Imaging.com is for sale | brandforce.com
MBJ - LED Beleuchtungen für industrielle Bildverarbeitung
Instruction Manual for MBJ models including: HDF-05, HDF-07, HDF-10, HDF Series Horizontal Ringlights, HDF Series, HDF Series Ringlights, Horizontal Ringlights, Ringlights
Horizontale Ringlichter - MBJ Imaging
Horizontal Ringlights Operating Manual Technical Data Model Sizes in Series The lightis available in the following sizes 1) HDF-05 HDF-07 HDF-10 1) Size definition: HDF-10 refers to an inner light diameter of 100 mm.
File Info : application/pdf, 2 Pages, 435.97KB
DocumentDocumentMechanical Integration The lights are equipped with 4 combined mounting positions of threaded or through holes. It can be used to fix the lighting to the specified position. To secure a long lifetime additional heat transfer measurements at the holding positions is highly recommended. Example: Model HDF-07 More 2D and 3D drawings can be found online: www.mbj-imaging.com Safety Notes Before working with this unit, read the warning and application instructions carefully and completely before operating the device. Operating Manual Technical Data Horizontal Ringlights Specification Operating temperature Certifications Degree of protection Humidity Horizontal Ringlight Series 10°C to 30°C CE, RoHS IP54 30 % to 70 % 1. The device is designed for indoor use only. 2. Light Due to the risk of flash burn of the eyes it is not recommended to look directly into the light source. The lighting must be switched off before installation and/or maintenance. The device must not be used when a failure may cause a personal injury. 3. Heat - In case of insufficient heat dissipation or when running the light in flash mode with a too high duty cycle, the surface temperature may exceed 60 °C. Keep off flammable materials at any time. 4. Electricity - The housing is electrically isolated from the ground of the power supply. Exceeding the permissible input voltage Uin or ULED(+) can lead to the destruction of the device or to a significant shortening of the lifetime of the LEDs in the device. 5. Usage Please prevent mechanical stress to the light surface during operation. This will lead to a inhomogenious light emission. 6. Cleaning - The light emission surface has to be cleaned with a standard glass cleaner and a soft cleaning cloth. Do not use other material for cleaning as it will damage the device. 03203.04 Manual MBJ Horizontal Ringlight HDF-Series, August 2023 MBJ Imaging GmbH Jochim-Klindt-Straße 7 +49 4102 778 90 31 22926 Ahrensburg, Germany sales@mbj-imaging.com www.mbj-imaging.com Model Sizes in Series The lightis available in the following sizes 1) HDF-05 HDF-07 HDF-10 1) Size definition: HDF-10 refers to an inner light diameter of 100 mm. Possible LED Colors LED Abbr.1) Peak Wavelength2) White -WT 5000 K, CRI80 Red -RD near 625 nm Infrared -IR near 850 nm Green -GN near 525 nm Blue -BE near 465 nm Yellow -YE near 580 nm 1) Color option will be added to the model name after the size information. HDF-07-RD refers to a horizontal ringlight with 625 nm red light. 2) This is an approximated value. The exact value also depends on LED temperature and LED current. Electrical Connection The lighting is equipped with an 4 pin M8x1 connector. Pin Color 1) Standard (-s) Direct (-x) 2) 1 brown 24 VDC LED (+) 2 white Dim LED (+) 3 blue Trigger LED (-) 4 black Ground LED (-) 1) wire color of MBJ lighting cable 2) connection to 24VDC without external LED controller may destroy the unit Additional Information: Pin3 (Trigger) is an `active high' input signal with 5...24 V=ON and 0...1 V=OFF, it is a high resistance current sink with 0.2 mA for 5 V and 5 mA for 24 V Pin2 (DIM) is used as brightness control and operation mode switch, it is a high resistance current sink with 0.2 mA for 5 V and 1 mA for 24 V. For the connection it is recommended to use the MBJ lighting cable with a maximum length of 10 m. Integrated Controller (-s) Supported operation modes with the integrated LED controller Pin 2 (Dim) Operation mode 24 V steady light 1) 1...10 V steady light with brightness control 2) 24 V triggered light GND triggered flash light with max. 20 ms and up-to 100 % more light intensity 3) 1) Pin 3 (Trigger) needs permanent 24 V to activate steady light mode 2) PWM with 3.8kHz clock is used, recommended minimal camera exposure is 5ms 3) Latency between trigger and LED light ON is about max. 30µs, the maximum recom- mended clock speed is 1 kHz, the maximum recommended duty cycle is 25 % and the minimum recommended flash time is 100 µs Application Samples for (-s) controller Steady light 24 VDC 1 Power 2 Dim MBJ LED light 3 Trigger 4 GND Steady light with brightness control 24 VDC 24 VDC 3k9 1 Power 2 Dim MBJ 10k LED light 3 Trigger 4 GND Specification HDF-05 HDF-07 HDF-10 Optical parameter Luminous area (ID) Light emission 50 mm 75 mm Horizontal, side fired ringlight with slightly diffuse light emission 100 mm Recommended use used mainly for darkfield applications Recommended light working distance 1 mm - 30 mm Electrical parameter Available interfaces -s with integrated LED Controller and 4 operation modes; -x with direct LED access (external LED control is required) Uin for -s Version 24 VDC +/- 5 % ULed(+) range for -x version2) Typical Power (-s version) WT / BE / YE: 17 ... 20 VDC; GN: 20 ... 23 VDC; RD: 12 ... 15 VDC; IR: 9 ... 12 VDC Steady light operation 6 W / 3 W / 2 W During ON time at flashed light operation 16 W Recommended LED current (-x version) Steady light (100 % duty cycle) 300 mA (450 mA for IR) Flash light (50 % duty cycle, < 500 ms pulse) 600 mA (450 mA for IR) Flash light (25 % duty cycle, < 50 ms pulse) 900 mA (450 mA for IR) Flash light (10 % duty cycle, < 5 ms pulse) 1200 mA (900 mA for IR) General parameter Dimension (H x W x D) 130 mm x 141 mm x 12 mm 130 mm x 141 mm x 12 mm 130 mm x 141 mm x 12 mm Weight 360 g 330 g 300 g Material Black anodized aluminum housing with PMMA light guide Connector M8x1 socket, 4 pin, male (for pinning details refer to chart "Electrical Connection") Accessories For cable and external LED controller: please check www.mbj-imaging.com 1) Values are approximate with +/- 7 % tolerance 2) Lower voltage value refers to steady light, higher voltage value refers to flash light, please see max. allowed current in the rows below. 3) Power for Blue / Yellow is comparable to White, Power for Green is approx. 1,2 times higher. 4) Triggered flash light with max. 20 ms and up to 100 % more light intensity, calculated for White. Triggered light with NPN sinking output (inverted strobe signal, open collector) 24 VDC 2k2 from Camera/ PLC etc 11 mA 1 Power 2 Dim MBJ LED light 3 Trigger 4 GND Flashed light with PNP sourcing 24 VDC from Camera/ PLC etc 24 VDC 15 mA 2k2 1 Power 2 Dim MBJ LED light 3 Trigger 4 GND