M.2 2230 E-key card on its socket first, then install the M.2 2280 M-key card using an M2*3 screw.
- For M.2 2230 E-key slot with WiFi card: Connect the two antenna cables to the WiFi card (grey cable to 'Aux' and black cable to 'Main'). Affix them with the provided wifi mylar as shown in the diagrams.
- SSD Heatsink Kit: The kit includes thermal pads (70x20x3mm for single-sided SSDs, 70x20x1.5mm for double-sided SSDs). Paste the thermal pad onto the M.2 SSD to effectively reduce its temperature.
Locate the SO-DIMM slots on the motherboard.
Note: This motherboard supports 1.1V DDR5 SO-DIMM memory modules only.
Align the notch of the memory module with the one of the relevant memory slot.
Gently insert the module into the slot at a 45-degree angle.
Carefully push down the memory module until it snaps into the locking mechanism.
Repeat the above steps to install an additional memory module, if required.
Replace and affix the case cover with the four screws.

Installation of VESA Mount

Follow steps 1-3 to install the VESA mount.

Note: Supports 75x75mm and 100x100mm VESA standard.

Connecting to Power

Follow the steps (a-c) to connect the AC adapter to the power jack (DC-IN).
Press the power button to turn on the system.

Power Button Functions:

To put your NT10H into Sleep mode, press the "Power button" once.
If the NT10H is frozen or slow to respond, press and hold the "Power button" for at least 10 seconds to force a shutdown.

Important Power Warning: Do not use inferior extension cords as this may result in damage to your NT10H. The NT10H comes with its own AC adapter. Do not use a different adapter to power the NT10H and other electrical devices.

Safety Information

Operating Temperature: The unit can be operated at an ambient temperature of a maximum of 40°C (104°F). Do not expose it to temperatures below 0°C (32°F) or above 40°C (104°F).

Battery Warning:

THIS PRODUCT CONTAINS A BUTTON BATTERY.
If swallowed, a lithium button battery can cause severe or fatal injuries within 2 hours.
Keep batteries out of reach of children.
If you think batteries may have been swallowed or placed inside any part of the body, seek immediate medical attention.
The product contains non-replaceable batteries.
Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Dispose of used batteries in accordance with the laws of your country.
Battery Disposal: Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.

Altitude: This device is suitable for use at altitudes up to 2000m.

General Compliance:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device meets the requirements for EU conformity in accordance with the currently valid EU directives.
CAN ICES-003(B) / NMB-003(B).
All bundled parts, power cord included, shall not be used without this product.

	Shuttle NA10H Series Quick Start Guide: Hardware Installation and Setup A concise guide to installing hardware, connecting power, and setting up the Shuttle NA10H series Mini PC, including M.2 SSD, RAM, and VESA mount installation.
	Shuttle M15AL01/M15EL01 Quick Start Guide A concise guide to installing and operating the Shuttle M15AL01 and M15EL01 Panel PCs, covering hardware installation, touch panel usage, and safety information.
	Shuttle All-In-One Panel PC Quick Start Guide - M21AL01, M21EL01, M21WL01 This guide provides essential information for setting up and operating Shuttle All-In-One Panel PCs (Models M21AL01, M21EL01, M21WL01), covering installation, component identification, power-on procedures, touch panel usage, maintenance, and safety precautions.
	Shuttle DH670 Series Quick Guide: Installation and Overview A quick guide to installing and understanding the Shuttle DH670 Series mini-PC, covering hardware installation, component setup, and safety information.
	Shuttle P21WL01 Quick Start Guide A quick start guide for the Shuttle P21WL01 Panel PC, covering package contents, product overview, installation steps, touch panel usage, cleaning, and important operational information.
	Shuttle SPCEL12 Edge PC Product Specifications Detailed specifications for the Shuttle SPCEL12 Edge PC, a fanless industrial PC with robust design, supporting triple displays and optional 4G connectivity. Features Intel Celeron J6412 processor, DDR4 RAM, M.2 SSD support, and multiple I/O ports for professional applications like digital signage and edge computing.
	Shuttle DH410 XPC User Manual and Installation Guide Comprehensive user manual and installation guide for the Shuttle DH410 XPC, covering BIOS setup, driver installation, safety precautions, hardware configuration, and hazardous substance declaration.
	Shuttle XPC nano NE10N Barebone: Kompakte Leistung mit Intel N100 Prozessor Produktspezifikationen für den lüfterlosen Shuttle XPC nano NE10N Barebone Mini-PC. Entdecken Sie die Leistung des Intel N100 Prozessors, Dual 4K Display-Unterstützung, umfangreiche Anschlussmöglichkeiten und das kompakte Design für Digital Signage, Kassensysteme und Büroanwendungen.